FLOS F6430009 User manual

REV. 1
DATE 15/11/2021
1
SKYGARDEN RECESSED
Designed by Marcel Wanders, 2009
F6430009
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.

EN
2
SKYGARDEN RECESSED
F6430009
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
REV. 1
DATE 15/11/2021
01. RF6432000
–Electrical assembly
03. RF6430001
–Rcs diffuser assembly

EN
3
RF6432000
ELECTRICAL ASSEMBLY
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
SKYGARDEN RECESSED
F6430009
REV. 1
DATE 15/11/2021

4
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
RF6432000
ELECTRICAL ASSEMBLY
SKYGARDEN RECESSED
F6430009
Unfasten the glass diffuser (A) from the lamp
body.(Fig.1-2)
Remove the lamp bulb (B) and unfasten the two
locking screws (C).(Fig.3)
Fig.1
Fig.3
Fig.2
A
B
C

5
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
RF6432000
ELECTRICAL ASSEMBLY
SKYGARDEN RECESSED
F6430009
Slide out the damaged electrical assembly (D) from
the lamp body.
Fig.4
Fig.5
D
D

6
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
RF6432000
ELECTRICAL ASSEMBLY
SKYGARDEN RECESSED
F6430009
Unfasten the locking screw (E) of the cable clamp
and of electrical assembly cover flap (F).(Fig.5-6)
Lift-up the cover and disconnect the feed connector
(G) from the damaged
electrical assembly.(Fig.8)
Fig.6
Fig.8
E
G
Fig.7
F

7
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
RF6432000
ELECTRICAL ASSEMBLY
SKYGARDEN RECESSED
F6430009
Fig.9
If perhaps you decide to connect replace the
feed connector, please carry-out the following
procedure:
•Strip-off 9 mm of isolation from the wires
(max 2 mm2). Remark! Do not twist the
copper wires.
•Insert a flat thin screw driver inside the cage
clamping connect or openings (1), insert the
wire (2) and then remove the screw driver (3).
Automatically the wires will lock inside the
connector.
In case you need to remove the wires, please
carry-out the procedure in the
opposite way.
Assemble now the new spare-part:
Connect the connector (G) to the new electrical
assembly.(Fig.8 page 6)
Close the flap cover (F) and tighten the screw
(E).(Fig.6-7 page 8)
Insert the electrical assembly (D) into the lamp
body, ensuring to insert the back
part first and then turn until it is completely
inserted.(Fig.4-5 page 5)
Fix the electrical assembly to the lamp body by
fastening the screws (C). Install the lamp-bulb
(B).(Fig.2-3 page 4)
Screw on the diffuser (A) by keeping it
perpendicular to the threaded screw (B).
REMARK!!! Screw on the diffuser without forcing.
Once reaching the end of the
thread loosen slightly to make it easy for a
future removal.(Fig.1 page 4)

8
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
RF6430001
GLASS DIFFUSER ASSEMBLY
SKYGARDEN RECESSED
F6430009

9
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
REV. 1
DATE 15/11/2021
SKYGARDEN RECESSED
F6430009
Install the lamp-bulb then assemble the diffuser (A)
on the body by fastening it onto the appropriate
threaded screw (B).
REMARK!!! Screw on the diffuser without forcing.
Once reaching the end of
the thread loosen slightly to make it easy for a
future removal.
Fig.4
Fig.5
RF6430001
GLASS DIFFUSER ASSEMBLY