Fisher & Paykel CI804CTB User manual

Using your induction cooktop
CI604CTB model
CI704CTB model
CI804CTB model CI904CTB model
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
1

Cooking Zone Zone Diameter Power Powerboost Recommended Minimum Pan Size
1200 mm 2300 W 3000 W * 145 mm
2160 mm 1200 W 1400 W * 110 mm
* Maximum output when set on PowerBoost.
Touch controls overview
These indicators show which cooking zone(s) the timer is set for:
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
2

To select a setting on the selector:
Touch at one point to “jump” to a specific setting
OR
slide your finger along the selector.
To start cooking
1. Touch and hold the ON/OFF control for 2 seconds.
• a red indicator light will glow.
2. will appear in the cooking zone displays.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
3

3. Place a suitable pan on the cooking zone you wish
to use.
• Make sure the bottom of the pan and the surface
of the cooking zone are clean and dry.
Always place small pans in
the centre of the cooking
zone.
4. Touch the display of the cooking zone you wish to
use.
6. You can modify the heat setting at any time during
cooking.
• Touch the display of the cooking zone you wish
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
4

5. Select a heat setting by touching or sliding the
setting selector with your finger.
• The setting will appear in the display of the
selected cooking zone.
• If you don’t choose a heat setting within 20
seconds, the cooktop will automatically turn off.
Start with step 1 again.
to adjust.
• Adjust the heat setting by touching or sliding the
setting selector with your finger.
• The new heat setting will appear in the display of
the selected cooking zone.
If a display flashes
alternately with the heat setting
This means that:
• you have not placed a pan on the correct cooking
zone or
• the pan you’re using is not suitable for induction
cooking or
• the pan is too small or not properly centred on the
cooking zone.
• No heating takes place unless there is a suitable pan
on the cooking zone.
• The cooktop will automatically turn off after 10
minutes if no suitable pan is placed on it.
When you have finished cooking
To turn off an individual cooking zone, but continue to use other cooking zones
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
5

1. To turn off an individual cooking zone
Select the cooking zone you want to turn off.
2. Decrease its heat setting until the display shows
. If the cooking zone surface is too hot to touch,
will replace
in the display.
To turn the whole cooktop off
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
6

Turn the whole cooktop off by touch and holding the ON/OFF control.
Beware of hot surfaces
will appear in the display of any cooking zone that is too hot to touch. It will remain on and steadily lit even when
the cooktop is turned off. It will disappear when the surface has cooled down to a safe temperature.
Locking the controls
• You can lock the controls to prevent unintended use
(for example children accidentally turning cooking zones on).
• When the controls are locked, all controls except the ON/OFF control are disabled.
To lock the controls
1. Make sure that the cooktop is turned on but no cooking zone is in use.
2. Touch and hold the keylock control for a few seconds. The indicator light above the control comes on,
indicating that the controls are locked.
The cooktop will automatically turn off after 20 seconds, but the controls will still be locked
when you turn the cooktop on again.
If any controls are accidentally touched while the cooktop is locked the white ‘lock’ indicator light will flash and the
cooktop will remain locked.
To unlock the controls
1. Make sure the cooktop is turned on.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
7

2. Touch and hold the keylock control
for a few seconds. The indicator light above the control goes out.
3. You can now start using your cooktop.
Do not lock the controls while a cooking zone is in use. If you do, you can always turn the
cooktop off with the ON/OFF control in an emergency.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Induction/Four_Burners/CI904CTB1/User_Guide_CI904CTB1/04_Usi…
Updated: Sun, 16 Aug 2020 01:40:18 GMT
Powered by
8