Flashforge Creator Pro 2 User manual

本手册仅适用于金刚狼2 3D打印机
This guide is only applicable to Creator Pro 2 3D printer
󲃾󵄲󱕂󱎻󲐚󱑪
󵋤󱌭󳐏
Quick Start Guide
EN/CN-A01
1.
2.
高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套
或缠绕物。
󲷻󲈢󰾞󵦌
前往闪铸科技官方网站 www.sz3dp.com ，可以在[ 技术支持 ] 页面下载
用户使用手册、切片软件等资料，或查看相关操作视频。
󴹗󲚬󰼞󵂐
Hot! Avoid touching the heating nozzle and heating build plate
in operation.
Moving parts in printer may cause injury. Do not wear gloves or
other sources of entanglement in operation.
1.
2.
WARNING
Please refer to FlashForge official website www.flashforge.com to
download the newest User's Guide, Software and Instruction
Videos. (Support-Support Center-Select a Product)
DOWNLOAD
󰽀󲚚

Unboxing
The Creator Pro 2 was carefully packaged at FlashForge manufacturing facility. Please
follow the unpacking steps laid out below.
CAUTION 1. Remove the package and take out accessories carefully. Do not
use force.
2. Do not tear the yellow high temperature resistant adhesive tape
around the nozzle, it has thermal insulation and high temperature
resistance characteristics.
1. 2.
3.
Open box and remove top foam piece. Firmly grasp the two side handles of
FlashForge Creator Pro 2. Lift it out of the
carton and place it on a stable surface.
Remove the packing bag and then
remove the tape and plastic wrap for
protecting the front door.
4. The accessories shall be displayed. Let
us remove the inner package and take
the accessories out.
1

2
6.
5. Take out the foam with accessories.
Shear two ties on the both sides of
X-axis guide rod.
Take the extruder out and place the
extruder carefully. Avoid the nozzle to
touch the desk, which prevent the nozzle
damage from scratch.
7. Open the door, remove top cover of the
printer and take filament out of the lid.
8. Hold both sides of the printing platform,
and slowly lift the platform from the
bottom to facilitate the removal of the
foam box below.
10. Unpacking is complete. It is recom-
mended that you keep the packaging
materials for later handling or storage.
9. Take out the foam on the bottom of the
platform, and then slowly press the
platform down by hands to the lower
position for easy subsequent installa-
tion.

About Your Creator Pro 2
3
1. Platform
4. LCD panel
7. X-axis guide rod
10. Spring presser
13. Turbofan baffle
16. USB cable input
19. Spool holder
2. Platform support
5. Z-axis guide rod
8. Slot
11. Cooling fan
14. Extruder bracket
17. Filament guidetube buckle
20. Power input
3. Leveling nut
6. Extruder cable bunch
9. Nozzle cooling fan
12. Nozzle
15. SD card slot
18. Spool holder slot
21. Power switch
1
20
21
16
15
19
18
17
23 4 5
8
7
6
13 1412
9
10 11

Accessories

 




Grease 





SD Card 

 


Guide


 

󵋤󱌭󳐏
4




Installation
Lower the platform first and place the
dual extruder on the extruder seat.
Take the M2.5 Allen Wrench from the
tool bag and four M3 bolts from the
accessory kit.
Adjust the extruder location to align the
bolt holes.
Secure the extruder onto the extruder
seat by screwing the M3 bolts in.
1.
2.
3.
4.
Bolt Hole Bolt Hole
5


1.To install a spool holder, level it and insert the end into the corresponding opening.
2.Turn down the spool holder to make the holder bottom cleave to the printer back.
3.Take a roll of filament, then squeeze the spool holder top and mount the filament spool
to the holder.
Please refer to the next page for the
right method of filament mounting.
6


The filament spool must be oriented
correctly (see below).
After filament guide tube fixation
completed, press the left spring presser
of extruder, put filament vertically into
the left filament intake from the other
end of filament guide tube. Lock the filament guide tube with R-shape
buckles.
1.
2.
Filament Guide
Tube Buckle
limited seat


7


Please make sure that the nozzle touches the
anti-oozing plate properly when installed. It is
OK to adjust the distance between the nozzle
and plate manually. It is normal to see scratches
on the surface of the plate after printing for
several times.
 
