Federal Signal Corporation MB-IDENT03 Manual

Safety Message to Installers of Warning Light Equipment
People’s lives depend on your proper installation and servicing of Federal Signal products. It is important
to read and follow all instructions shipped with this product and the original product. Listed below are
some other important safety instructions and precautions you should follow.
Before Installation or Service
Qualifications
• To properly install or service this equipment, you must have a good understanding of automotive
mechanical and electrical procedures and systems, along with proficiency in the installation and
service of safety warning equipment. Always refer to the vehicle’s service manuals when performing
equipment installations on a vehicle.
Light Hazards
• To be an eective warning device, this product produces bright light that can be hazardous to your
eyesight when viewed at a close range. Do not stare directly into this lighting product at a close
range, or permanent damage to your eyesight may occur.
• Do not install the light system in an area that would block, impair, or blind the driver’s vision. Ensure
that the light system is mounted in a position that is outside the driver’s field of vision, so the driver
can safely operate the vehicle.
• Federal Signal power supplies and light heads are designed to work together as a system. Combining
light heads and a power supply from dierent manufacturers may reduce the warning eectiveness of
the lighting system and may damage the components. You should verify or test your combination to
ensure that the system works together and meets federal, state, and local standards or guidelines.
Electrical Hazards
• A light system is a high current system. In order for the system to function properly, a separate
negative (-) connection and positive ( +) connection must be made. All negative connections should
be connected to the negative battery terminal, and a suitable fuse should be installed on the positive
battery terminal connection as close to the battery as possible. Ensure that all wires and fuses are
rated correctly to handle the device and system amperage requirements.
• Never attempt to install aftermarket equipment that connects to the vehicle wiring without reviewing
a vehicle wiring diagram available from the vehicle manufacturer. Ensure that your installation will not
aect vehicle operation or mandated safety functions or circuits. Always check the vehicle for proper
operation after installation.
• The lighting system components, especially light bulbs, strobe tubes, LEDs, and the outer housing,
get hot during operation. Disconnect power to the system and allow the system to cool down before
handling any components of the system.
• Do not mount a radio antenna within 18 inches (45.7 cm) of the lighting system. Placing the antenna
too close to the lighting system could cause the lighting system to malfunction or be damaged by
strong radio fields. Mounting the antenna too close to the lighting system may also cause the radio
noise emitted from the lighting system to interfere with the reception of the radio transmitter and
reduce radio reception.
MB-IDENT03 Identier Board Installation,
Maintenance, and Service Manual
25500768 Rev. A0 0222

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
2MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
• Do not attempt to wash any unsealed electrical device while it is connected to its power source.
During Installation and Service
• DO NOT get metal shavings inside the product. Metal shavings in the product can cause the system
to fail. If drilling must be done near the unit, place an ESD-approved cover over the unit. Inspect the
unit after mounting to verify that there are no shavings present in or near the unit.
• DO NOT connect this system to the vehicle battery until ALL other electrical connections are made,
mounting of all components is complete, and you have verified that no shorts exist. If the wiring is
shorted to the vehicle body or frame, high current conductors can cause hazardous sparks, resulting
in electrical fires or flying molten metal.
• DO NOT install equipment or route wiring (or the plug-in cord) in the deployment path of an airbag.
• Before mounting any components, check the manual to ensure that the component you are installing
is suitable for use in that area of the vehicle. Many components are not suitable for use in the engine
compartment or other extreme environmental exposure areas.
• When drilling into a vehicle structure, ensure that both sides of the surface are clear of anything that
could be damaged. Remove all burrs from drilled holes. To prevent electrical shorts, grommet all
drilled holes through which wiring passes. Ensure that the mounting screws do not cause electrical or
mechanical damage to the vehicle.
• Refer to the manual packed with the lighting system for proper electrical connections, additional
precautions, and information.
After Installation or Service
• After installation, test the light system to ensure that it is operating properly.
• Test all vehicle functions, including horn operation, vehicle safety functions, and vehicle light systems,
to ensure proper operation. Ensure that the installation has not aected the vehicle operation or
changed any vehicle safety function or circuit.
• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat needs to be
recalibrated for proper airbag deployment.
• Scratched or dull reflectors, mirrors, or lenses will reduce the eectiveness of the lighting system.
Avoid heavy pressure and the use of caustic or petroleum-based products when cleaning the lighting
system. Replace any optical components that may have been scratched or crazed during system
installation.
• Do not attempt to activate or deactivate the light system control while driving in a hazardous situation.
• Frequently inspect the light system to ensure that it is operating properly and is securely attached to
the vehicle.
• After installation and testing are complete, provide a copy of these instructions to instructional sta
and all operating personnel.
• File these instructions in a safe place and refer to them when maintaining and/or reinstalling the
product.
Failure to follow all safety precautions and instructions may result in property damage, serious injury, or
death.

