Flash DJ Series User manual

LED MOVING HEAD
19x15W BIG EYE
SERIES: DJ
User Manual
Art No F7100768
(ver.05.23)
EAN 5905358808481
21/35/78/97/112 CH

CONTENTS
INTRODUCTION 3
SAFETY INFORMATION 3
PRODUCT INFORMATION 4
INSTALLATION 4
CONNECTION 6
DMX CHART 8
PHOTOMETRICS 10
WARNING! The Led Moving Head (LMH) has a powerful pan and lt mo-
tor. The torque reacon when the head is panned suddenly can cause the
base to move if the xture is standing unsecured on a surface. Do not apply
power to the LMH unless the baase is securely fastened to a surface or to
rigging hardware.
WARNING! Use 2 clamps to rig the xture. Do not hang the xture from
only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners
are locked only when turned a full 900 clockwise.
WARNING! When clamping the xture to a truss or other structure at
any other angle than with the yoke hanging vercally downwards, use two
clamps of half-coupler type. Do not use any type of clamp that does not
completely encircle the structure when fastened.
WARNING! Posion or shade the head so that the front lens will not be
exposed to sunlight or any other strong light source from any angle - even
for a few seconds. See Figure 1. The LMH lens can focused the sun’s rays,
creang a potenal re hazard and causing damage.
IMPORTANT! Do not point strong light output from other xtures at the
LMH, as intense illuminaon can damaged the display.
Figure 1.
2

INTRODUCTION
SAFETY INFORMATION
THANK YOU FOR PURCHASING 19x15W BIG EYE. FOR SAFETY
REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CA-
REFULLY READ THE INSTRUCTIONS.
Please keep this User Manual
for future consultaon. If you sell
the xture to another user, be sure
that they also receive this instruc-
on booklet.
Unpack and check carefully the-
re is no transportaon damage be-
fore using the xture.
Before operang, ensure that
the voltage and frequency of po-
wer supply match the power
requirements of the xture.
It’s important to ground the
yellow/green conductor to earth
in order to avoid electric shock.
Disconnect main power before
servicing and maintenance.
Use safety chain when xes this
xture. Don’t handle the xture by
taking its head only, but always by
taking its base.
Maximum ambient temperature
is: 40°C Don’t operate it where the
temperature is higher than this.
In the event of serious ope-
rating problem, stop using the
fixture immediately. Never try
to repair the fixture by your-
self.
Repairs carried out by unskil-
led people can lead to damage
or malfunction. Please contact
the nearest authorized techni-
cal assistance center. Always
use the same type spare parts.
Do not connect the device
to any dimmer pack.
Do not touch any wire during
operation and there might be a
hazard of electric shock.
To prevent or reduce the risk
of electrical shock or fire, do
not expose the fixture to rain
or moisture.
The housing must be repla-
ced if they are visibly damaged.
Do not look directly at the li-
ght spot while the fixture is on.
3
In the latest version of this Head, the colors in the macro channel have been
improved, making them more natural and consistent with the paern. The co-
lors on the dimmers, power and parameters remain the same as in the previous
version (F7100547).

PRODUCT INFORMATION
INSTALATION
Light Source:
19 pcs x 15W 4in1 LEDs
Power consumpon: 300W
Power supply voltage:
110-245V, 50/60Hz AC
PAN range: 540°
TILT range: 270°
Beam angle (min/max): 4°-60°
Color: RGBW
Zoom: Yes
LED outline stripe eect
Operang modes: DMX 512,
Auto-running, Master/Salve,
Sound acve
DMX channel mode
21/35/78/78/97/112
IP Rang: IP65
Housing made: ABS
Integrated fastening hooks
Cooling: Acve
AC IN/OUT: PowerCon
3-Pin XLR DMX Input/Output
Net Weight: 14.4 kg
Weight with packaging:
59 kg (2x MH+Case)
Dimensions:
H(48)xW(40)xD(26) cm
Dim. (case):
H(59)xW(74)xD(46) cm
The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is rmly xed to avoid vibraon and slipping while
operang. Always ensure that the structure to which you are aaching
the unit is secure and is able to support a weight of 10 mes of the
unit’s weight. Also always use a safety cable that can hold 12 mes of
the weight of the unit when installing the xture. The equipment must
be xed by professionals. And it must be xed at a place where is out of
the touch of people and has no one pass by or under it.
The following item
are included inside the case:
4
❶ - Moving Head (2pcs)
❷ - powerCON cable (2pcs)
❸ - Omega clamp (4pcs)
❹ - User manual (1pc)
❺ - Transport Case
F7100767 [EAN 5905358808474]:
2x Moving Heads 19x15W Big Eye SET ver.05.23 + Case (SET)
AVAILABLE VERSIONS:

