Fisher & Paykel OR90SDBSIX2 User manual

Installation instructions
Please follow the installation steps below to ensure your appliance operates correctly.
Dimensions and clearances
• The cooker must be installed no less than 50 mm away from any side walls which exceed the height of the
cooktop.
• The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand
temperatures of 65 °C above room temperature.
• Do not install the cooker near flammable materials (eg curtains).
• If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
Locating the area for electrical connection
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
1

Fig. 1 Area for electrical connection
Fig. 2 Dimensions and distances from cooker
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
2

Levelling the cooker
Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate
ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface.
Fig. 3a Screw/unscrew the feet to get the required height
• For ease of installation, first remove the kickstrip. To remove the kickstrip, unscrew the two screws holding it in
place.
• The cooker is already fitted with four levelling feet.
• Level the cooker by screwing or unscrewing the feet.
• Make sure you follow the instructions in Figs. 3a, 3b, and 3c.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
3

Nuts are supplied with the cooker in a separate kit.
• Do not refit the kickstrip until you have installed the anti-tip bracket.
Fig. 3b Do not use the supplied nuts for height adjustments between 0 and 8mm
Fig. 3c Use the supplied nuts for height adjustments between 8 and 13mm
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
4

Fitting the anti-tilt bracket
To restrain the appliance and prevent it tipping accidentally, the antitilt bracket and restraining plate
supplied must be fitted according to the instructions below.
1. Drill four 8mm diameter holes for the fixing screws (two in the wall and two in the floor-see Fig.4) and insert the
plastic plugs supplied.
Fig. 4 Attaching the anti-tilt bracket and sliding the cooker into place
Before drilling the holes, check that you will not damage any pipes or electrical wires.
2. Attach the anti-tilt bracket to the floor and rear wall using the four screws supplied, as shown in Fig. 4.
3. After attaching the anti-tilt bracket securely, slide the cooker into place. Ensure that the left rear foot slides
under the bracket, as shown in Fig.4.
4. Access the bracket by removing the drawer (Fig. 5):
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
5

Fig. 5 Accessing the anti-tilt bracket by removing the drawer
a. Slide out the drawer completely.
b. Press the lever of the left guide rail down and pull the lever of the right guide rail up.
c. Holding the levers, disengage and remove the drawer.
5. If fitted, remove the kickstrip (see ‘Levelling the cooker’). Fix the restraining plate by sliding it into place and
securing it with the fixing screw and washer supplied. See Fig. 6.
Fig. 6 Fixing the restraining plate
6. Replace the drawer (Fig. 7):
Fig. 7 Replacing the drawer
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
6

a. Insert the drawer rails into the guide rails.
b. Gently push the drawer in completely; the safety catches will automatically hook.
7. Replace the kickstrip using the two screws.
Beware of sharp edges when removing or replacing the drawer.
Moving the cooker
To prevent damaging the adjustable feet or lower trim, ensure the cooker is always lifted by two
people.
Do not lift the cooker by the door handles. DO NOT DRAG the cooker. Lift the feet clear of the floor.
Fig. 8 Correctly lifting the cooker.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
7

Fig. 9 Incorrectly lifting the cooker. Fig. 10 Incorrectly moving the cooker
Fixing the backguard
Before installing the cooker, assemble the backguard “C” .
• The backguard “C” can be found packed at the rear of the cooker.
1. Before assembling, remove any protective film/adhesive tape.
2. Remove the two spacers “A” and the screw “B” from the rear of the cooktop.
3. Assemble the backguard as shown and fix it by screwing the central screw “B” and the spacers “A”.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
8

Fig. 11 Assembling the backguard
Connecting the power supply cable
This cooker must be connected to the electricity supply only by an authorised person.
To connect the power supply cable to the cooker, it is necessary to:
1. Unhook the terminal board cover by inserting a screwdriver into the two hooks ‘A’ (fig. 12).
2. Unscrew the screw ‘D’ and open completely the cable clamp ‘E’ (figs. 14).
3. Position the U bolts ‘F’ onto terminal board ‘G’ (figs. 14) according to the diagrams in fig. 13.
4. Connect the phase, neutral and earth wires to terminal board ‘G’ according to the diagrams in figs. 13 - 14.
5. Strain the feeder cable and block it with cable clamp ‘E’ (by screwing screw ‘D’).
6. Close the terminal block cover (check the two hooks ‘A’ are correctly hooked).
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
9

To connect the power supply cable DO NOT unscrew the screws fixing the cover plate behind the
terminal block.
If the power supply cable is damaged, it must be replaced only by an authorised service
agent in order to avoid a hazard.
Voltage and power consumption
220-240/380-415 V 3N~ 50/60 Hz 48, 17 A (230 V) 11080W (diversity not applied)
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIX2/User_Guide_OR90SDBSIX2/02_Installation_instructions
Updated: Fri, 08 Mar 2019 10:03:53 GMT
Powered by
10