Fisher-Price ESPN FAST ACTION FOOTBALL User manual

1
ASSEMBLY
J7512
CAUTION - ELECTRIC TOY
Not recommended for children under
6 years of age. As with all electric
products, precautions should be
observed during handling and use
to prevent electric shock.
PRINTED IN CHINA J7512pr-0920

CONSUMER INFORMATION
General
• Please keep this instruction sheet for future reference, as it contains
important information.
• Adult assembly is required. Tool needed for assembly:
Phillips screwdriver.
• If you experience a problem, or are missing a part, please call us at
1-800-432-5437 rather than return this product to the store. Or, visit
us on-line at www.fisher-price.com.
• Call Fisher-Price® Consumer Relations between 9 AM – 7 PM (EST)
Monday through Friday or 11 AM – 5 PM (EST) Saturday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470.
Write to us at: Fisher-Price, Inc., Consumer Relations, 636 Girard Avenue,
East Aurora, New York 14052.
6V AC Adaptor
• Requires a 6V AC adaptor (UL listed Class 2 Toy Transformer; 120VAC, 6VDC,
2.5 amp) for operation (included).
• Always use this toy where there is adequate ventilation. To prevent
overheating, keep this toy away from heat sources such as radiators,
heat registers, direct sunlight, stoves, amplifiers or other appliances
that produce heat.
• Use the 6V AC adaptor only in a wall outlet. Do not plug the adaptor into
a ceiling outlet.
• Never use extension cords with the 6V AC adaptor.
• Never use this toy near water (ie.: bathtub, sink, laundry tub or wet
basement, etc.).
• Adults Note: Regularly examine the 6V AC adaptor for damage to the cord,
plug, enclosure or other parts that may result in the risk of fire, electric
shock or injury. If the 6V AC adaptor is damaged, do not use this toy.
• Do not connect to more than the recommended number of power supplies.
• This toy must only be used with the recommended 6V AC adaptor.
• The 6V AC adaptor is not a toy.
• Disconnect the 6V AC adaptor from the toy before cleaning.
• This toy is intended for use for children 6 years to adult.
2

PARTS
Table Top
2 Braces
2 Grandstands
Please identify all parts before assembly and save all packaging material
until assembly is complete to ensure that no parts are discarded.
This product contains small parts in its
unassembled state. Adult assembly is required.
CAUTION
2 Legs with
Connectors
2 Legs
4 Retainers
(2 Lefts, 2 Rights)
3
2 Connector
Covers

PARTS
6V AC Adaptor
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten.
All Fasteners Shown Actual Size
M4 x 22 mm Black Screw - 22
2 Joysticks 2 Footpads
2 Goal Posts
M6 x 62 mm Screw - 4
4
M5 x 22 mm Screw - 8

ASSEMBLY
• Position the table top upside down on a flat surface.
Hint: You may want to place a blanket on the surface to protect the
table top.
• Fit the retainers into the sockets in the table top.
Hint: The retainers are designed to fit into the table top one way.
If a retainer does not seem to fit into a socket, try another socket!
Retainers
l
5
Retainers
Table Top

ASSEMBLY
• Slide a leg with a connectors, flat side first, into a retainer that is next
to a connector.
Hint: The connectors on the table top are diagonal from each other.
Retainer
2
Leg with Connectors
6
Connector
Connector

ASSEMBLY
• Feed the wire on the leg under the arch in the retainer.
• Fit the connector on the end of the wire out through the slot in
the retainer.
3
7
Arch
Connector
Slot

ASSEMBLY
• Plug the connector from the leg into the connector on the table top.
• Tuck the connectors into the pocket in the table top.
4
8
Pocket

ASSEMBLY
• Fit the connector cover over the pocket.
• Fit the connector wire into the groove in the connector cover.
• Insert an M4 x 22 mm black screw into the connector cover and tighten.
• Repeat Assembly Steps 1- 5 to attach the other leg with connectors
to the other retainer (next to a connector); make the connector
connection and assemble the remaining connector cover.
5
9
Connector Cover

ASSEMBLY
• Fit the two remaining legs, flat end first into the openings in
the retainers.
6
10
Legs

ASSEMBLY
• Insert two M5 x 22 mm screws through the leg and into the table top,
as shown. Tighten the screws.
7
11

ASSEMBLY
• Insert an M4 x 22 mm black screw through each retainer and into the
table top, as shown. Tighten the screw.
• Insert an M4 x 22 mm black screw through each side of the table top
and into the retainer, as shown. Tighten the screw.
8
12

ASSEMBLY
• Fit a brace to the leg assemblies on one end of the table top.
• Insert four M4 x 22 mm black screws through the retainers
and into the brace. Tighten the screws.
• Repeat this assembly step to assemble the other brace.
Brace
9
13

ASSEMBLY
• Locate the connector extending from one side of each footpad.
• Plug the footpad connector into the connector extending from two of
the legs. Tuck the excess wire down into each leg.
• Now, fit the footpads onto the legs.
Footpad
Footpad
l0
14

ASSEMBLY
• Insert an M6 x 62 mm screw through the hole in the side of each foot-
pad and through the leg. Tighten the screws.
• Turn the assembly upright.
l l
15

ASSEMBLY
• “Snap” both grandstands to the table top.
Hint: The grandstand with the cut-out attaches to the scoreboard side
of the table top.
Cut-Out
Scoreboard
l2
16
Grandstands

ASSEMBLY
• “Snap” both goal posts into the holes on each end of the field in the
table top.
Goal Post
l3
17
Goal Post

ASSEMBLY
Hint: The joystick base and joystick are designed to be assembled one
way. Attach the red joystick to the red joystick base and yellow joystick
to the yellow joystick base.
• After attaching the joysticks to the joystick bases, insert two
M4 x 22 mm black screws into each joystick base. Tighten the screws.
Joystick
l4
18
Joystick
Base

• Locate the AC adaptor socket on the underside of the table.
• Fit the 6V AC adaptor pin into the socket.
• Plug the 6V AC adaptor into a standard wall outlet.
Note: Use the AC adaptor only in a wall outlet. Do not plug the
AC adaptor into a ceiling outlet.
ASSEMBLY
AC Adaptor
Socket
l5
19

• This toy is not intended for use outdoors.
• Wipe this toy with a clean cloth dampened with a mild soap and
water solution. Wipe clean to remove soap residue.
• Do not immerse this toy.
• Keep this toy away from direct sunlight and excess heat.
CARE
20
(UNITED STATES ONLY)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufac-
turer responsible for compliance could void the user's authority to operate
the equipment.
FCC STATEMENT