Fisher-Price LEARNING PATTERNS Play Dome User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Play Dome
Product features may vary from picture above.
Model Number: B0003
Please keep this instruction sheet for future reference, as it contains important information.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
L
E
A
R
N
I
N
G
P
A
T
T
E
R
N
S
L
E
A
R
N
I
N
G
P
A
T
T
E
R
N
S
™

Failure to follow these warnings
and instructions could result in
serious injury or death.
To reduce the risk of Sudden Infant
Death Syndrome (SIDS), normal
healthy infants should always sleep
on their backs unless otherwise
advised by a pediatrician.
• Infants can suffocate:
-In gaps between an extra pad and
side of the dome.
-On soft bedding.
• Never add a mattress, pillow,
comforter or padding. Use ONLY the
pad provided by the manufacturer.
• To prevent falls:
-Do not use this product when
infant begins to push up on hands
and knees.
-Never place product on an
elevated surface.
• To prevent strangulation:
-Never place items with strings,
such as hood strings or pacifier
cords, around a child's neck.
-Never place product near a
window where cords from blinds
or drapes can strangle a child.
• Never move this product with
child in it.
• Never leave child unattended.
WARNING
2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price® Consumer Relations, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont
Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Consumer Information
Warnings

Parts
Base
Pad
Metal Stay
3 Toys
(Toys may be different than shown.)
2 Base Wires
®
®
2 Covers
Plastic Stay
All Shown Actual Size
M4 x 113/16" Screw - 2
M5 Lock Nut - 8
(Inside Base Frames)
M5 x 15/8" Screw - 8
M4 Lock Nut - 2
(Inside Base Frames)
Spring - 4
3

Assembly
IMPORTANT! Before each use or assembly, inspect this
product for damaged hardware, loose joints, missing parts
or sharp edges. DO NOT use if any parts are missing or
broken. Contact Fisher-Price® for replacement parts and
instructions if needed. Never substitute parts.
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
• Open the base and position it upright on a flat surface,
as shown.
• Locate the end of the base with the mesh cover. Insert the
entire plastic stay into one of the button holes in the
mesh cover.
• Be sure to tuck the plastic stay away from the button hole
in the mesh cover.
1
• Insert the metal stay through the canopy tunnel.
4
2
• Position the ends of the frame tubes against the middle
holes in a frame.
3
Base
Mesh Cover
Button Hole
Plastic Stay
Metal
Stay
Canopy Tunnel
Frame Tubes
Frame Middle Hole Frame Middle Hole

4
5
Assembly
• Insert an M5 x 15/8" screw through each frame tube and
into the middle hole in the frame with lock nuts.
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat assembly steps 3 - 5 to attach the other ends of
the frame tubes to the frame on the other side of the base.
Shown Actual Size
M5 x 15/8" Screw - 4
M5 Lock Nut (Inside Frame) - 4
Rounded
Side
Hint: Lock nuts have been factory assembled to the frame.
During shipment, the lock nuts may have fallen out of the
frame. If this has happened, please fit the lock nuts back into
the middle hexagonal holes in the frame, so that the rounded
side of the lock nuts face out.You may find it easier to access
the hexagonal opening on the back of the frame if you push
the base up, so that the fabric is out of the way.
Frame Tube
Frame Tube
Frame with
Lock Nuts
5

6
Assembly
7
Hint: Lock nuts have been factory assembled to the frame.
During shipment, the lock nuts may have fallen out of the
frame. If this has happened, please fit the lock nuts back into
the lower hexagonal holes in the frame, so that the rounded
side of the lock nuts face out.You may find it easier to access
the hexagonal hole on the back of the frame if you push the
base up,so that the fabric is out of the way.
Shown Actual Size
M5 x 15/8" Screw - 4
Base Wire
Frame
Lower Hole
Spring
Frame with
Lock Nuts
6
• Position the base wires around the base so that the ends
point upward and are against the lower holes in a frame.
• Place a spring onto an M5 x 15/8" screw.
• Insert the M5 x 15/8" screw with spring through a base wire
and into the lower hole in the frame with lock nuts.
Spring - 4
M5 Lock Nut (Inside Frame) - 4
Rounded
Side
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the
base wires to the frame with lock nuts on the other side
of the base.
Base
Wire
Spring
Frame
Lower
Hole

