VISIONARY DESIGNS MOD-1139 Manual

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1139 - General Layout
Attach Plex shelves to
Counter Top using
Stand-off Barrels and Caps.
Place Shelf atop Supports inside assembled
Pedestal.
Set Counter atop assembled Pedestal.
8
10
12
14
16
18
9
11
13
15
17
19
20
10
12 18
8
16
14
Insert
Insert Insert
Insert
Insert
Doors
Item Number
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
34.25"w Horizontal Extrusion
42"h Vertical Extrusion
5.866"w Horizontal Extrusion
42"h Vertical Extrusion
Curved Horizontal Extrusion
42"h Vertical Extrusion
21.0358"w Horizontal Extrusion
42”h Vertical Extrusion
Curved Horizontal Extrusion
42”h Vertical Extrusion
5.856”w Horizontal Extrusion
42”h Vertical Extrusion
38.4173"h Vertical Extrusion
Qty
2
1
2
1
2
1
2
1
2
1
2
1
1
Setup:
1) Connect horizontal extrusions [8, 10, 12, 14, 16 and 18]
between vertical extrusions [9, 11, 13, 15, 17, and 19].
2) Connect vertical extrusion [20] to horizontal extrusion 8 as shown.
3) Place inserts and doors where indicated.
4) Connect upper horizontal extrusions [8, 10, 12, 14, 16 and 18]
between vertical extrusions [9, 11, 13, 15, 17, and 19].
5) Attach Velcroed counter supports to inside of pedestal.
6) Set shelf into assembled pedestal and place counter atop.
7) Attach plex shelves to counter top using stand-off barrels and caps.
Slide Door into
Place atop Hinge
as shown.

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews