Fisher FIELDVUE DLC3010 User manual

www.Fisher.com
Fisher™FIELDVUE™DLC3010 Digital Level
Controller
Contents
Installation 2.....................
Mounting 8.......................
Electrical Connections 13...........
Initial Setup 18....................
Calibration 23.....................
Schematics 28....................
Specifications 29..................
Note
This guide describes how to install, setup, and calibrate the DLC3010 using a 475 Field
Communicator. For all other information on this product, including reference materials,
manual setup information, maintenance procedures, and replacement part details refer
to the DLC3010 Instruction Manual (D102748X012). If a copy of this document is required,
contact your Emerson Process Management sales office or visit our website at www.Fisher .com.
For information on using the Field Communicator, see the Product Manual for the Field
Communicator, available from Emerson Performance Technologies.
Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
This quick start guide applies to:
Device Type DLC3010
Device Revision 1
Hardware Revision 1
Firmware Revision 8
DD Revision 3
W7977-1
Scan or click
to access sales
office information

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
2
Installation
WARNING
To avoid personal injury, always wear protective gloves, clothing, and eyewear when performing any installation
operations.
Personal injury or property damage due to sudden release of pressure, contact with hazardous fluid, fire, or explosion can
be caused by puncturing, heating, or repairing a displacer that is retaining process pressure or fluid. This danger may not
be readily apparent when disassembling the sensor or removing the displacer. Before disassembling the sensor or
removing the displacer, observe the appropriate warnings provided in the sensor instruction manual.
Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.
This section contains digital level controller installation information, including an installation flowchart (figure 1),
mounting and electrical installation information, and a discussion of failure mode jumpers.
Do not install, operate, or maintain a DLC3010 digital level controller without being fully trained and qualified in valve,
actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is
important to carefully read, understand, and follow all of the contents of this manual, including all safety cautions and
warnings. If you have any questions regarding these instructions contact your Emerson Process Management sales
office before proceeding.

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
3
Figure 1. Installation Flowchart
START HERE
Factory mounted
on 249 sensor?
Use Setup Wizard
to enter sensor
data and
calibration
condition
Check Alarm
Jumper Position
Mount and Wire
Digital level
Controller
Power
Digital level
Controller
No
Yes
Install heat
insulator
assembly
High
temperature
application?
Yes
No
Set Level Offset
to Zero
Calibrate
sensor
Wire
Digital Level
Controller
Power
Digital Level
Controller
Enter Tag, Messages,
Date, and check or set
target application data
Density
Measurement?
Set
Range Values
Using
Temperature
Correction?
Set
Temperature
Units
Setup specific
gravity tables
Set
Specific Gravity
Yes
No
Yes
No
Using RTD?
Yes Setup and
Calibrate RTD
Enter Process
Temperature
No
1
1
DONE
Disable Writes
NOTE:
1 IF USING RTD FOR TEMPERATURE CORRECTION,
ALSO WIRE RTD TO DIGITAL LEVEL CONTROLLER
2 DISABLING WRITES IS EFFECTIVE ONLY IF THE DLC3010 REMAINS
POWERED‐UP
2

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
4
Configuration: On the Bench or in the Loop
Configure the digital level controller before or after installation. It may be useful to configure the instrument on the
bench before installation to ensure proper operation, and to familiarize yourself with its functionality.
Protecting the Coupling and Flexures
CAUTION
Damage to flexures and other parts can cause measurement errors. Observe the following steps before moving the sensor
and controller.
Lever Lock
The lever lock is built in to the coupling access handle. When the handle is open, it positions the lever in the neutral
travel position for coupling. In some cases, this function is used to protect the lever assembly from violent motion
during shipment.
A DLC3010 controller will have one of the following mechanical configurations when received:
1. A fully assembled and coupled caged‐displacer system is shipped with the displacer or driver rod blocked within the
operating range by mechanical means. In this case, the access handle (figure 2) will be in the unlocked position.
Remove the displacer‐blocking hardware before calibration. (See the appropriate sensor instruction manual). The
coupling should be intact.
Figure 2. Sensor Connection Compartment (Adapter Ring Removed for Clarity)
PRESS HERE TO
MOVE ACCESS
HANDLE
SLIDE ACCESS HANDLE
TOWARD FRONT OF UNIT
TO EXPOSE ACCESS HOLE
ACCESS HOLE
MOUNTING
STUDS
SHAFT CLAMP
SET SCREW

