Firstech FTI-FDK1 User manual

FTI-FDK1 Type 1C4 - Vehicle Coverage & Preparation Notes
Make Model Year Install I/O Changes
DL-FM2
Ford Fiesta 2011-13 Type 1
CAN Lights RAP Trunk
Green White/BluePark / Auto
Hey! Read this stuff before you start the installation...
Firmware:
Covered vehicle uses BLADE-AL(DL)-FM2 firmware, flash module and update the controller firmware before installing.
Controller Configuration:
Set feature 1-11 to option 2 (Ignition pulse - same timing as disarm pulse) for proper handling of OEM alarm.
Door Locks:
Fiesta door locks are controlled by a single wire . Unlock is controlled by supplying a ( - ) negative pulse to the vehicle wire
(pin #8, brown/white, white 24-pin BCM connector), Lock is controlled by presenting an open circuit condition to the same wire.
See diagram below or in installation guide for detailed connection instructions.
Parking Lights:
Parking lights ( - ) negative: yellow/blue, pin #2 at headlight switch.
Lights-off (open): white/violet, pin #6 at headlight switch.
Okay, now get to work...
OBD-II C
CM-900
CM-900S/900AS
CM7X00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
SUPPORT - 1(888) 820-3690, EXT. 203
DEREK ZOOLANDER
Est. 2001
CENTER KIDS
WHO CAN’T READ GOOD
A
N
D
W
H
O
W
A
N
N
A
L
E
A
R
N
T
O
D
O
O
T
H
E
R
S
T
U
F
F
G
O
O
D
T
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
for
87a
87
30
FT-RLY-10A
brown/white
UNLOCK
10
25
6
Headlight Switch Connector
87a
87
30
FT-RLY-10A
+12V
yellow/blue
white/violet
PK LIGHTS
( - )
+12V
LOCK

A B C D E
A
B
C
D
DL-FM3 TX loop, not used in this install type, do not cut
Jumper for vehicles that are not equipped with immobilizer, do not connect unless vehicle is confirmed
not equipped. If vehicle is not equipped, connect before programming to skip immobilizer learn
Lock/unlock single wire control, unlock is ( - ) negative at 24-pin BCM connector (brown/white, pin #8),
lock uses a relay to open circuit, interrupt vehicle wire as shown in diagram [C] below
RAP control, cut driver door pin (pin#10, green/violet, GRAY 24-pin BCM connector, connect to
harness white/black and white/red wires. Trunk release green/white (pin #20, GRAY 24-pin at BCM)
EParking light ( - ) at 10-pin headlight switch connector, connect as indicated in diagram [E] below
(lights: pin #2, yellow/blue, lights-off: pin #6, white/violet)
1
2
3
4
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-FDK1 Type 1C4
3
4
FTI-FDK1 Type 1C4 - Installation Notes & Wiring Diagram
C
D
E
Module Programming Procedure
Step 1 - Key #1 in activate IGN, if LED goes blue, you’re done
if LED goes red, wait until flashes blue then key off/on
Step 2 - If LED goes blue, you’re done, if red, insert key #2
and activate IGN, when LED is red, remove key, press
module button, and remote start vehicle, blue/done.
**See BLADE guide for more detailed instructions
1
2
PWR
BLADE
Lock
1
16
LOCK/UNLOCK
TRUNK RELEASE
OBD-II Connector
Ignition switch
blue/black blue
white/black
white/red
DRIVER DOOR PIN
(+) PARKING LIGHTS
violet/white
LED Programming Error Codes
Module LED flashing RED during programming
1x - CAN error, check wiring
2x - VIN error, check CAN wiring
3x - Wrong firmware, confirm firmware flashed
4x - VIN error, vehicle not identified, contact support
5x - Immobilizer learn error, check RX/TX wiring
6x - KLON error, check RX/TX wiring, confirm pin positions
7x - KLON error, process failed, reset module and start over
8x - Encryption error, confirm key encryption, 80 bit detected
9x - Key in cylinder, remove and proceed
3
4
21
13
42
8
1021
13
2042
1
10
25
6
BCM
Headlight Switch
White
Gray
green/violet
87a
87
30
FT-RLY-10A
+12V
87a
87
30
FT-RLY-10A
+12V
green/white
green/white
yellow/blue
white/violet
brown/white
PK LIGHTS
( - )
A
B
C
E
BLADE
CUT FOR FM3
RAP
(+) PRK LT
FM4 LOCK
FM2/3
(+) PRK LT