The following item
are included inside the box:
5
❶ - Moving Head (1pc)
❷ - powerCON cable (1pc)
❸ - Omega clamp (2pcs)
❹ - User manual (1pc)
❶
❶
❷
❷
❸
❸
❹
❹
❺
User
Manual
User
Manual
F7100768 [EAN 5905358808481]:
1x Moving Head 19x15W Big Eye SET ver.05.23 (carton package)

6
CONNECTION
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): powerCON socket
The connecon is performed using cable with
XLR-female -> XLR-Male plugs.
1
3
22
SHIELD
SIGNAL (+)
SIGNAL (-)
3
1
FEMALE
XLR
MALE
XLR
1
SHIELD
SIGNAL (+)
SIGNAL (-)
FEMALE
XLR
MALE
XLR
2
3
4
5
1
2
3
45
CAUTION! At the last xture, the
DMX signal has to be terminated
with a terminator. Solder a 120Ω
resistor between signal (-) and si-
gnal (+) into a XLR plug and plug
it in the DMX output of the last
xture.
3-PIN XLR
5-PIN XLR
Diagram of connecon of devices by DMX cable.
IMPORTANT! The maximum number of devices connected
in series via power cable is 6 pcs.
DMX
Controller DMX 512 DMX 512 120
Ω

Using lamp, the change rate of power voltage should be within ±10%,
if the voltage is too high, it will shorten the light’s life; if it’s not enough,
the lamp will be dark. Please restart it aer turning o light for 20 mi-
nutes unl full-cooling. Frequent switching will reduce the life span of
lamps and bulbs; intermient using will improve the life of bulbs and
lamps.
Input Voltage Frequency Total Power
100-245[V] AC 50/60[Hz] 300[W]
Voltage Specycaon.
7
The connecon is performed using power cable with powerCON
TRUE1 connector (included). The device must be operated by qualied
personnel.
CAUTION! In the case of cable damage do not aempt to repair. Repla-
cement or repair can be made only on the manufacturer or by a person
with appropriate permissions

8
DMX CHART
21 CH 35 CH
CHANNEL MODE
1Red
2Red ne
3 Green
4Green ne
5 Blue
6Blue ne
7 White
8White ne
9 Linear CTO
10 Macro colour
11 Strobe
12 Dimmer
13 Dimmer Fine
14 Pan
15 Pan Fine
16 Tilt
17 Tilt Fine
18 Funcon
19 Reset
20 Zoom
21 Zoom Rotaon
CHANNEL MODE
1Red
2Red ne
3 Green
4Green ne
5 Blue
6Blue ne
7 White
8White ne
9 Linear CTO
10 Macro colour
11 Strobe
12 Dimmer
13 Dimmer Fine
14 Pan
15 Pan Fine
16 Tilt
17 Tilt Fine
18 Funcon
19 Reset
20 Zoom
21 Zoom Rotaon
22 Shape Selecon
23 Shape Speed
24 Shape Fade
25 Shape R
26 Shape G
27 Shape B
28 Shape W
29 Shape Dimmer
30 Background Dimmer
31 Shape Transion
32 Shape Oset
33 Foreground Strobe
34 Background Strobe
35 Background Select

9
CHANNEL MODE
1 Red LED 1
2 Green LED 1
3 Blue LED 1
… Red LED …
… Green LED …
… Blue LED …
55 Red LED 19
56 Green LED 19
57 Blue LED 19
CHANNEL MODE
1 Red LED 1
2 Green LED 1
3 Blue LED 1
4 White LED 1
… Red LED …
… Green LED …
… Blue LED …
… White LED …
73 Red LED 19
74 Green LED 19
75 Blue LED 19
76 White LED 19
RGB RGBW

10
PHOTOMETRICS
Distance 1m:
26280,24 lx
6480 K
Ra 75
Measurements under laboratory
condions were made on
a spectrometer GL SPECTIS 1.0
R G B W
RGBW

11

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL