Ferm AGM1066S User manual

WWW.FERM.COM
EN
DE
NL
FR
ES
PT
IT
SV
FI
NO
DA
HU
CS
SK
PL
LT
LV
RO
RU
EL
AR
TR
Original instructions 05
Übersetzung der Originalbetriebsanleitung 12
Vertaling van de oorspronkelijke gebruiksaanwijzing 20
Traduction de la notice originale 28
Traducción del manual original 36
Tradução do manual original 44
Traduzione delle istruzioni originali 52
Översättning av bruksanvisning i original 60
Alkuperäisten ohjeiden käännös 67
Oversatt fra orginal veiledning 74
Oversættelse af den originale brugsanvisning 81
Eredeti használati utasítás fordítása 88
Překlad püvodního návodu k používání 95
Prevod izvirnih navodil 103
Tłumaczenie instrukcji oryginalnej 110
Originalios instrukcijos vertimas 118
Instrukciju tulkojums no oriģinālvalodas 125
Traducere a instrucţiunilor originale 132
Перевод исходных инструкций 139
Μετάφραση του πρωτοτύπου των οδηγιών χρήσης 148
ترجمة التعليمات الأصلية 157
Orijinal talimatların çevirisi 163
AGM1066S
AGM1066S
AGM1066S

8
EN
Never attempt to remove the cut-off wheel
from the cut while the wheel is in motion
otherwise kickback may occur. Investigate
and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power tool
is restarted in the workpiece.
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides
of the wheel.
f) Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the voltage of the
power supply corresponds to the voltage
on the rating plate label.
Class II machine - Double insulation - You
don’t need any earthed plug.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
2. MACHINE INFORMATION
Intended use
Your angle grinder has been designed for grinding
masonry and steel materials without the use of
water. For cutting, a special protection guard
must be used (not included) Fig. D2.
Technical specifications
Model No AGM1066S
Mains voltage 230-240 V~
Mains frequency 50 Hz
Power input 2000W
Rated speed 8.000 /min
Wheel disc for grinding
Diameter 180 mm
Bore 22.2 mm
Thickness 6 mm
Wheel disc for cutting
Diameter 180 mm
Bore 22.2 mm
Thickness 3 mm
Spindle thread M14
Weight 4.24 kg
Sound pressure (LPA)92.4 + 3 dB(A)
Acoustic power (LWA)103.9 + 3 dB(A)
Vibration “Surface grinding” ah,AG 9.95 + 1.5 m/s2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in
EN 60745; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
• using the tool for different applications, or with
different or poorly maintained accessories,
may significantly increase the exposure level
• the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level
Protect yourself against the effects of vibration by