FILL-RITE FR1118-A10 User manual

FR1118-A10
User’s Manual
WARNING
Read carefully and understand all INSTRUCTIONS before operating.
Failure to follow the safety rules and other basic safety precautions may result
in serious personal injury. Save these instructions in a safe place and on hand
so that they can be read when required.
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]

Fig. 1
1. INTRODUCTION
1.1 Technical Data
1.1.1 The turbine digital meter is designed for use with the following low viscosity fluids:
-diesel fuel
-kerosene
1.1.2 Flow Rate: 3-26GPM, flow rates outside of this range may have reduced accuracy.
1.1.3 Operating pressure: 10BAR / 145PSI
1.1.4 Inlet/Outlet: 1”
1.2 LCD DISPLAY
The meter display features two numerical registers and several function or status indicators.
# Description
1 Resettable Register (5 digit, from 0.1-99999).
2 Battery condition.
3 “Calibration” mode.
4 Resetting current total to 0.
5 Totalizer Register (total cumulative fluid dispensed).
6 Rate of flow being displayed.
7 Unit of measure (liters, gallons, quarts, pints).
1.3 USER BUTTONS
The face of the turbine digital meter has two buttons (MENU and RESET) which individually perform two main
functions and together, other secondary functions.
The main functions performed are:
For the reset key, resetting the partial Register and reset table total (reset total)
For the menu key, entering instrument calibration mode.
Used together, the two keys permit entering configuration mode.
1.4 BATTERY REPLACEMENT
The battery in your in-line digital meter is not replaceable. To minimize the possibility of fire or explosion, it is a
sealed unit that does not allow for user replacement. Do not attempt to open or replace the battery in your
meter.
2. INSTALLATION
The inlet and outlet for this meter is 1″BSP/NPT. It can be easily connected with the pipe or nozzle.
WARNING! Use of other fluids may be inaccurate and can damage the meter!
IMPORTANT! Not suitable for retail sale of diesel, oil, or kerosene!
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]

3. DAILY USE
3.1 BUTTON USAGE, CALIBRATION AND MEASUREMENT UNIT CHANGE
Reset the present total (See Fig. 2)
1) When the meter is in standby mode, press the RESET key.
2) The display shows all the segments at once.
3) The meter resets to display “0” on the resettable totalizer.
Show current correction factor and general total (See Fig. 3)
Press MENU and RESET together and hold for two seconds.
Value “1.4000” is the correction factor which can be reset;
“1234567” is the general total which cannot be reset.
Measurement unit change (See Fig. 4)
Press MENU and RESET together and hold for five seconds.
Zone 7 on the display is the current unit. Press RESET to chose a different measurement unit and then
press MENU to confirm.
3.2 RESET THE RESETTABLE TOTALIZER (SEE FIG. 5)
When the meter is in standby, press the RESET key for 2 seconds to reset the totalizer.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]

3.3 Calibration Procedure (Using the Correction Factor)
Carefully follow the procedure indicated below.
FORMULA
Proper correction factor = current correction factor× (actual value / display value)
Example:
Actualvalue 20.75
Displayvalue 18.96
Current correction factor 1.000
Proper correction factor 1.000×(20.75/18.96)=1.000×1.094=1.094
1 Wait for the meter to go into standby (blank screen).
2 With the meter in stand-by mode, reset the resettable
total by pressing the “RESET” button.
3 Press and hold the MENU key until the first digit in
the display begins to flash (approximately 5
seconds). The meter is in calibration mode.
4 Press the RESET key to choose the right digit from 0
to 9. Press the MENU key to start the next digit. So
the digit of correction factor can be changed one by
one.
5 Make sure the correction factor is right, press the
MENU key. Keep it pressed until quit calibration
mode, the factor is saved. The meter goes to standby
again.
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]

3.4 MODIFY THE CORRECTION FACTOR IN FIELD
PLEASE CAREFULLY FOLLOW THE PROCEDURE INDICATED BELOW.
1 Wait for the meter to go to standby.
2 Reset the resettable total.
3 Start dispensing into a measuring glass.
Stop dispensing when 5 Litres of volume is reached,
read out the actual value. The volume that is
displayed on the LCD is the Display Value, not the
Actual Value which may be slightly higher. For
example, in the figure on the right, the Display Value
is 18.96 while the Actual Value is 20.75.
4 Press the MENU key. Keep it pressed until showed
as the right fig., the digit flash in ①zone, Press the
RESET key to choose the right digit from 0 to 9.
Press the MENU key to go the the next digit so that
the Actual Value can be input.
5 Make sure the correction factor is right and then
press the MENU key. Keep it pressed until calibration
is finished and the factor is saved. The meter will
then return to standby.
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]

4. MALFUNCTIONS
Problem Possible Cause Corrective Action
LCD: no indication Bad battery contact Check battery contacts
Imprecise
measurement
Wrong FACTOR With reference to paragraph 3.3 & 3.4,
check the FACTOR
The meter works below
minimum acceptable flow rate
Increase the flow rate until an acceptable
flow rate range has been achieved
Reduced or zero
flow rate
Turbine blocked Clean the turbine.
The meter does
not count, but the
flow rate is correct
Incorrect installation of gears
after cleaning
Repeat the reassembly process.
Possible electronic card
problems
Contact Northern Tool + Equipment
5. DIAGRAM AND PARTS LIST
No Description Qty.
1 Meter Cover 1
2 Rubber Protection 1
3 Self-tap screw 2
4 Battery Holder 1
5 Electric Board 1
6 Battery CR2 1
7 Self-tap 3
8 Meter body 1
9 Bearing 2
10 Self-tap screw 4
11 Turbine 1
12 Bearing Holder 1
DC000440-000 Rev 0
mdi - Manufacturers Distributor Inc. | Phone: (813) 241 - 4900 | Fax: (813) 571 - 0422 | www.SoteraSales.com | [email protected]