Fisher-Price 74924 User manual

Model Number 74924
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).

Parts
Base
Base Extension
Basket
Oven Panel Oven Dial
Arch
Shelf
FaucetFaucet Handle
Front Panel
Freezer Shelf
Side Panel
with Molded
Puppy
Side Panel Back Panel
Countertop
Oven Door
Refrigerator Door Side Table
Sink
Phone
#8 x 3/4" Screw - 34
Shown Actual Size
Parts Not Shown:
Label Sheet
Spatula
Frying Pan
4 Cookies
Teapot with Lid
Sugar Bowl
Creamer
Serving Tray
4 Saucers
4 Spoons
4 Tea Cups
2
Side Table Support

CAUTION
This product contains small parts
in its unassembled state.
Adult assembly is required.
Assembly
Bottom View
Base
Base
Extension
Tabs
Slots
• Place the base upside down on a flat surface.
• Place the base extension on the base so that the tabs
on the base fit into the slots in the base extension.
• Push down on the base extension to “snap” it in place.
1
1
3
3Side Panel
Oven
Ribs
Refrigerator
Openings
Side Panel with
Molded Puppy
Front Panel
3
• Turn the base upright.
• Insert two screws through the holes in the base and into
the base extension. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
2
2
• Place the front panel face down on a flat surface.
• Position the side panel with the molded puppy with
the decoration facing outward. Fit the side panel
with the molded puppy to the front panel near the
refrigerator openings.
• Insert four screws through the holes in the side
panel with the molded puppy and into the front
panel. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Position the other side panel so that the ribs face
inward. Fit the side panel to the front panel near
the oven.
• Insert four screws through the holes in the side panel
and into the front panel. Tighten the screws with a
Phillips screwdriver. Do not over-tighten.
Base

4
4
Assembly
Front Panel
Groove
Freezer
Shelf
Side Panel
with Molded
Puppy
5
5
Refrigerator Opening
Refrigerator
Coils
Side Panel
Back Panel
• Position the back panel with the molded detail
upright. Make sure the refrigerator coils are over
the refrigerator openings.
• Fit the back panel onto the side panels.
6
6
Side Panel
Back Panel
• Insert eight screws through the back panel and into
the side panels. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
7
7
Base
• Position the assembly over the base, as shown.
• Insert and “snap” the tabs on the bottom of the
assembly into the slots in the base.
• Slide the freezer shelf into the grooves in the side
panel with the molded puppy and the front panel.
4
Groove
Side Panel

8
8
Assembly
Countertop
Refrigerator
Openings
Sink
Opening
• Position the countertop so that the sink opening is
above the refrigerator openings. Fit the countertop
to the assembly.
9
9
• Insert ten screws up through the front, back and side
panels and into the countertop. Tighten the screws
with a Phillips screwdriver. Do not over-tighten.
Hint: You may find it easier if you tip the assembly
first backward and then forward to tighten the screws.
Side Table
Support
Side Table
Groove
Peg
• Place the side table down on a flat surface.
• Fit the grooves in side table support onto the pegs
on the side table.
• Insert two screws into the pegs in the side table.
Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
11
11
Side Table
Assembly
Base
Extension
• Position the side table assembly at an angle, as shown.
• Insert and “snap” the tabs on the bottom of the side
table assembly into the slots in the base extension.
• Insert and “snap” the remaining tabs on the side table
assembly into the slots in the side panel.
Groove
Peg
5
10
10