Federal Signal Corporation FireRay Scene Light User manual

25500386
A1 0320
Printed in U.S.A
© Copyright 2016-2020 Federal Signal Corporation
Installation and Maintenance Instructions
FireRay®Scene Light

Limited Warranty
This product is subject to and covered by a limited warranty,
a copy of which can be found at www.fedsig.com/SSG-Warranty.
A copy of this limited warranty can also be obtained by written
request to Federal Signal Corporation, 2645 Federal Signal Drive,
University Park, IL 60484, email to [email protected] or
call [phone].
This limited warranty is in lieu of all other warranties, express or
implied, contractual or statutory, including, but not limited to the
warranty of merchantability, warranty of tness for a particular
purpose and any warranty against failure of its essential purpose.
2645 Federal Signal Drive
University Park, Illinois 60484
www.fedsig.com
Customer Support
Police/Fire-EMS: 800-264-3578 • [phone]
Work Truck: 800-824-0254 • [phone]
Technical Support 800-433-9132 • [phone]
All trademarks are property of their respective owners.

3
Installallation and Maintenance Instructions
Federal Signal www.fedsig.com
Contents
Safety Message to Installers and Service Personnel.....................4
Safety Message to Operators...........................................................5
Overview of the FireRay Scene Light ..............................................6
Unpacking the Product .....................................................................6
Installing the FireRay ........................................................................6
Making Electrical Connections ......................................................13
Getting Technical Support.............................................................. 14
Getting Repair Service....................................................................15
Figures
Figure 1 Mounting Holes (Not to scale).......................................... 7
Figure 2 Exploded View - No Bezel................................................9
Figure 3 Exploded View - With Bezel............................................10
Figure 4 FR6 Base .......................................................................... 11
Figure 5 FR7 and FR9 Base...........................................................12
Figure 6 Light Orientation..............................................................13
Tables
Table 1 Kit Contents ......................................................................... 6

4FireRay®Scene Light
Federal Signal www.fedsig.com
Safety Message to Installers and Service Personnel
Safety Message to Installers and Service Personnel
People’s lives depend on your proper installation of our
products. It is important to read, understand, and follow all
instructions shipped with the products. Listed below are some
other important safety instructions and precautions you should
follow:
• To properly install this light, you must have a good
understanding of automotive electrical procedures and
safety warning equipment.
• DO NOT install equipment or route wiring or cord in the
deployment path of an airbag.
• If a vehicle seat is temporarily removed, verify with the
vehicle manufacturer if the seat needs to be recalibrated for
proper airbag deployment.
• When drilling into a vehicle structure, ensure that both sides
of the surface are clear of anything that could be damaged.
• Locate the light control so the VEHICLE and CONTROL can
be operated safely under all driving conditions.
• Do not attempt to activate or deactivate light control while
driving in a hazardous situation.
• This product contains high intensity LED devices. To prevent
eye damage, DO NOT stare into the light beam at close
range.
• Frequently inspect the light to ensure that it is operating
properly and that it is securely attached to the vehicle.
• File these instructions in a safe place and refer to them when
maintaining and/or reinstalling the product.
Failure to follow all safety precautions and instructions may
result in property damage, serious injury, or death to you or
others.

5
Installallation and Maintenance Instructions
Federal Signal www.fedsig.com
Safety Message to Operators
Safety Message to Operators
Peoples’ lives depend on your safe use of our products. Listed
below are some important safety instructions and precautions
you should follow:
• Although your warning system is operating properly, it
may not be completely eective. People may not see or
heed your warning signal. You must recognize this fact and
continue to drive cautiously.
• Situations may occur which obstruct your warning signal
when natural or man-made objects are between your vehicle
and others, such as: raising your hood or trunk lid. If these
situations occur, be especially careful.
• This product contains high intensity LED devices. To prevent
eye damage, DO NOT stare into the light beam at close
range.
• At the start of your shift, you should ensure that the light is
securely attached and operating properly.
Failure to follow these safety precautions may result in property
damage, serious injury, or death to you, to passengers, or to
others.

6FireRay®Scene Light
Federal Signal www.fedsig.com
Installing the FireRay
Overview of the FireRay Scene Light
The FireRay Scene light is a self-contained, high intensity, LED
light designed for mounting to the exterior of a vehicle. FireRay
Scene Lights are designed for operation on 12 Vdc.
Unpacking the Product
After unpacking the light, inspect it for damage that may
have occurred in transit. If it has been damaged, file a claim
immediately with the carrier, stating the extent of damage.
Carefully check all envelopes, shipping labels, and tags before
removing or destroying them. If installing a permanent mounted
beacon, ensure that the parts listed in Table 2 are included in
the package.
Table 1 Kit Contents
Qty Description Part No.
2 #8 x 1-inch Stainless Steel Screw 7011242-16
2 Plastic Screw Grommet 7065073
Installing the FireRay
AIRBAG DEPLOYMENT: Do not install equipment or route wiring
in the deployment path of an airbag. Failure to observe this
warning will reduce the eectiveness of the airbag or potentially
dislodge the equipment, causing serious injury or death.
NOTE: For maximum coverage and eectiveness, mount the
light assembly in a horizontal orientation. See Figure 1.
Before proceeding with installation, determine the approximate
location of the light assembly and plan all cable/wire routing.
To install the FireRay:
1. Position the Scene light assembly on the desired mounting
surface. Ensure that the unit is level side to side. See
Figure1.

7
Installallation and Maintenance Instructions
Federal Signal www.fedsig.com
Installing the FireRay
Figure 1 Mounting Holes (Not to scale)
2. Using the dimensions provided in Figure 2, scribe the two
mounting hole locations and a wiring routing hole location
on the mounting surface.

8FireRay®Scene Light
Federal Signal www.fedsig.com
Installing the FireRay
DAMAGE TO LIGHT: When installing the FireRay scene light on
a vehicle, you MUST use the manufacturer’s supplied mounting
gasket, screws, and screw grommets. Do not use an impact
drill or an electric screw gun when installing the light. Torque
the mounting screws to the manufacturer’s recommended
specication of 7.8-11.3 in-lb. Failure to observe these
precautions damages the scene light and void any warranty
claims for the light.
DRILLING PRECAUTIONS: When drilling holes, check the area
you are drilling into to ensure that you do not damage vehicle
components while drilling. All drilled holes should be de-burred,
and all sharp edges should be smoothed. All wire routings going
through drilled holes should be protected by a grommet or
convolute/split loom tubing.
3. Drill two 1/4-inch mounting holes and a 1-inch wire routing
hole at the previously scribed locations.
4. Install the two supplied plastic screw grommets into the two
1/4-inch mounting holes.
NOTE: When removing the FireRay Scene light, inspect the
mounting grommets for wear and replace them as needed.
5. Complete the electrical connections as described in the
Making Electrical Connections section. The FireRay warning
light assembly has five 8.7-inch long lead wires, which exit
out the back of the unit, for making electrical connections.
6. Align the Scene light assembly with the previously inserted
plastic screw grommets and secure with the provided #8 by
1-inch stainless steel screws for FR6 and FR7 models. For
the FR9 model, use #8 by 2-inch stainless steel screws. See
Figures 2 and 3.

9
Installallation and Maintenance Instructions
Federal Signal www.fedsig.com
Installing the FireRay
Figure 2 Exploded View - No Bezel

10 FireRay®Scene Light
Federal Signal www.fedsig.com
Installing the FireRay
Figure 3 Exploded View - With Bezel