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
5
CAUTION
When shipping an instrument mounted on a sensor, if the lever assembly is coupled to the linkage, and the linkage is
constrained by the displacer blocks, use of the lever lock may result in damage to bellows joints or flexure.
2. If the displacer cannot be blocked because of cage configuration or other concerns, the transmitter is uncoupled
from the torque tube by loosening the coupling nut, and the access handle will be in the locked position. Before
placing such a configuration into service, perform the Coupling procedure.
3. For a cageless system where the displacer is not connected to the torque tube during shipping, the torque tube
itself stabilizes the coupled lever position by resting against a physical stop in the sensor. The access handle will be
in the unlocked position. Mount the sensor and hang the displacer. The coupling should be intact.
4. If the controller was shipped alone, the access handle will be in the locked position. All of the Mounting, Coupling
and Calibration procedures must be performed.
The access handle includes a retaining set screw, as shown in figures 2 and 6. The screw is driven in to contact the
spring plate in the handle assembly before shipping. It secures the handle in the desired position during shipping and
operation. To set the access handle in the open or closed position, this set screw must be backed out so that its top is
flush with the handle surface.
Hazardous Area Approvals and Special Instructions for “Safe Use” and
Installations in Hazardous Locations
Certain nameplates may carry more than one approval, and each approval may have unique installation/wiring
requirements and/or conditions of “safe use”. These special instructions for “safe use” are in addition to, and may
override, the standard installation procedures. Special instructions are listed by approval type.
Note
This information supplements the nameplate markings affixed to the product.
Always refer to the nameplate itself to identify the appropriate certification. Contact your Emerson Process Management sales
office for approval/certification information not listed here.
WARNING
Failure to follow these conditions of safe use could result in personal injury or property damage from fire or explosion, or
area re‐classification.
CSA
Special Conditions of Safe Use
Intrinsically Safe, Explosion‐proof, Division 2, Dust Ignition‐proof
Ambient temperature rating: -40_C ≤Ta ≤+80_C; -40_C ≤Ta ≤+78_C; -40_C ≤Ta ≤+70_C
Refer to table 1 for approval information.

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
6
Table 1. Hazardous Area Classifications—CSA (Canada)
Certification Body Certification Obtained Entity Rating Temperature Code
CSA
Ex ia Intrinsically Safe
Class I, Division 1, 2 Groups A, B, C, D
Class II, Division 1, 2 Groups E, F, G
Class III
T6 per drawing 28B5744 (see figure 13)
Vmax = 30 VDC
Imax = 226 mA
Ci = 5.5 nF
Li = 0.4 mH
T6 (Tamb ≤80°C)
Explosion-proof
Class I, Division 1 GP B,C,D T5/T6 - - - T5 (Tamb ≤80°C)
T6 (Tamb ≤78°C)
Class I Division 2 GP A,B,C,D T5/T6 - - - T5 (Tamb ≤80°C)
T6 (Tamb ≤70°C)
Class II Division 1,2 GP E,F,G T5/T6
Class III T5/T6 - - - T5 (Tamb ≤80°C)
T6 (Tamb ≤78°C)
FM
Special Conditions of Safe Use
Intrinsically Safe, Explosion‐proof, Non‐incendive, Dust Ignition‐proof
1. This apparatus enclosure contains aluminum and is considered to constitute a potential risk of ignition by impact or
friction. Care must be taken into account during installation and use to prevent impact or friction.
Refer to table 2 for approval information.
Table 2. Hazardous Area Classifications—FM (United States)
Certification Body Certification Obtained Entity Rating Temperature Code
FM
IS Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,
E,F,G T5 per drawing 28B5745 (see figure 14)
Vmax = 30 VDC
Imax = 226 mA
Ci = 5.5 nF
Li = 0.4 mH
Pi = 1.4 W
T5 (Tamb ≤80°C)
XP Explosion‐proof
Class I Division 1 GP B,C,D T5
NI Non‐incendive
Class I Division 2 GP A,B,C,D T5
DIP Dust Ignition‐proof
Class II Division 1 GP E,F,G T5
S Suitable for Use
Class II, III Division 2 GP F,G
- - - T5 (Tamb ≤80°C)
ATEX
Special Conditions for Safe Use
Intrinsically Safe
The apparatus DLC3010 is an intrinsically safe apparatus; it can be mounted in a hazardous area.
The apparatus can only be connected to an intrinsically safe certified equipment and this combination must be
compatible as regards the intrinsically safe rules.
Operating ambient temperature: -40_C to + 80_C
Flameproof
Operating ambient temperature: -40_C to + 80_C
The apparatus must be fitted with a certified Ex d IIC cable entry.

