Firecom 5000D Series User manual

1
2
3
4
5
6
7
8
9
10
Rx Tx
1
2
3
4
5
6
7
8
9
10
BACK OF INTERCOM
www.firecom.com
DIGITAL INTERCOM
QUICK REFERENCE
DOWNLOAD DETAILED PRODUCT MANUAL FROM WEBSITE
firecom.com/support
800.527.0555
17600 SW 65th Ave
Lake Oswego, OR 97035 USA
Copyright © 2019 Sonetics Corporation. All rights reserved.
600-1038-00 Rev E
LED COLORS
Aux Select
Incoming Traffic
Monitoring
Radio Select
Incoming Traffic
Outgoing Traffic
INTERCOM VOLUME INTERCOM SQUELCH
INPUT/OUTPUT GAIN ADJUSTMENT
1
HOLD BOTH BUTTONS
FOR 5 SEC UNITL
LEDS FLASH
2
PRESS BUTTON OF INPUT /OUTPUT TO ADJUST.
BUTTON LEDS WILL FLASH
3(INPUT) - ADJUST WITH VOLUME
BUTTONS HAVE A PARTNER SPEAK
INTO REMOTE RADIO
3(OUTPUT) - ADJUST WITH SQUELCH
BUTTONS HAVE A PARTNER LISTEN
TO REMOTE RADIO
4(INPUT) LISTEN TO HEADSET
AND ADJUST GAIN USING
VOLUME UP/DOWN
4(OUTPUT) SPEAK THRU HEADSET
TO REMOTE RADIO AND ADUST
USING SQUELCH UP/DOWN
5WHEN SATISFIED WITH AUDIO LEVEL,
HOLD FOR 5 SEC TO EXIT ADJUST MODE
WIRELESS BASE STATION SQUELCH ENABLE/DISABLE
1
HOLD BOTH SQUELCH
BUTTONS FOR 5 SECONDS
(RED LEDS FLASH)
2PRESS UP/DOWN VOLUME BUTTON
TO SELECT HEADSET
3
PRESS SQUELCH UP TO ENABLE
SQUELCH (RED LED ON)
PRESS SQUELCH DOWN TO
DISABLE SQUELCH (RED LED OFF)

2.58
0.81
7.13
3.07
GREEN
RED
BLACK
WHITE
YELLOW
BLUE
GND
BUSY -
DATA L
DATA H
POWER
BUSY +
TO REMOTE HEADTO INTERCOM
WHITE
BLACK
RED
GREEN
YELLOW
BLUE NOT USED
SPEAKER HI
SPEAKER LO
MIC HI
MIC LO
PTT
TO INTERCOM TO HEADSET MODULE
RJ-12 MODULAR PLUG RJ-12 MODULAR PLUG
4 3 2 1
Ground
Aux. In Low
Aux. In High
Aux. Out High
1
2
3
4
5
5 CONDUCTOR JACK
W/ GND RING
SPEAKER HIGH
SPEAKER LO
MIC HIGH
MIC LOW
PTT
BLACK
RED
GREEN
YELLOW
BLUE
WHITE
NOT USED
TO INTERCOM
5 CONDUCTOR PLUG
1
2
3
4
5
WHITE
BLACK
RED
GREEN
YELLOW
BLUE
WHITE
BLACK
RED
GREEN
YELLOW
BLUE NOT USED
SPEAKER HI
SPEAKER LO
MIC HI
MIC LO
PTT
4
3
2
1
5
TO INTERCOM
5 CONDUCTOR PLUG
1
2
3
4
5
TO DAISY CHAINED HEADSET
MODULE
www.firecom.com
DIGITAL INTERCOM
QUICK INSTALL & SCHEMATICS
REMOTE HEAD WIRING
PP-20 WIRING
HEADSET MODULE WIRING
WIRING SCHEMATICS
INTERCOM INSTALLATION
Mounting Flush to a Flat Surface
1. Remove the 4 Torx bolts (T-10) and nuts from the
corners of the remote head
2. Use the Remote Head as a template to mark and
drill (4) mounting holes: 7/64" diameter for sheet
metal screws or 5/ 32" for machine screws
3. Drill 3/8" hole in mounting surface and install the
supplied grommet. Pass the wire through
4. For inside installation, mount the panel using the
suppliedscrews (4), making sure the cable is not
pinched Recommended torque : 10 in-lbs
5. Determine the correct length for the CA cable,
and cut cable to correct length
Mounting with Bracket
1. Remove 4 Torx bolts (T-10) and nuts from the
corners of the remote head
2. Drill 3/4" hole at desired wire pass-through
location on mounting surface
3. Drill (4) mounting holes: 7/64" for #6 sheet metal
screws or 9/64" for #6 machine screws
4. Mount the bracket using included hardware.
Torque : 10 in-lbs
5. Pass cable through grommet and secure with
cable ties as shown
6. Adjust the panel to a desirable viewing angle with
the two hand knobs
1 2
PIN #2
RED
POWER CONNECTOR
ASSEMBLY
1.5 AMP FUSE
PIN #1 BLACK CLEAN WITH
WIRE BRUSH
CONNECT BLACK WIRE FROM PIN 1 TO VECHILES
NEGATIVE GROUND OR USE SUPPLIED SELF-TAPPING
SCREW & STAR WASHERS
REMOTE HEAD INSTALLATION
POWER CABLE CONNECTION
HEADSET MODULE WIRING
MR-OX
RADIO INTERFACE CABLE
HAND KNOB
CABLE TIES
GROMMET
#8 SHEET METAL SCREWS
USE 3/16” DRILL
MOUNTING BRACKET
AUX PLUG
PINOUT
PIN #1: BROWN - TX AUDIO HI
PIN #2: RED - TX AUDIO LO
PIN #3: ORANGE- PTT HI
PIN #4: YELLOW - PTT REFERENCE
PIN #5: GREEN - HOOK SWITCH RELAY (N.O)
PIN #6: BLUE - RX AUDIO HI
PIN #7: VIOLET - RX AUDIO LO
PIN #8: GRAY - HOOK SWITCH RELAY (N.C.)
PIN #9: BLACK - HOOK SWITCH RELAY (C.)