Fisher & Paykel CE604DT User manual

Installation instructions
Please read and follow the ‘Safety and warnings’ and ‘installation instructions’ sections carefully before using your
cooktop!
Cooktop and cutout dimensions
Property CE604DT CE704DT CE754DT
AOverall width of cooktop (mm) 600 700 750
B Overall depth of cooktop (mm) 530 530 530
CHeight of chassis (below top of bench)(mm) 48 48 48
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
1

Property CE604DT CE704DT CE754DT
C1Height of terminal block (below top of bench)(mm) 58 58 58
D Width of chassis (mm) 552 552 715
E Depth of chassis (mm) 480 480 480
F Overall width of cutout (mm) 560 560 725
G Overall depth of cutout (mm) 490 490 490
Clearances
Property CE604DT CE704DT CE754DT
AMinimum clearance from rear edge of cutout
to nearest combustible surface (mm).
55 55 55
BMinimum clearance from glass surface
to rangehood (mm).
650 650 650
CMinimum clearance from side edges of cutout
to nearest combustible surface (mm).
85 135 78
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
2

Property CE604DT CE704DT CE754DT
DMinimum clearance from benchtop to overhead
cabinet not directly above the cooktop (mm).
450 450 450
EMinimum clearance below top of benchtop
to thermal protection barrier (mm).
68 68 68
Before you install the cooktop, make sure that
• the benchtop is square and level, and no structural members interfere with space requirements the benchtop is
made of a heat-resistant material
• the cooktop will not be installed directly above a dishwasher, as the humidity may damage the cooktop
electronics
• the installation will comply with all clearance requirements and applicable standards and regulations
• a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the
permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The isolating
switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active
[phase] conductors if the local wiring rules allow for this variation of the requirements)
• the isolating switch will be easily accessible to the customer with the cooktop installed
• you consult local building authorities and by-laws if in doubt regarding installation
• you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding the
cooktop.
When you have installed the cooktop, make sure that
• the power supply cable is not accessible through cupboard doors or drawers
• there is adequate flow of fresh air from outside the cabinetry to the base of the cooktop
• if the cooktop is installed directly above an oven or its base is accessible through a cupboard or drawer space
after installation, a thermal protection barrier is installed below the base of the cooktop (see Fig.1)
• the isolating switch is easily accessible by the customer
• you complete the ‘Final checklist’ at the end of these installation instructions.
The thermal protection barrier must be:
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
3

• removable
• heat-resistant
• made from low thermal conductivity material
• at least 20 mm below the base of the cooktop to
ensure adequate ventilation
Fastening the cooktop to the bench
1. Turn the cooktop upside down and place it on a soft surface.
2. Spread the seal around the edges of the ceramic glass with the adhesive side facing down, making sure that
the whole perimeter is sealed. Cut off any excess material.
3. Mount the supplied clamps (A) and screws (B) onto the cooktop, as shown (without tightening the screws).
4. Place the cooktop into the cutout, then tighten the screws to clamp the cooktop securely to the bench.
5. Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the cooktop. Take
care not to damage the benchtop.
If your bench is thicker than 40 mm, recess the underside to between 30 and 40 mm.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
4

Connecting the cooktop to the mains power supply
• This cooktop must be connected to the mains power supply only by a suitably qualified person.
• This cooktop must be earthed.
• Before connecting the cooktop to the mains power supply, check that:
1. the domestic wiring system is suitable for the power drawn by the cooktop
2. the voltage corresponds to the value given on the rating plate
3. the power supply cable sections can withstand the load specified on the rating plate.
• To connect the cooktop to the mains power supply, do not use adapters, reducers, or branching devices, as they
can cause overheating and fire.
• The power supply cable must not touch any hot parts and must be positioned so that its temperature will not
exceed 75°C at any point.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
5

Power Supply
CE604DT 6400W @ 220-240/380-415V 2N~ (28A)
CE704DT 6400W @ 220-240/380-415V 2N~ (28A)
CE754DT 7300W @ 220-240/380-415V 2N~ (32A)
Connecting Diagrams
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Four_Burners/CE754DTB1/User_Guide_CE754DTB1/02_Inst…
Updated: Sat, 15 Feb 2020 13:29:47 GMT
Powered by
6