Flashforge DREAMER User manual

This guide is only applicable to FLASHFORGE Dreamer 3D printer
The User Guide is in the SD card.
USERGUIDE
2. Hot! Avoid touching the heating nozzle in operation.
3. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
WARNING 1. Do not remove the wrapping around the nozzle.
DREAMER
Quick Start Guide
SZ01-EN-A02

01
Kit Contents
3D Printer Filament Spool x 2 Lid After-sales Service Card
Power Cable USB Cable
Quick Start Guide
Build Tape x 2 Leveling Card
Extruder’s
Accessory Kit
Do Not Touch 请勿触摸
CAUTION
注意 1.Extruder hot during operation.
使用过程中喷头会发热。
2.Heating plate hot during operation. Allow surface to cool before servicing.
使用过程中加热平台会发热，待平台表面冷却后再操作。 顺时针旋转螺母
升高打印 平台。
即减少平 台与喷嘴 之间
的距离。
逆时针旋转螺母
降低打印平台。
即增加平 台与喷嘴 之间
的距离。
调整平 台支架下方 的螺母，直 至纸片在喷 嘴与平台间 的
运动感受到轻微的阻力。
打印平台调节专用
扫描二 维码， 观看 调平指 导视频 ！
Spool Holder x 2
Side Panel x 2 Tool Box
Tool Box Contents:
SD Card / Tweezer / Graver / Scraper / Screw Box* / Wrench / Grease
Allen Wrench / Phillips Screwdriver / Wrench / Unclogging Pin Tool
Extruder’s Accessory Kit Contents:
M3 x 8 Bolt x 2 / M3 x 6 Bolt / Turbofan Baffle
*Screw Box Contents: PTFE tube, Screws, Leveling Knob

Getting to Know Your Dreamer
02
1.Extruder Cable Bunch 2.Filament Guide Tube 3.Y-Axis Guide Rod 4.X-Axis Guide Rod
5.Build Plate 6.Build Platform 7.Bracket 8.LevelingKnob
9.Z-Axis Guide Rod 10.Touch Screen 11.Cooling Fan 12.Spring Presser
13.Turbofan 14.Turbofan Baffle 15.Left Nozzle
18.SD Card Slot 19.USB Input 20.Reset Button
21.Power Switch 22.Power Input
17.Side Panel
22
18 19 20 21
1
3
4
5
6
7
910
17
8
2
11
12
13
14 15 16
15.Right Nozzle

Unpacking
03
1. Open box and remove bag containing the lid,
Quick start guide, After-sales service card,
levelling card, and two build tapes.
2. Take the power cable and two top foam
sheets out.
3. Firmly grasp the two sides handles of
Dreamer. Lift it out from the carton and place
it on a stable surface. Then you will see the
Toolbox and USB cable in the shipping box.
4. Remove the packing bag.(Tip:Save your
packaging for future transportation and
storage.)
5. Take foam out of the dreamer. 6. Open box. Box includes dual extruder, side
panel x 2, extruder's accessory kit. Take the
dual extruder out and place it onto a clean
surface. Notes: Extruder cable bunch is short.
Please do not leave the extruder hanging by
the cable.

04
7. Remove the bubble wrap from extruder and
slide the X-axis rods to the middle of printer
(A extruder seat on the X-axis).
8. Place the dual extruder on the extruder seat,
as shown.
10. Elevate the build plate to its limit. Notes:
Do not let build plate touch the extruder.
11. Remove both filament rolls and foam pieces
from printer.
Note: Take both spool holders out of the foam.
9. Remove the foam from the back of the logo
board.
12. Lower the build plate fully. Congratulations!
You've unpacked your printer. (Tip: Save
packaging for future transportation and
storage)

05
Hardware Assembly
Extruder Assembly
1. Place the dual extruder on the extruder
seat.
2. Take the M2.5 Allen Wrench from the tool
box and two M3 x 8 bolts(longer ones)
from the extruder’s accessory kit.
3. Adjust the extruder location to align the
bolt holes.
4. Secure the extruder onto the extruder
seat by screwing the M3 x 8 bolts in. Bolt Hole Bolt Hole
M3 x 8 bolts
X-Axis Guide Rod
Bolt Hole
Bolt Hole

06
Turbofan Baffle Assembly
1. Use the M2.5 Allen Wrench to remove two turbofan bolts.
2. Take the turbofan baffle from the extruder’s accessory kit.
3. Install the turbofan baffle to the turbofan.
Bolt Removal
Bolt Removal

07
1. Place the turbofan sub-assembly besides the
turbofan seat.
2. Insert the bump on the turbofan seat to the
turbofan sub-assembly.
3. Screw the two bolts in.
4. Take a M3 x 6 bolt from the extruder’s accessory
kit and complete installation according to the
instruction below.
Turbofan Seat
Bolt Mounting
Bolt MountingBolt Mounting
M3X6 Bolt Mounting
Bolt Mounting
Align the bump on the turbofan
seat to the hole in turbofan
sub-assembly.

Leveling Build Platform
How to use the leveling knobs
Raise the build plate to reduce the distance between the nozzle and build plate.
Lower the build plate to increase the distance between the nozzle and build plate.
Rotate knob clockwise
Rotate knob anticlockwise
Print Preheat Tools
HOME
Filament Level Home Manual
Setting Status About
Language TP Adjust FactoryReset
WIFI
Fan On
Pulley
简体中文
English
繁體中文
日本語
Français
Deutsch
Back Fan
Disable
Filament
Check ON
How to change language
08

How to level the build plate
1. Tighten the three leveling knobs under the build platform until you cannot tighten them any more.
2. Tap [Tools], [Leveling] to start leveling.
3. The build plate and the nozzle start moving, once they suspend, you need to adjust the corresponding
knob under the right nozzle.
4. The leveling card should slide between the nozzle and build plate with some friction/resistance. If the
card slides through easily, the nozzle and build plate are too far apart. Rotate the knob clockwise to
decrease the distance between them. If the card cannot slide through, rotate the knob anticlockwise.
5. After leveling the first point, tap [OK] to continue to the next point.
6. After adjusting the three knobs and making a check when the nozzle is at the center of the plate, you
finish the build plate leveling.
Take the proper distance between
the right nozzle and build plate
as the standard.
09