FLIR FC S Series Assembly instructions

427-0073-11-28 Rev 100 Feb 2013
FC-Series S Camera
Quick Connect Guide
For installations that are using the Concealed Cable Mounting Arm,
refer to the installation manual for instructions:
FLIR FC-Series S Installation Manual (427-0073-11-12)
Caution!
Note
Except as described in this guide, do not disassemble the FC-Series S camera.
Damage to the camera can occur as the result of careless handling or
electrostatic discharge (ESD).
Prior to making any connections, ensure the power is switched off.
Power: Power Over Ethernet (PoE) or 12-40VDC, 24VAC
Power terminal blocks: wire size from 16 AWG to 20 AWG
Analog Video Cable: BNC-terminated RG-59/U solid-center coax cable
Items Included in Kit
3 mm hex
2.4 mm slotted
screwdriver
key
427-0073-11-28 v100 FC-Series S Quick Connect.fm Page 1 Saturday, March 9, 2013 5:07 PM

427-0073-11-28 Rev 100 Feb 2013
Step 1 Remove cover: Using 3 mm hex key, loosen four captive
screws. Removal of sunshield not necessary.
Step 2 Install cables through sealing gland:
Step 3 If using conventional power cable, strip cables as
described below:
Access captive
screws through
slots in sunshield.
Video coax
Gland nut
Not Used
Power
Ethernet
Ground
Re-tighten gland nut
after installation is
completed.
Fill any unused hole
with orange plug.
(0.8±.20 in)
20.0±5 mm
Remove outer jacket
(0.2±.04 in)
6.0±1 mm
Strip ends 3 Places
Min diameter = 6.8 mm (0.27 in)
Max diameter = 9.4 mm (0.37 in)
Power Cable
427-0073-11-28 v100 FC-Series S Quick Connect.fm Page 2 Saturday, March 9, 2013 5:07 PM

427-0073-11-28 Rev 100 Feb 2013
Step 4 Te r m i n a te c a b l e s :
Step 5 Connect a ground wire between the ground stud on the
back of the camera and the nearest earth-grounding point.
Step 6 Test camera: Power on the camera and test video.
Use a web browser to test IP communications
(default IP: 192.168.250.116; login: user/fliradmin)
Step 7 Tighten Cable seal gland nut to ensure a watertight seal.
Step 8 Replace cover: Alternately tighten the four captive
screws in the cover; torque to 1.8 N-m (16.0 in-lbs).
Connection Purpose
13-pinJumper Lensheateron/off
2 RCA Analog video test point
3BNC Analogvideo
4 3-pin Terminal AC/DC Power
5 Ethernet PoE power, communications, IP video stream
6 Accessory inputs Reserved for future use
Ta b l e 1 - 1 : Po w e r C o n n e c t o r
1Chassis
2VAC/DC-
3VAC/DC+
427-0073-11-28 v100 FC-Series S Quick Connect.fm Page 3 Saturday, March 9, 2013 5:07 PM

427-0073-11-28 Rev 100 Feb 2013
FLIR Systems, Inc.
70 Castilian Drive
Goleta, CA 93117
USA
PH: + 1 805.964.9797
PH: + 1 877.773.3547 (Sales)
PH: + 1 888.747.3547 (Support)
FX: + 1 805.685.2711
www.flir.com
Corporate Headquarters
FLIR Systems, Inc.
27700 SW Parkway Ave.
Wilsonville, OR 97070
USA
PH: +1 503.498.3547
FX: +1 503.498.3153
[e-mail]
Ensure the camera is properly grounded. Failure to properly ground the camera
can lead to permanent damage to the camera. Typical to good grounding
practices, the camera chassis ground should be connected to the lowest
resistance path possible. FLIR requires a grounding strap anchored to the
grounding lug and connected to the nearest earth-grounding point.
Before installing the FC-Series S camera you should read and understand the
following documents which provide details regarding mechanical dimensions
and installation safety.
• FLIR FC-Series S Installation Manual (427-0073-11-12)
• FLIR FC-Series S Interface Control Document (427-00XX-XX-19S)
Documents provided on the documentation CD or from the FLIR website
427-0073-11-28 v100 FC-Series S Quick Connect.fm Page 4 Saturday, March 9, 2013 5:07 PM