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
7
Type n
This equipment shall be used with a cable entry ensuring an IP66 minimum and being in compliance with the relevant
European standards.
Operating ambient temperature: -40_C to + 80_C
Refer to table 3 for additional approval information.
Table 3. Hazardous Area Classifications—ATEX
Certificate Certification Obtained Entity Rating Temperature Code
ATEX
Intrinsically Safe
II 1 G D
Gas
Ex ia IIC T5 Ga
Dust
Ex ia IIIC T83°C Da IP66
Ui = 30 VDC
Ii = 226 mA
Pi = 1.4 W
Ci = 5.5 nF
Li = 0.4 mH
T5 (Tamb ≤80°C)
Flameproof
II 2 G D
Gas
Ex d IIC T5 Gb
Dust
Ex tb IIIC T83°C Db IP66
- - - T5 (Tamb ≤80°C)
Type n
II 3 G D
Gas
Ex nA IIC T5 Gc
Dust
Ex t IIIC T83°C Dc IP66
- - - T5 (Tamb ≤80°C)
IECEx
Intrinsically Safe
The apparatus can only be connected to an intrinsically safe certified equipment and this combination must be
compatible as regards the intrinsically safe rules.
Operating ambient temperature: -40_C to + 80_C
Flameproof, Type n
No special conditions for safe use.
Refer to table 4 for approval information.
Table 4. Hazardous Area Classifications—IECEx
Certificate Certification Obtained Entity Rating Temperature Code
IECEx
Intrinsically Safe
Gas
Ex ia IIC T5 Ga
Dust
Ex ia IIIC T83°C Da IP66
Ui = 30 VDC
Ii = 226 mA
Pi = 1.4 W
Ci = 5.5 nF
Li = 0.4 mH
T5 (Tamb ≤80°C)
Flameproof
Gas
Ex d IIC T5 Gb
Dust
Ex t IIIC T83°C Db IP66
- - - T5 (Tamb ≤ 80°C)
Type n
Gas
Ex nA IIC T5 Gc
Dust
Ex t IIIC T83°C Dc IP66
- - - T5 (Tamb ≤80°C)

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
8
Mounting
Mounting the 249 Sensor
The 249 sensor is mounted using one of two methods, depending on the specific type of sensor. If the sensor has a
caged displacer, it typically mounts on the side of the vessel as shown in figure 3. If the sensor has a cageless displacer,
the sensor mounts on the side or top of the vessel as shown in figure 4.
Figure 3. Typical Caged Sensor Mounting
A3789‐1
LIQUID LEVEL
Figure 4. Typical Cageless Sensor Mounting
A3788‐1
The DLC3010 digital level controller is typically shipped attached to the sensor. If ordered separately, it may be
convenient to mount the digital level controller to the sensor and perform the initial setup and calibration before
installing the sensor on the vessel.
Note
Caged sensors have a rod and block installed on each end of the displacer to protect the displacer in shipping. Remove these parts
before installing the sensor to allow the displacer to function properly.

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
9
DLC3010 Orientation
Mount the digital level controller with the torque tube shaft clamp access hole (see figure 2) pointing downward to
allow accumulated moisture drainage.
Note
If alternate drainage is provided by the user, and a small performance loss is acceptable, the instrument can be mounted in 90
degree rotational increments around the pilot shaft axis. The LCD meter may be rotated in 90 degree increments to accommodate
this.
The digital level controller and torque tube arm are attached to the sensor either to the left or right of the displacer, as
shown in figure 5. This can be changed in the field on a 249 sensor (refer to the appropriate sensor instruction
manual). Changing the mounting also changes the effective action, because the torque tube rotation for increasing
level, (looking at the protruding shaft), is clockwise when the unit is mounted to the right of the displacer and counter‐
clockwise when the unit is mounted to the left of the displacer.
All caged 249 sensors have a rotatable head. That is, the digital level controller can be positioned at any of eight
alternate positions around the cage as indicated by the position numbers 1 through 8 in figure 5. To rotate the head,
remove the head flange bolts and nuts and position the head as desired.
Mounting the Digital Level Controller on a 249 Sensor
Refer to figure 2 unless otherwise indicated.
1. If the set‐screw in the access handle is driven against the spring plate, use a 2 mm hex key to back it out until the
head is flush with the outer surface of the handle (see figure 6) . Slide the access handle to the locked position to
expose the access hole. Press on the back of the handle as shown in figure 2 then slide the handle toward the front
of the unit. Be sure the locking handle drops into the detent.
2. Using a 10 mm deep well socket inserted through the access hole, loosen the shaft clamp (figure 2). This clamp will
be re‐tightened in the Coupling portion of the Initial Setup section.
3. Remove the hex nuts from the mounting studs. Do not remove the adapter ring.
CAUTION
Measurement errors can occur if the torque tube assembly is bent or misaligned during installation.

Quick Start Guide
D103214X012
DLC3010 Digital Level Controller
February 2016
10
Figure 5. Typical Mounting Positions for FIELDVUE DLC3010 Digital Level Controller on Fisher 249 Sensor
8
24
6
3
7
1
5
SENSOR
CAGED
CAGELESS
RIGHT‐OF‐DISPLACER
LEFT‐OF‐DISPLACER
11
1 NOT AVAILABLE FOR SIZE NPS 2 CL300 AND CL600 249C SENSOR.
19B2787 Rev. D
19B6600 Rev. C
B1407‐2
8
2
4
6
1
3
7
5
Figure 6. Close‐up of Set‐Screw
SET‐SCREW
4. Position the digital level controller so the access hole is on the bottom of the instrument.
5. Carefully slide the mounting studs into the sensor mounting holes until the digital level controller is snug against
the sensor.
6. Reinstall the hex nuts on the mounting studs and tighten the hex nuts to 10 NSm (88.5 lbfSin).