M3x8


The First Setting
Loading and Unloading
1.
2.
Tap [Tools]-[Filament]
Tap [load], the extruder will start to heat up. After heating to the target temperature,
please manually insert the filament into the filament feeding wheel. When the filament
is ejected from the nozzle, it indicates that loading is completed.
3. Tap [unload], the extruder starts to heat up. After heating to the target temperature,
manually feed out a part of filament from the nozzle, then press down the spring
presser, quickly pull out the filament, and complete unloading.
Print
L Extruder
Load
Unload
Load
Unload
R Extruder
Heating...
L Extruder 75℃ / 220℃
Preheat Tools
Filament
Setting
Level
Status
Home
About
Manual
8

Leveling
1.
2.
Tap [Tools]-[Leveling] to start leveling. The machine will finish homing first.
Clearing the remaining materials on the nozzle first to avoid leveling fails.
After stop movement of extruder and platform, tighten the three nuts below the
platform counterclockwise (To avoid scratch build plate by extruder and it is important
action)
3. Choose one extruder and move it to the first nut by hand. Place a paper under the
extruder and tighten the nut to reduce the distance between extruder and platform.
Gently move the paper and feel the fraction. If move the paper with gent fraction, it is a
suitable distance between extruder and platform. Finished the first place, and repeat
the same actions in the second and third nut.


Filament
Setting
Level
Status
Home
About
Manual
Please wait, device is homing.
Next
Screw the three nuts tnder the platform
counterclockwise until they are tight, then
tap the [Next].
Next
Please adjust the front thumb screw under
Platform when stop.
Next
9

XYZ Axis Calibration
1.
2.
Tap [Tools]-[Setting]-[Z calibration]. Creator Pro 2 uses a compensation layer mecha-
nism. Instead of manually adjusting the installation positions of the left and right
nozzles, a program is used to calculate the height difference between the two nozzles.
The extruder and platform will return to the zero position first, select any extruder to
calibrate. When the temperature of the nozzle and the platform is too high, it will wait
for the nozzle to cool down to 50 ° C to prevent the nozzle from scalding the build tape.
3. Follow the on-screen instructions and insert the leveling card between the nozzle and
the platform, please click Z- or Z + to adjust the appropriate spacing. The adjustment
range is sliding leveling paper. If you feel a little frictional resistance, it indicates that
the distance between the nozzle and the platform is appropriate. When one extruder is
adjusted, it will be switched to another extruder for calibration.

Z Axis Calibration
Print Preheat Tools
Z:0.08
Z-
Z+
OK
Z Calibration
Initializing moving...
Please tap Z-，Z+ to adjust and
put the leveling card between
nozzle and platform to verify a
proper distance.
Filament
Setting
Level
Status
Home
About
Manual
X
Calibration
Y
Calibration
Z
Calibration
Expert
Mode Language FactoryReset
10

1.
2.
Tap [Setting]-[X Calibration], or continue the X-axis calibration after the Z-axis calibra-
tion is completed. After the machine initialization movement is completed, the nozzle
and the platform will be heated. At this time, please ensure that the filament has been
inserted into the extruder.
X-axis calibration: Used to adjust the consistency of the two extruders in the X-axis
direction to prevent misalignment during printing.
After heating, left and right extruders print a line one by one.
3. According to the actual printed lines, click X-, X + to adjust the bias of the extruders and
remove the printed lines; tap the verify button, the left and right extruders will print the
lines again to see if the lines coincide, if they coincide, it means that the X-axis
calibration is completed, if they are inconsistent, continue to adjust, until it coincides.
X Axis Calibration
X Calibration
L: 152/200
R: 164/200
B: 45/50
OK
Verify
X-
X-
R
L
0.00 X+
X+
R
L
X+
R
L
R
L
Please tap X-，X+ to adjust and verify make
sure the lines are aligned.
X
Calibration
Y
Calibration
Z
Calibration
Expert
Mode Language FactoryReset
11

1. Tap [Setting]-[Y Calibration], or continue the Y-axis calibration after the X-axis calibra-
tion is completed. After the machine initialization movement is completed, the nozzle
and the platform will be heated. At this time, please ensure that the filament has been
inserted into the extruder.
Y-axis calibration: Used to adjust the consistency of the two extruders in the Y-axis
direction to prevent misalignment during printing.
Y Axis Calibration
Y Calibration
L: 152/200
R: 164/200
B: 45/50
2. After heating, left and right extruders print a line one by one.
3. According to the actual printed lines, click Y-, Y + to adjust the bias of the extruders and
remove the printed lines; tap the verify button, the left and right extruders will print the
lines again to see if the lines coincide, if they coincide, it means that the Y-axis
calibration is completed, if they are inconsistent, continue to adjust, until it coincides.
Please tap Y-，Y+ to adjust and verify make
sure the lines are aligned.
OK
Verify
Y+
0.00
Y- Y- R
L
Y+ R
L
Y-
L
R
LR
X
Calibration
Y
Calibration
Z
Calibration
Expert
Mode Language FactoryReset
12

