flamco Falx F1219 User manual

Flamco Falx
Landscape
Portrait

2 1
N
S
E
Y
W
SE
A.
ZE
A2.A1. A3.
X
[mm]
W
[mm]
Z*
[Position]
Y
[mm]
F1219 F1411 F2035 F1219 F1411 F2035
794 - 801 981 - 988 1601 - 1608 A 647 838 1463
802 - 808 989 - 996 1609 - 1615 B 655 846 1471
809 - 816 997 - 1004 1616 - 1623 C 663 854 1479
817 - 824 1005 - 1012 1624 - 1631 D 671 862 1487
825 - 832 1013 - 1020 1632 - 1638 E 679 870 1495
833 - 839 1021 - 1028 1639 - 1646 F 687 878 1503
840 - 847 1029 - 1036 1647 - 1654 G 695 886 1511
848 - 855 1037 - 1044 1655 - 1662 H 703 894 1519
856 - 863 1045 - 1052 1663 - 1670 I 711 902 1527
864 - 871 1053 - 1060 1671 - 1678 J 719 910 1535
A5.
A4.
X
X
W
Landscape
Portrait

N
S
E
W
SE
B3.
B.
B1. B2.
Max. 300 mm
Max. Ø15 mm
kg
= www.flamcofalx.com
kg
<=
www.amcofalx.com
kg
< =
kg =

C3.
C4.
C1. C2.
max. 50 mm
C5. C6.
min. 20 mm
CL.
CP.
§ 2.2

ENG Installationandoperatinginstruction
1. General
Flamco Falx is an universal PV panel mounting system for at roofs.
Install the product in accordance with the installation instructions provided by Flamco. Read these
instructions carefully before commencing installation. After installation, hand over all documenta-
tion, including the ballast calculation, to the end user of the installation.
2. Instructions
Please observe the Instructions below. If these Instructions are not followed, the warranty may be
invalidated. In this case, always contact your supplier.
2.1 General
• The installation must be carried out by qualied personnel using the original Flamco Falx parts.
•Do not use any non-specied installation materials.
•Use the individual parts as instructed only.
•The range of the ambient temperature is - 30 °C to +90 °C.
•Observe local legislation and guidelines.
•Observe the static snow load and wind load requirements.
2.2 Installation
•The installer is responsible for the correct installation.
•Check in advance that the structure can bear the weight of the system. Mount the system on
an approved or suitable structure and base.
•The product can be installed within a temperature range of 0 °C to +40 °C.
•Install the system only on a at, clean and smooth surface with a maximum 5° pitch.
* Always check that the suggested rail position suits the PV panel before installing the whole
eld! Due to external factors (such as roof surface irregularities), the rail position may need to
be located one increment adjacent to the suggested position (g. A5).
•For landscape installation the panel must be secured at each of the four corners with a clip in
the clip mounting points within the mounting blocks. The intermediate clips should at least be
tted in alternate mounting points (g. CL).
For portrait installation the panel must be secured with clips in all clip mounting points of the
mounting blocks (g. CP).
•The ballast calculator is an application. The ballast must meet the prescribed weights
(see www.amcofalx.com).
•Maximum dimensions of a single coupled installation: 100 x 100 metres.
•Always follow the installation instructions and user manual of the panel manufacturer when
installing the panels.
2.3 Maintenance
The system must be inspected annually to check compliance with the installation instructions.
Such inspection should verify that:
•No ballast has been removed or displaced.
•All components and connections are in good order and the positioning of the equipment is
same as the original design.
It is recommended that the installation be inspected following a storm or earthquake.
3. Disposal
Observe local regulations for disposing of the various components.
ENG

MC01059/V5.0/04-2015
Copyright Flamco B.V., Bunschoten, die Niederlande.
Nichts aus dieser Ausgabe darf ohne ausdrückliche Freigabe
und mit Angabe der Quelle vervielfältigt oder auf irgendeine
andere Weise veröffentlicht werden. Die erwähnten Angaben
gelten nur für die Anwendung von Flamco Produkten. Für
eine unsachgemäße Nutzung, Anwendung oder Interpretation
der technischen Daten übernimmt Flamco B.V. keine Haftung.
Technische Änderungen vorbehalten.
Copyright Flamco B.V., Bunschoten, the Netherlands.
No part of this publication may be reproduced or published in
any way without explicit permission and mention of the source.
The data listed are solely applicable to Flamco products.
Flamco B.V. shall accept no liability whatsoever for incorrect use,
application or interpretation of the technical information.
Flamco B.V. reserves the right to make technical alterations.