Flex FX0451 User manual
Model:
Modelo:
Modèle:
OPERATOR’S MANUAL
MANUAL DEL OPERADOR
MANUEL DE L’UTILISATEUR
833-FLEX-496
(833-3539-496)
For English
Version
See page 2
◆
Version
française
Voir page 15
◆
Versión en
español
Ver la página 29
www.Registermyflex.com
Contact Us /
Nous contacter /
Contáctenos
1120W 4-PORT SIMULTANEOUS CHARGER
CHARGEUR SIMULTANÉ À 4 PORTS DE 1120 W
CARGADOR SIMULTÁNEO DE 4 PUERTOS DE 1120 W
FX0451
-2-
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols
and the explanations with them deserve your careful attention and understanding. The symbol
warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are
no substitutes for proper accident prevention measures.
WARNING Be sure to read and understand all safety instructions in this Operator’s Manual,
including all safety alert symbols such as "DANGER," "WARNING," and
"CAUTION" before using this tool. Failure to follow all instructions listed below may result in electric
shock, re, and/or serious personal injury.
The denitions below describe the level of severity for each signal word. Please read the manual and
pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, will result in minor or moderate injury.
Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment or
other property damage if they are not followed. Each message is preceded by the word "NOTICE",
as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not followed.
WARNING The operation of any power tools can result in foreign
objects being thrown into your eyes, which can result in
severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when
needed. We recommend a Wide Vision Safety Mask for use over eyeglasses
or standard safety glasses with side shields. Always use eye protection which
is marked to comply with ANSI Z87.1.
-3-
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
–
This manual contains important safety and
operating instructions for battery charger
Model FX0451. Do not substitute any other
charger.
Before using battery charger, read all
instructions and cautionary markings on
(1) battery charger, (2) battery pack, and (3)
product using battery.
CAUTION To reduce risk of injury,
charge only Li-Ion type
rechargeable batteries. Other types of
batteries may burst causing personal injury and
damage.
Charge only FLEX rechargeable batteries
listed in the manual. Other types of batteries
may burst causing personal injury and damage.
Charge battery pack within the required
temperature range. Store charger and
battery pack in locations where temperature
is within the recommended storage
temperature range. This is important to prevent
serious damage to the battery cells.
Do not recharge battery in damp or wet
environment. Do not expose charger to rain
or snow. Water entering battery charger may
result in electric shock or re.
Battery leakage may occur under extreme
usage or temperature conditions. Avoid
contact with skin and eyes. The battery liquid
is caustic and could cause chemical burns to
tissues. If liquid comes in contact with skin, wash
quickly with soap and water. If the liquid contacts
your eyes, ush them with water for a minimum
of 10 minutes and seek medical attention.
Place charger on at nonammable surfaces
and away from ammable materials when
recharging battery pack. Carpeting and
other heat insulating surfaces block proper air
circulation which may cause overheating of the
charger and battery pack. If smoke or melting
of the charger or battery pack is observed,
unplug the charger immediately and do not use
the battery pack or charger. Contact customer
service immediately.
Keep the cord and charger from heat to
prevent damage to housing or internal parts.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
Do not allow gasoline, oils, petroleum-based
products, etc. to come in contact with plastic
parts. These materials contain chemicals that
can damage, weaken, or destroy plastic.
Make sure cord is located so that it will not
be stepped on, tripped over, or otherwise
subjected to damage or stress. Damaged
plug and cord may result in electric shock or
re.
Disconnect the charger by pulling the plug
rather than the cord. Do not operate charger
with damaged cord or plug; have them
replaced immediately. Damaged plug or cord
may result in electric shock or re.
Do not insert battery pack in charger if
battery pack case is cracked. Using damaged
battery pack may result in electric shock or re.
Do not disassemble charger or operate the
charger if it has received a sharp blow, been
dropped or otherwise damaged in anyway.
Incorrect reassembly or damage may result in
electric shock or re.
Before each use, check the battery charger,
cable and plug. If damage is detected, do
not use the battery charger. Never open
the battery charger yourself, take it to a
FLEX Factory Service Center, or qualied
serviceman only using original spare parts.
Incorrect reassembly may result in electric
shock or re.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualied persons in order
to avoid a hazard.
Do not touch the uninsulated portion of
output connector or uninsulated battery
terminal. There is a risk of electric shock.
-4-
Do not use attachment not recommended
or sold by FLEX.Using attachments not
recommended may result in electric shock or
re.
Do not store battery pack in charger. Battery
pack stored in charger over a long period of
time could lead to battery pack damage and re.
Do not operate the charger if it has received
a sharp blow, been dropped, or has
otherwise been damaged in any way. Take it
to a qualied service technician for an electrical
check to determine if the charger is in good
working order.
Unplug charger from outlet before storage,
attempting any maintenance or cleaning.
Such preventive safety measures reduce the
risk of electric shock or re.
Keep the battery charger clean by blowing
compressed air on charger vents and wiping
the charger housing with a damp cloth.
Contamination may result in electric shock or
re.
Replace battery pack if a substantial drop
in operating time per charge is observed.
Battery pack may be nearing the end of its life.
Charging non-rechargeable batteries is
prohibited.
Children should be supervised to ensure that
they do not play with the charger.
Do not use outdoors.
SAVE THESE INSTRUCTIONS.
EXTENSION CORDS
WARNING AN EXTENSION CORD
SHOULD NOT BE USED
UNLESS ABSOLUTELY NECESSARY. Use of
improper extension cord could result in risk of
re and electrical shock. If an extension cord is
used, make sure:
a. The pins on plug of extension cord are the
same number, size, and shape as those of
plug on charger.
b. The extension cord is properly wired and in
good electrical condition.
c. The wire size is large enough for AC ampere
rating of charger as specied below:
Length of Cord (Feet) 50 100 150
Size of Cord (AWG) 16 16 14
d. An extension cord is a temporary solution. Move the charger to a standard receptacle as soon as
the job has been completed.
-5-
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and
learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better
and safer.
Symbol Name Designation/Explanation
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
Wh Watt-hours Battery capacity
Ah Ampere-hours Battery capacity
ø Diameter Size of drill bits, grinding wheels, etc.
n0No load speed Rotational speed, at no load
n Rated speed Maximum attainable speed
…/min Revolutions or reciprocations per
minute (rpm)
Revolutions, strokes, surface speed, orbits,
etc. per minute
O Off position Zero speed, zero torque...
1,2,3,…
Ⅰ,Ⅱ,Ⅲ, Selector settings Speed, torque, or position settings. Higher
number means greater speed
Innitely variable selector with off Speed is increasing from 0 setting
Arrow Action in the direction of arrow
Alternating current (AC) Type or a characteristic of current
Direct current (DC) Type or a characteristic of current
Alternating or direct current
(AC / DC) Type or a characteristic of current
Class II tool Designates Double Insulated Construction
tools.
Protective earth Grounding terminal
Li-ion RBRC seal Designates Li-ion battery recycling
program
Read the instructions Alerts user to read manual
Table of contents
Languages:
Other Flex Batteries Charger manuals
