Fisher-Price SUPER SOUNDS SOCCER L5805 User manual

1
www.fisher-price.com
www.fisher-price.com
Model L5805
Super Sounds
Super Sounds
Soccer
Soccer
Super Sounds
Super Sounds
Soccer
Soccer
Super Sounds
Super Sounds
Soccer
Soccer ™

2
Ball
Pin
2 Tubes with Tapered Ends
(Upper and Lower)
Tube with Tapered End and
Regular End (Upper)
2 Side Tubes
Net
Target
Tube with Tapered End
and Regular End (Lower)
• Please keep this instruction sheet for future reference, as it contains
important information.
• Adult assembly is required.
• Tool needed for assembly: Phillips Screwdriver (not included).
• Hand pump (not included) and inflation pin (included) required to inflate
the soccer ball.
• Requires three “AAA” (LR03) alkaline batteries (not included)
for operation.
• Please remove all parts from the package and identify them
before assembly.
M5 x 28 mm Screw
BOTH SHOWN ACTUAL SIZE
Note: Tighten and loosen all screws with a Phillips Screwdriver.
Do not over-tighten the screws.
M5 Lock Nut
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.
©2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA L5805a-0920
PARTS
PARTS
PARTS

3
Long End
3
1
Rounded
Side
• Place a tube with tapered end and regular end on a flat surface.
• Fit a tube with tapered ends into the regular end, as shown.
Hint: The tube assembly should form this shape .
• Align the holes in the tubes.
• Fit a lock nut, rounded side out, into the hex hole on the inside of the
tube with tapered end and regular end.
• Insert a screw through the outside of the tube with tapered end and
regular end.
• While holding the lock nut in place, tighten the screw.
• Fit the long end of a side tube onto either tapered end of the assembly.
• Align the holes in the two tubes.
Hint: If the holes in the tubes do not align, remove the side tube and place
it on the other end of the assembly.
• Fit a lock nut, rounded side out, into the hex hole in the inside of
the side tube.
• Insert a screw through the hole on the outside of the side tube.
• While holding the lock nut in place, tighten the screw.
Side Tube
Tapered
End
Long End
• Fit the long end of the other side tube onto the other tapered end of
the assembly.
• Align the holes in the two tubes.
• Fit a lock nut, rounded side out, into the hex hole on the inside of
the side tube.
• Insert a screw through the hole on the outside of the side tube.
• While holding the lock nut in place, tighten the screw.
Tube with Tapered
End and Regular End
Tube with Tapered Ends
Side Tube
Tapered
End
Rounded
Side
1
2
Rounded
Side
ASSEMBLY
ASSEMBLY
ASSEMBLY
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION

4
Long Sleeve
TOP OF NET
BOTTOM OF NET
• Lay the net on a flat surface.
• Note the long sleeve, two side sleeves and two short sleeves on the net.
- Long sleeve is the top of the net.
- Binding is the bottom of the net.
4
• Locate the side sleeves on the sides of the net.
• First, fit the side sleeve onto the side tube.
Note: The short sleeve should not be fitted onto the tube.
Short Sleeve
• Next, fit the long sleeve and other side sleeve on to the side tube.
Note: The short sleeve should not be fitted onto the tube.
• Slide the sleeves and the net evenly around the frame, as shown.
5
Side Sleeves
6
7
ASSEMBLY
ASSEMBLY
ASSEMBLY
Binding
Side Sleeve Side Sleeve
Short Sleeve
Short Sleeve

5
• Fit the short end of the tube into the frame assembly.
• Fit the long end of the remaining tube through the short sleeve and weave
the tube through the openings on the edge of the net.
• Fit the short end of the tube into the frame assembly.
• Fit the long end of either remaining tube through the short sleeve.
• Now, weave the tube through the openings on the edge of the net
(about half way).
Short End of Tube
Short End of Tube
Long End of Tube
Short Sleeve
Short
End of
Tube
Short End of Tube
Long End of Tube
Short Sleeve
8
9
10
11
ASSEMBLY
ASSEMBLY
ASSEMBLY