FIMI X8 SE 2020 User manual

Please read the quick start manual carefully before using and keep it for future reference.
FIMI X8 SE 2020 Drone Quick Start Manual

Product Introduction
1 Drone
Integrated gimbal camera
Power button
Flight status lights
Reverse propeller
Battery level lightsPositive propeller

Drone tail light
Motor
Ultrasonic detecting module
Landing gear Optical flow camera
Battery buckle

Product Introduction
2 Remote controller
Power button
Auto take-off/land button
Auto return
Left stick
Stick storage slot
Five-directional button
Mobile device holder
Charging port
Right stick
Battery level lights
Cable slotUSB port

Right dialAntenna
Left dial Record button Shoot button

Function Introduction of RC
Note：The other functions of the five-directional button can be set in the FIMI Navi app.
Buttons Function description
Left stick
Push stick upward, the drone goes up; pull stick downward, the
drone goes down; toggle stick to left, the drone rotates counter-
clockwise; toggle stick to right, the drone rotates clockwise
Right stick Push stick upward, the drone flies forward; pull stick downward,
the drone flies backward; toggle stick to left, the drone flies to
left; toggle stick to right, the drone flies to right
Auto return
Five
directional
button
Toggle the button to the left, switching to normal flight
Toggle the button to the right, switching to auto return
Power button Short press to view the battery level
Short press+long press 2 seconds to power on / off
long press 2 seconds to auto take off/landing
Auto take-off/land button
short press to start / stop shooting
Shoot button
Short press to start /stop recording
Default to switch between map / FPV
Default to switch between gimbal center/down
Default to turn on / off battery info interface
Default to turn on / off self-checking interface
Default to turn on/off media library
Adjust the pitch angle of gimbal
Adjust the value of EV / ISO
Record button
Left dial
Right dial
Up
Down
Left
Right
Center
1
2
3
4
5
6
7
8
9
10

Forward
Drone heading
Up
Right
Down
Left
Backward
Up
Down
Forward
Backward
Counter-
clockwise
Clockwise Left Right
Note: The stick mode can be set in FIMI Navi app (the default is American hand).
Left stick Right stick

Basic Specification
Drone
Product model：FMWRJ03A6
Dimensions：204×106×72.6mm
Diagonal size：372mm
Take off weight：About 765g
Flight time：About 35min*
Max ascending speed：5m/s
Max descending speed：4m/s
Max flight speed：18m/s
Satellite positioning systems：GPS/GLONASS
Hover accuracy：
Vertical:±0.1m (Within the ultrasonic detecting range)
±0.5m (when GPS positioning is active) Horizontal: ±1.5m
Operating temperature：0°C ~ 40°C
Suitable altitude：≤5000m
Operating frequency：5.725-5.850GHz
Charger
Rated input：100-240V~50/60Hz 1.5A
Rated output：13.05V 3A
Rated power：39.15W
Remote controller
Net weight：About 373g
Dimensions：203.8×91×46.6mm
Operating frequency：5.725-5.850GHz
Type：Rechargeable lithium battery
Capacity：3900mAh
Nominal voltage：3.7V
Input：5 V 2A
Max transmission distance：About 8000m*
Operating temperature：0 ~ 40°C
Suitable altitude：≤5000m

Note：
The 35 minutes flight time refers to constant speed at 10m/s (no wind) with fully charged and low cyclic battery.
Remote control distance reach to 8km (FCC) in open area and no interference . All above testing and data come
from FIMI laboratory, errors may occur in actual use for operating and environmental changes.
Battery
Type：Rechargeable lithium battery pack
Weight：About 275g
Capacity：4500mAh
Voltage：11.4V
Limit voltage：13.05V
Energy：51.3Wh
Operating temperature：0°C ~ 40°C
Gimbal
Controllable rotation range：0°~ -90°（Pitch）
Angular vibration range：± 0.004°
Lens：FOV 79.5°
Camera aperture：f2.0
Camera focal distance：3.54mm
Equivalent focal distance：26mm
Sensor：1/3.06" CMOS
Effective pixels：12M
ISO range：100 - 3200
Shutter speed：32 ~ 1/8000s
Max video resolution：3840 x 2160 | 30fps | 25fps | 24fps
Max birate: 100Mbps
File system：FAT32 / exFAT
Image format：JPG，JPG+DNG
Video format：MP4
Memory card type：Micro SD ( U3 and above ) 8 ~ 256GB

Charging
1 Charge drone battery
Connect the battery,charger and AC cable as shown below, and plug the charger
into a power outlet.
When the battery is in charge, the battery level lights are flashing.
When the battery is fully charged, the battery level lights go out.
It takes about 2 hours to fully charge the battery.
100V ~ 240V

2 Charge RC
.
.
.
.
Connect the remote controller to a power adapter as show below.
When the RC is in charge, the battery level lights are flashing.
when the RC is fully charged, the battery level lights go out.
It takes about 2.5 hours to fully charge the RC in the powered off condition.
5V 2A

.
.
.
.
.
Assembly and Disassembly
1 Propellers
Unfold the front and rear arms of the drone.
Attach the gray marked propellers to the motor mounting base with gray marks on the arms.
Ensure the propeller is pressed to the bottom of the mounting base.
Rotate the propeller to the end of the lock direction until the propeller gets bounced and locked.
Press the propeller forcefully and rotate the propeller along the unlock direction to remove
the propeller.
Safety tips:
If the propeller is damaged, please replace them
to ensure flight safety and efficiency.Check if the
propeller is properly installed and fastened before
each flight.Stay away from the rotating propeller
to avoid cutting.
Note: Take the installation of reverse propeller as an example.

2 Drone TF card
When installing TF card to the drone,please unfold the arms of the drone first
and open the protective cover.
Insert the TF card with the literal upward into the TF card slot.
When removing TF card, press the TF card to pop out.
RC

.
.
3 Battery
Push hard the battery, after the battery installed in place, there will be a "click" sound.
To remove the battery, you need to press the battery buckle on both sides to pull out.

.
.
.
.
4 Remote controller
Tighten the mobile or pad on mobile device holder by extending the holder to the left.
Open the protective cover on the RC bottom.
Connect your phone and the RC with a USB cable.
Connect the drone and update firmware according to instructions in FIMI Navi app.
Note: The cable slot is reserved on the right .

.
.
.
Prepare to Fly
1 Confirm the drone heading
The direction of build-in gimbal is the drone heading.
Once the drone is turned on, the heading can be told by navigation lights.
The red light and the green light indicate the heading,and the yellow light is the tail.
Safety tips: Always keep the tail pointed at the user to avoid direction misjudging.
red green
yellow
Drone heading

.
.
2 Turning on/off the drone and the RC
Remote controller
Short press+long press power button 2 seconds to power on/off.
Short press to check battery level
Drone

Flying
1 Auto take-off/landing
Auto take-off Auto landing
The drone meets the auto take-off/landing condition when the auto take-off/landing
button light is white. Press this button for 2 seconds to auto take off/landing.
Left stick Right stick Left stick Right stick
2 Manual take-off/landing
Keep both sticks to the bottom inner still over 3 seconds, the propellers start spinning.
Release both sticks once propellers have been spinning, and firmly push the left stick
upward to take off the drone.
During flight, release both sticks to hover.
At any time during controlled flight, release the sticks and the drone will hover automatically.

Left stick Right stick
Slowly move the left stick downward to land the
drone.
Once the drone has landed, push and hold the
left stick down over 5 seconds, the motors will
stop.
Safety tips: The drone has no waterproof function. Please be careful of landing environment.
Do not land on an inclined plane for safety.

Safety tips: Do not do the above operation during normal flight to avoid motors being stopped in the air.
3 Stop propellers in an emergency
When motors can't properly turn off, please toggle the left stick to the bottom inner in
maximum range, and press Auto take-off/landing button for 5 seconds simultaneously,
the motors will stop.