Fluke 8808A Configuration guide

Manual Supplement
© 2008-2012 Fluke Corporation. All rights reserved. 

Manual Title: 8808A Getting Started Supplement Issue: 6
Part Number: 2716412 Issue Date: 12/12
Print Date: July 2007 Page Count: 2
Revision/Date:
This supplement contains information necessary to ensure the
accuracy of the above manual.

8808A Getting Started Manual Supplement
2/10 1
Change #1, 44931, 46479, 47892
On page 1, in the Specifications section, under Relative Humidity (non-condensing), replace
Operating with the following:
Operating................................................ <90 % (0 C to 28 C)
<75 % (28 C to 40 C)
<45 % (40 C to 50 C)
On page 5, under DC Current, Shunt Resistance, replace the Burden Voltage with the
following:
Burden voltage <5 mV for 200 A and 2 mA range.
In the Input Characteristics table, change the Burden Voltage for both 200 µA and 2 mA
ranges,
From: <1 mV
To: <5 mV
Change #2
On page 6, under the Warning, replace steps 4 and 5, with the following:
4. Insert the other end of the test lead into the mA terminal. If the fuse is good, the Meter
displays a reading of <10 . If the fuse is blown, the Meter displays  to indicate an overload.
5. Remove the test lead from the mA terminal and insert it into the 10 A terminal. If the fuse is
good, the Meter displays a reading of <2 . If the fuse is blown, the Meter displays  to
indicate an overload.
Change #3, 53744
Under the LIMITED WARRANTY AND LIMITATION OF LIABILITY replace the second
sentence with the following:
The warranty period is three years limited and begins on the date of shipment.
On page 11, replace Table 6 with the following:
Table 6. Accessories
Item Model / Part Number
Premium Test Lead Set TL71
Fuse, .25*1.25, 0.063 A, 250 V, Slow 163030
Fuse, .25*1.25, 0.125 A, 250 V, Slow 166488
F1 - Fuse, 11 A, 1000 V, Fast, 406INX1.5IN, BULK 803293
F2 - Fuse, 440 mA, 1000 V, Fast, 406INX1.375IN, BULK 943121
Rack Mount Kit 8845A & 8846A Single Y8846S
Rack Mount Kit 8845A & 8846A Dual Y8846D
USB to RS-232 Cable Adapter (included) 884x-USB
Precision Electronic Probe Set TL910
2X4 Wire Ohms 1000 V Test Lead TL2X4W-PTII
FlukeView Forms Basic Software (included) FVF-SC5
FlukeView Forms Software Upgrade to enhanced version FVF-UG

Manual Supplement 8808A Getting Started
2 12/12
In the Specifications section on page 2, change the Warranty,
From:
One year
To: Three years limited
Change #4
On page 6, under the Current-Input Fuses section add the following Table:
Current Input Fuse Table
F1 F1 - Fuse, 11 A, 1000 V, Fast blow or equivalent 803293
F2 F2 - Fuse, 440 mA, 1000 V, Fast blow or equivalent 943121
On page 6, under the Warning replace step 3 with:
Press to set the range to 200 .
On page 7, under the Warning replace step 5 with:
5. Remove the defective fuse and replace it with a fuse of an appropriate rating. See the Current Input
Fuse Table.
Change #5, 64137, 64189
On page 4, add the following to the Symbols, table:
Conforms to relevant South Korean EMC Standards.
Conforms to CAN/CSA-C22.2 No. 61010-1, second edition,
including Amendment 1.
On page 2, in the Specification section, add Electromagnetic Environment and replace
Safety and EMC with:
Safety ................................................................ IEC 61010-1, 600 V CAT II / 1000 V CAT I, Pollution Degree 2
Electromagnetic Environment.............. IEC 61326-1, Basic
EMC.................................................................... Applies to use in Korea only. Class A Equipment (Industrial Broadcasting &
Communication Equipment) [1]
[1] This product meets requirements for industrial (Class A)
electromagnetic wave equipment and the seller or user should take
notice of it. This equipment is intended for use in business
environments and is not to be used in homes.