First Print
1.
2.
Insert the SD card to the side of machine.
After installing, loading filament and calibrating, it start your first print.
Tap [Print]-[SD card]; choose the test file to print.
Print
Test
sys
flashforge
Preheat 25MB
1519MB
Tools
13

󲀓󳳄
闪铸对Creator Pro 2进行了仔细的包装，请您按照以下的开箱步骤拆除包装箱。
󲷻󲈢󰾞󵦌 1.请小心拆除包装，拿出配件，切勿使用蛮力。
2.请勿撕毁围绕在喷嘴周围的黄色耐高温胶带，它具有保温及耐高温特性。
1. 2.
3.
打开纸箱取出顶部泡沫。 抓住机身两侧的把手，将打印机从纸箱中提
出。
撕除胶带，去除塑料袋。随后撕去固定前门
的胶带。
4. 移除塑料袋后，您可以看到打印机内部的包
装以及配件，我们从上至下逐一来解除包
装，拿出配件。
14

6.
5. 取出装有配件的泡沫盒。剪断左右两边固定X
轴的扎带。
首先将喷头从泡沫中取出，放置在台面上。
喷头的线束较短，在摆放时请注意󱛊󱝇不能
接触台面，避免划伤喷嘴影响打印精度。
7. 从打印机中取出顶罩及耗材包装，取出耗材。 8. 托住打印平台两侧，缓缓将平台从底部抬
起，便于取出下方的泡沫盒。
10. 开箱完成。建议您保留包装材料，以便于以
后的搬运或保存
9. 取出平台底部的泡沫，然后缓慢将打印平台
向下压回较低的位置，便于后续安装。
15

󴳑󱨚󰿞󳿠
16
1.打印平台
4.液晶屏
7.X轴导轨
10.进丝压板
13.导风嘴
16.USB线接口
19.耗材丝盘轴
2.平台支架
5.Z轴导轨
8.顶罩卡槽(四个角)
11.冷却风扇
14.喷头支架
17.导丝管卡扣
20.电源线接口
3.调平螺母
6.喷头线束
9.喷头散热风扇
12.喷头喷嘴
15.SD卡插槽
18.丝盘轴插口
21.电源开关
1
20
21
16
15
19
18
17
23 4 5
8
7
6
13 1412
9
10 11

󴧘󳳄󲼘󱑨
󲍦󱒃󲡍
󳙈󲾣󳿒 󳿒
󴄪󲡣󱴏󰼰󳲴
󵄭󵖛
󲺹󲿤󴈕 󱠍󱁦󴈉
󱋅󱒞󲎆󲍞 󱊘󱊀󴫥󲎆󲍞
󵦉󴁼
󱑴 󰼰󳟫󵂇
󴅭󱟮󲴲󰽬󳈂󳲴
󲍦󱒃󴄪󲡣 󱙁󱔡󲠠󱎴󱑴 󲃾󵄲󱕂󱎻󲐚󱑪
󵘅󱌓
󱑔󱱪󴣍󰼰󱌓
󴴖󱾆󱑴 󴴖󱾆󴣍󲳠
󱾆󱔃󴹇󳿋
󵋤󱌭󳐏
17
󵝅󲾵󰼰󲢒

󱲜󴧘󱛊󱩇
󳥿󱀉󱲜󴧘
首先将平台下降到最低位置，然后如下图所
示，将喷头放置于喷头支架（中塑料）上。
从配件包中取出内六角扳手（M2.5）；从
喷头安装包中取出4颗M3螺丝。
适当调整喷头位置，使喷头与喷头支架的螺
丝孔对齐。
用内六角扳手从喷头支架下方旋入螺丝以固
定喷头。
1.
2.
3.
4.
螺丝孔位 螺丝孔位
18

󱲜󴧘󴄪󲡣󱖟󱴏󰼰󳲴
1.将丝盘轴插入端插入打印机背部的丝盘轴插口中。
2.将丝盘轴向下翻转，最终使得丝盘轴贴住打印机背板。
3.取出耗材，轻按丝盘轴顶端两侧，然后将耗材装入丝盘轴。
丝盘轴插入端
耗材安装方向有要求，详情见下一页
19