
All cross-cut shredders require oil for peak
performance. If not oiled, a machine may
experience diminished sheet capacity, intrusive
noise when shredding and could ultimately
stop running. To avoid these problems, we
recommend you oil your shredder each time
you empty your waste bin.
OILING SHREDDER
3
Set to Off (0)
1
3
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects in
material and workmanship and provides service and support for 2 years from the date of purchase by the
original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material
and workmanship for 5 years from the date of purchase by the original consumer. If any part is found to
be defective during the warranty period, your sole and exclusive remedy will be repair or replacement,
at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse,
mishandling, failure to comply with product usage standards, shredder operation using an improper
power supply (other than listed on label), or unauthorized repair. Fellowes reserves the right to charge
the consumers for any additional costs incurred by Fellowes to provide parts or services outside of the
country where the shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING
THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any
consequential or incidental damages attributable to this product. This warranty gives you specific legal rights.
The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations,
restrictions, or conditions may be required by local law. For more details or to obtain service under this
warranty, please contact us or your dealer.
Continuous operation:
4-5 minutes maximum
NOTE: Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
4-5-minutes will trigger
20-minute cool down period.
BASIC SHREDDING
TROUBLESHOOTING
BASIC PRODUCT MAINTENANCE
CARD
Paper jam: Set to Off and empty bin. Replace bin and follow any or all of the below procedures.
LIMITED PRODUCT WARRANTY
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
PAPER
Set to Reverse (R) Set to Off (0) Pull uncut paper
from paper entry
Set to Reverse (R)
Alternate slowly back and forth
Set to Off
*Apply oil across entry Set to Reverse (R)
2-3 seconds
ATTENTION: If the SafeSense®light remains on, you must engage the Override Switch in order to perform steps above. Once the jam is cleared, reset the
SafeSense®feature. (See SafeSense®instructions below.)
SafeSense®paper jam: If the SafeSense®feature activates (SafeSense®light remains on) to cause the user to think
the shredder has jammed when it has not, use the Override Switch to deactivate the SafeSense®feature and clear
the paper. Warning – when switch is in override position, the SafeSense®light will flash and the SafeSense®feature will
NOT function. Once the paper is cleared, reset the SafeSense®feature.
SafeSense®override switch
Active Not active
Sensor light illuminated–paper
jammed
Press Auto-On ( I )
Feed into paper entry
and release
34 45
Set to Off
42
Feed into center of
entry and release
Set to Off
Press Auto-On ( I )
Hold credit card at edge
34 5
Set to Off
2 6
12 3 45 6
2
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Plug in and put disconnect
power switch in ON (I) position
1
Plug in and put disconnect
power switch in ON (I) position
1
Shredder doesn’t start:
Yellow - SafeSense
®
active
Yellow flashing - SafeSense
®
not active
Make sure bin is pushed in
Make sure control switch is in
Auto-On ( I ) position
Wait 20 minutes for red light to
turn off
Make sure Safety lock is in
the unlock position