7
Assembly
9
8
Upper
Hole
Cover
Slot Tab
Metal Stay
Shown Actual Size
M4 x 113/16" Screw - 2
M4 Lock Nut (Inside Frame) - 2
Rounded
Side
• Position one end of the metal stay against the upper hole
in a frame.
• Insert an M4 x 113/16" screw through the hole in the cover.
• Fit the end of the screw through the hole in the metal stay,
the upper hole in the frame and into the lock nut.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the metal
canopy stay and the remaining cover to the frame on the
other side of the base.
Hint: A lock nut has been factory assembled to the frame.
During shipment, the lock nut may have fallen out of the
frame. If this has happened, please fit the lock nut back into
the upper hexagonal hole in the frame, so that the rounded
side of the lock nut faces out.You may find it easier to access
the hexagonal hole on the back of the frame if you push the
base up,so that the fabric is out of the way.
®
Pad
Fastener
• Fasten the pad fasteners to the base fasteners.
IMPORTANT! Assembly is now complete, but Bounce ‘n Play
Activity Dome is NOT ready for use. Please refer to the
Set-Up & Use instructions beginning with step 2.
• Push on the cover to insert and “snap” the tab on the cover
into the slot in the frame. Make sure you hear a “snap”.

8
• Position the product upright on a flat surface.
• Grasp both sides of a base wire. Pull both sides of the base
wire outward and then let the base wire rotate down.
Note: If the base wire does not freely rotate down, pull the
sides of the base wire further outward.
Set-Up & Use
To Unfold
Sides of Base Wire
1
Sides of Base Wire
2
Frame
Groove Groove
3
Base Wire
Groove
Frame
PUSH PUSH
• Push down on the product to
be sure each side of the base
wire is in the correct position.
The base wire should rest in
the groove in each frame.
• Repeat Use steps 1- 3 to
unfold the other base wire.
• Lift the product up slightly so that each side of the base
wire “snaps” into the groove in each frame. Make sure
you hear a “snap”.
CORRECT

9
®
4
Using the Canopy
• Adjust the canopy up or down.
Canopy
Down
Canopy Up
Set-Up & Use
Using the Mesh Cover
®
5
Canopy Up
Mesh Cover Up
Zipper
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the zipper closed.

10
®
6
Set-Up & Use
• Fit the canopy strap through the
slot in the toy ring. Fasten the strap.
• Or, attach the toys to the straps inside the dome
(see step 7).
Hint: Pull the lion’s head for a short tune.
®
7
• Fit a strap inside the dome
through the slot in the toy ring.
Fasten the strap.
• Or, attach the toys to the straps
on the canopy (see step 6).
Hint: Pull the lion’s head for a short tune.
Canopy Strap
Strap

11
Set-Up & Use
9
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
Base Wire
8
To Fold for Portability
Frame
Groove Groove
Sides of Base Wire
• Grasp both sides of a base wire.
• While lifting the product up slightly, pull both sides of
the base wire outward to remove the base wire from the
groove in each frame.

12
FCC Note (United States Only)
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user‘s authority to operate the equipment.
Care
The pad is machine washable.Wash the pad separately in
cold water on the gentle cycle. Do not use bleach. Tumble
dry separately on low heat and remove promptly.The fabric,
frame and toys may be wiped clean using a mild cleaning
solution and a damp cloth.
Note: Do not dispose of the musical toy in a fire. The
battery(ies) inside the toy may explode or leak.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China B0003pr-0920