Fisher-Price Healthy Care B8866 User manual

www.fisher-price.co.uk
B8866
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.

2
Prevent serious injury or death from falls
or sliding out:
• The child should at all times wear a safety
harness correctly fitted and adjusted. The tray
is not designed to hold the child in the chair.
• It is recommended that only children capable
of sitting upright unassisted use the high
chair in the upright position.
• Always keep child in view while in the
high chair.
• Never leave child unattended.
• Do not use the high chair unless all compo-
nents are correctly fitted and adjusted.
Prevent injury from burns: Do not place this
high chair near open fires or any hot surfaces.
WARNING
CAUTION
This package contains small parts in its
unassembled state. Adult assembly is required.
2
Consumer Information
IMPORTANT! Place the high chair on a level, stable surface away
from electrical flexes. Be sure to keep electrical flexes out of
child's reach.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tool needed for assembly: Phillips screwdriver (not included).
• Product features and decorations may vary from photographs.
• GREAT BRITAIN
Mattel UK Ltd,Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303; www.service.mattel.com/uk.

3
Parts
2 Bases Footrest
2 Frames
Hinge Rod
2 Seat Bottom Tubes
Pad Seat Bottom
Seat Back
Base Tray
Food Tray Teether Toy
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
Shown Actual Size
#8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7

4
1
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Assembly
Seat Bottom
Footrest
• Slide a seat bottom tube through each set of plastic rings on the
seat bottom.
2
Plastic Rings
Seat Bottom Tubes
Plastic Rings
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed.
Never substitute parts.
• Align the holes in the plastic rings and the seat bottom tubes.
• Insert a #8 x 1,9 cm screw through each plastic ring and into the
seat bottom tubes, as shown.Tighten the screws.This may require
extra force.
• Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you have
probably not fastened them properly. Remove the screws and check
to be sure the screw holes in the seat bottom tubes and seat bottom
plastic rings are aligned. Replace and tighten the screws.
3

5
Assembly
4
• Insert two #10 x 2,2 cm black screws through the footrest
and into the seat bottom.Tighten the screws.This may require
extra force.
Insert Screws Here
5
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the slots in the top side of the seat
bottom assembly.
6
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back and seat
bottom, as shown.
• Insert a #10 x 2,2 cm black screw into the hinge rod.Tighten
the screw.
• Set the seat assembly aside for Assembly step 9.
Hinge Rod
Hinge
Seat Bottom
Assembly
Seat Back
Pin Seat Back
Pin
Slot Slot

6
7
Assembly
• Pull the frame leg out on each frame to open. Make sure it "clicks"
into place.
• Position a frame so that the decorated side is outward.
• Fit the end of a base into the back leg of a frame.
• Fit a screw retainer over the hole in the back leg, as shown.
• Insert a #10 x 2,2 cm black screw through the screw retainer and
back leg.Tighten the screw.
• Repeat this procedure to fasten the other frame back leg to the
other side of the base.
Hint: The #10 x 2,2 cm black screws may have been assembled to
the screw retainers.
Frame Decorated Side
Frame Back Legs
Base
Screw Retainers
Frame Leg
8
• While pressing the levers on the seat height adjusters, lift them to
position 4 on the frame front legs, as shown.
Seat Height Adjusters
Position 4
Press Lever
4
9
• Fit the seat assembly between the frames.
• Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
• Be sure the seat height adjusters are in the same position
(position 4).
• You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
Seat Assembly
Seat Bottom
Tubes
Sockets Sockets

7
Assembly
10
Base
• Insert the frame front legs onto the remaining base.
• Fit a screw retainer over a hole in the front leg.
• Insert a #10 x 2,2 cm black screw through the screw retainer and
front leg.Tighten the screw.
• Repeat this procedure to secure the other end of the base with the
remaining screw retainer and #10 x 2,2 cm black screw.
Hint: The #10 x 2,2 cm black screws may have been assembled
to the screw retainers.
Screw Retainers
11
• Push each seat height adjuster to be sure they are completely on the
seat bottom tubes.
• Insert a #8 x 1,9 cm screw through each seat height adjuster and the
ends of the seat bottom tube.Tighten the screws.This may require
extra force.
Seat Bottom
Tube Ends
Push Push

8
Assembly
12
• Push each seat height adjuster to be sure they are completely on the
seat bottom tubes.
• Insert a #8 x 1,9 cm screw through each seat height adjuster and the
ends of the seat bottom tube.Tighten the screws.This may require
extra force.
• Lift the assembly upright.
• From the front of the assembly, place the pad onto the seat.
• Lift the bottom of the pad. Insert the two elastic loops on the pad
through the holes in the seat bottom.
• From the back and bottom of the seat, hook the elastic loops to the
tabs on the seat.
Pad
Hole
Hole
Elastic Loops
Tabs
Elastic Loops
13
Seat
Height
Adjuster
Seat
Height
Adjuster
Seat
Bottom
Tube Ends

9
Assembly
• Insert the crotch belt through the slot in the pad. Make sure the
crotch belt is not twisted.
Crotch
Belt
Slot
• Fold the top of the pad down.
• Remove the shoulder portion of the waist/shoulder belts by
feeding them through the slots in the seat back.
Shoulder
Portion
• Lift the top of the pad.
• Thread the waist/shoulder belts through the bottom slots in the
back of the seat pad.
Bottom Slots
14
15
16

10
Assembly
• Insert the shoulder portion of the shoulder/waist belt
through the slots in the pad and seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
• Fit the top of the pad over the seat back.
• Fold the bottom edge of the pad under the edge of the
seat bottom to fasten.
Lower Shoulder
Belt Slots
Upper Shoulder
Belt Slots Shoulder Portion
17
Assembly is now complete.
• From behind the seat, be sure the shoulder portion of the
waist/shoulder belts are secure in the seat back slots.
• Fit the pad strap through the handle and press it to the
fastener on the back of the seat.
• Hook the elastic loops on each side of the pad onto the
tabs in the seat back.
Elastic
Loop
Pad Strap
Handle
Elastic
Loop
Tab
Tab Belt
Ends
18