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
3
MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
Introduction
The Federal Signal LED Model MB-IDENT03 Identifier Board is a supplemental identification device.
The fixed “STATE PATROL’’ display is created by blue, high brightness, wide-angle LEDs. It operates at a
nominal input of 13.6 Vdc (11 Vdc minimum).
The Identifier Board lens is thermoformed PETG material, which is a thermoplastic polyester material
comparable to polycarbonate impact resistance properties, with bracketry made from 11-gauge steel. It
has a 15-foot power and ground·wire harness. Mounting hardware is supplied.
The Identifier Board has an operating temperature range of -30°C to +65°C (-22°F to +149°F).
Table 1 Dimensions
Length x Width x Height 24.0 x 1.0 x 4.1 inches (61.0 x 2.6 x 10.4 cm)
Weight 5.6 lb (2.54 kg)
Unpacking the Kit
After unpacking the kit, inspect it for damage that may have occurred in transit. If it has been damaged,
do not attempt to install or operate it. File a claim immediately with the carrier, stating the extent of
damage. Carefully check all envelopes, shipping labels, and tags before removing or destroying them.
Ensure that the parts listed in Table 2 are included in the package. If you are missing any parts, contact
Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through Friday (CT).
Table 2 Kit contents
Qty. Description Part Number
1 Window Guard (With/C-Wires) / Lens (Potted) Message Board PCBA 20000546/865203582
10 5/8-inch Black Ox. Stainless Steel FLat Head Hex Dr. Screw 70001429A-10
1 Window Guard Message Board Mounting Plate 865203902A
2 Message Board Front Fastener Strip 865203903A
2 Message Board Rear Fastener Strip Assembly 865203905A
Installing the MB-IDENT03 Message Board
To mount the MB-IDENT03 Message Board onto the Rear Window Guards:
1. For installation purposes, determine the proper location on the Rear Window Guard by placing the
already assembled model on the Rear Window Guard grille surface to make sure the exit wires on
the model are not pinched or covered by any of the metal webbing on the window guard.
2. Once the proper light position is located on the window guard, mark all four corner edges of the light
assembly with a pencil.
3. Set the light assembly on a clean, flat surface and carefully remove all ten of the mounting screws
and set the screws aside.
4. For the next two steps, have another person help to hold and align the assembly during the
placement of the light assembly and the re-fastening of the screws to mount the light assembly to the
window guard. The light assemblies will be on the outside surface of the window guards.
If window guard is already installed on the vehicle, make sure window is rolled down and both sides
of the window guard are easily accessible.

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
4MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
5. Carefully lift the upper Front Fastener Strip, lens/PC board assembly, and large mounting plate all
together. While keeping these parts together, place the light within the marked locations on the
outside surface of the window guard. Keep the wires away from any edges to avoid the chang of
wires after installation. See Figure 1.
Figure 1 Exploded Assembly View
1
2
3
4
6
5
Window guard not included
in MB-IDENT03 Message
Board Kit
6. Once the light assembly is in position, insert one flat head machine screw through the top left hole
front fastener strip and through the assembly while the Rear Fastener Strip is being held on the
opposite side of the window guard. See Figure 2.
Figure 2 Side View of Message Board Mounted on Window Guard

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
5
MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
7. Loosely tighten that first inserted screw. Insert a second flat head machine screw into the top right
hole of the Front Fastener Strip and through the assembly into the Rear Fastener Strip and loosely
tighten the screw while the upper Rear Fastener Strip is being held in place on the opposite side of
the window guard.
8. Being careful not to scratch the lens, add and align the lower Front Fastener Strip to the bottom front
assembly, and insert a flat-head machine screw into the left corner hole of the Front Fastener Strip
and loosely tighten the screw. See Figure 1.
9. Insert another flat head machine screw to the right corner hole of the lower Front Fastener Strip and
through the assembly while the lower Rear Fastener Strip is being held in place on the opposite side
of the window guard. Fasten the screw into the Rear Fastener Strip and loosely tighten the screw.
See Figure 3.
Figure 3 Rear View of Message Board Mounted on Window Guard
10. Add the remaining six flat head machine screws to the assembly and make any final alignment
position adjustments to the light before securing all ten screws. Do not use impact tools while
securing the screws to the assembly, as they may crack the lens/PC board assembly.
LIGHT HAZARD: To be an eective warning device, an emergency warning system produces
bright light that can be hazardous to your eyesight when viewed at a close range. Do not stare
directly into this lighting product at a close range, or permanent damage to your eyesight may
occur.

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
6MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
11. After the light assembly has been secured, make the necessary wire connections to the red (+12 Vdc
battery) and black (-) wires, and then check for proper light operation. See Figure 4.
Figure 4 Front ISO Assembled View Mounted on Rear Window Guard
12. Secure and conceal the wires.
13. Installation steps for driver and passenger side Message Board assemblies are the same.

MB-IDENT03 Identier Board Installation, Maintenance, and Service Manual
7
MB-IDENT03 Identier Board
Federal Signal www.fedsig.com
Getting Technical Support and Service
For technical support and service, please contact:
Service Department
Federal Signal Corporation
Phone: [phone]
Email: [email protected]
Getting Repair Service
The Federal Signal factory provides technical assistance with any problems that cannot be handled
locally.
Any units returned to Federal Signal for service, inspection, or repair must be accompanied by a Return
Material Authorization (RMA). Obtain an RMA from a local Distributor or Manufacturer’s Representative.
Provide a brief explanation of the service requested or the nature of the malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation
Service Department
2645 Federal Signal Drive
University Park, IL 60484-3167
Ordering Replacement Parts
To order replacement parts, call Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through
Friday (CT), or contact your nearest distributor.
Limited Warranty
This product is subject to and covered by a limited warranty, a copy of which can be found at
www.fedsig.com/SSG-Warranty. A copy of this limited warranty can also be obtained by written
request to Federal Signal Corporation, 2645 Federal Signal Drive, University Park, IL 60484, email to
[email protected] or call [phone].
This limited warranty is in lieu of all other warranties, express or implied, contractual or statutory,
including, but not limited to the warranty of merchantability, warranty of fitness for a particular purpose
and any warranty against failure of its essential purpose.

2645 Federal Signal Drive
University Park, Illinois 60484-3167
www.fedsig.com
Customer Support
Police/Fire-EMS: 800-264-3578 • [phone]
Work Truck: 800-824-0254 • [phone]
Technical Support: 800-433-9132 • [phone]
© Copyright 2022 Federal Signal Corporation
All product names or trademarks are properties of their respective owners.