Fluke SimpliFiber Pro User manual

PN 3314825 (English) September 2008
©2008 Fluke Corporation. All rights reserved. Printed in USA.
All product names are trademarks of their respective companies.
SimpliFiber®Pro
Singlemode Optical Power Source
Instruction Sheet
The SimpliFiber®Pro Singlemode Optical Power Source provides
optical power at 1310 nm and 1550 nm. The source is used with an
optical power meter for testing singlemode fiber optic cable.
The source comes with the following:
• 2 AA alkaline batteries
• Instruction Sheet
If something is damaged or missing, contact the place of
purchase immediately.
Safety Information
WWarning: Class 1 Laser*
To avoid possible eye damage caused by hazardous
radiation:
• Never look directly into optical connectors. Some
sources produce invisible radiation that can
permanently damage your eyes.
• Never turn on the source unless a fiber is attached to
the port.
• Do not use magnification to view the optical outputs
without proper filtering.
• Use of controls, adjustments, or procedures not
stated herein might result in hazardous radiation
exposure.

WCaution
To avoid damaging fiber connectors, to avoid data
loss, and to ensure maximum accuracy of test results:
• Use proper cleaning procedures to clean all fiber
connectors before every use. Neglecting this step or
using improper procedures can cause unreliable test
results and may permanently damage the
connectors.
• Cover all connectors with protective caps when not
in use.
• Never connect the source to an active network.
Doing so can disrupt network operations.
• After you turn on the source, let it warm up for 10
minutes before use. Allow additional time if the
source has been stored above or below ambient
temperature.
Features
fft01.eps
A X: On/off key.
B A: Selects auto wavelength mode, which is used with a
SimpliFiber Pro meter. The AUTO LED lights. The source’s
signal includes an identifier that tells the SimpliFiber Pro
meter which wavelength to measure.
Press Zto change the wavelength. The wavelength LEDs
indicate the wavelength.

C M: Switches between continuous wave and 2 kHz modulated
output signals.
• Use continuous wave mode (CW/2 kHz LED on steady) for
making loss or power measurements with a meter other
than a SimpliFiber Pro meter.
• Use the 2 kHz modulated output mode (CW/2 kHz LED
blinking) if locating fibers with a meter other than a
SimpliFiber Pro meter.
Also enables or disables auto power-off. See "Auto Power-
Off".
D I: Selects FindFiber mode, which is used with a SimpliFiber
Pro meter to help you quickly identify link connections at
patch panels. The ID 2 LED lights if the source is in FindFiber
mode.
E The LOW BATTERY LED blinks continuously if the battery is
low. The LED blinks occasionally if auto power-off is disabled.
See "Auto Power-Off".
F Output port with SC adapter.
Battery Installation, Life, and Status
fft02.eps
• The batteries last for about 30 hours of typical use. See the
specifications.
• Replace the batteries if the LOW BATTERY LED blinks
continuously. The LED blinks occasionally if auto power-off is
disabled. See "Auto Power-Off".
AA
IEC LR6
NEDA 15A
Note: Fluke Networks recommends alkaline batteries.

Auto Power-Off
If auto power-off is enabled, the source turns off after 30 minutes
if no keys are pressed.
To disable or enable auto power-off, hold down Mfor 4 seconds.
• If auto power-off is enabled, all LEDs turn on for 3 seconds.
• If auto power-off is disabled, all LEDs blink for 3 seconds and
the LOW BATTERY LED blinks occasionally.
Registration
Registering your product with Fluke Networks gives you access to
valuable information on product updates, troubleshooting tips,
and other support services. To register, fill out the online
registration form on the Fluke Networks website at
www.flukenetworks.com/registration.
Contacting Fluke Networks
www.flukenetworks.com
[email protected]
[phone]
• Australia: 61 (2) 8850-3333 or 61 (3) 9329-0244
• Beijing: 86 (10) 6512-3435
• Brazil: 11 3759 7600
• Canada: 1-800-363-5853
• Europe: [phone]
• Hong Kong: 852 2721-3228
• Japan: 03-3434-0510
• Korea: 82 2 539-6311
• Singapore: 65 6799-5566
• Taiwan: (886) 2-227-83199
• USA: 1-800-283-5853
Visit our website for a complete list of phone numbers.

Accessories
Visit the Fluke Networks website at www.flukenetworks.com for
a complete list of fiber test equipment and accessories.
Specifications
Operating temperature -10ºC to +50ºC
Storage temperature -20ºC to +50ºC
Emitter type FP laser: dual 1310 nm/1550 nm
Central wavelength 1310 nm, 1550 nm
Wavelength accuracy 1310 nm: ±20 nm
1550 nm: ±30 nm
Spectral bandwidth (RMS) 1310 nm: 2 nm (maximum)
1550 nm: 3 nm (maximum)
Minimum output power 1310/1550 nm: ≥ -7 dB (typical)
Power output stability1±0.25 dB over 8 hours
Auto dual-wavelength
switching
Yes. Can be enabled or disabled
by the user.
Optical connector Fixed SC
FindFiber ID generation Yes. Fixed at ID 2.
Output modes CW (continuous wave), 2 kHz
modulated, auto-wavelength
Power requirement 2 AA alkaline batteries
Battery life230 hours (typical)
Automatic power-off 30 minutes (can be disabled by
the user)
Low battery warning Blinking LED
Size 5.6inx3.2inx1.6in
(14.2 cm x 8.1 cm x 4.1 cm)
Weight 9.8 oz (278 g)
1. 23°C ±2°C, after 5 minutes of warm-up time.
2. In auto-wavelength mode. Battery life depends on the condition
and type of batteries used. Fluke Networks recommends alkaline
batteries.

LIMITED WARRANTY AND LIMITATION OF LIABILITY
Fluke Networks mainframe products will be free from defects in
material and workmanship for one year from the date of
purchase. Parts, accessories, product repairs and services are
warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and
Li-Ion batteries, cables or other peripherals are all considered parts
or accessories.
This warranty does not cover damage from accident, neglect,
misuse, alteration, contamination, or abnormal conditions of
operation or handling. Resellers are not authorized to extend any
other warranty on Fluke Networks’ behalf. To obtain service
during the warranty period, contact your nearest Fluke Networks
authorized service center to obtain return authorization
information, then send your defective product to that Service
Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSED OR IMPLIED. FLUKE NETWORKS IS NOT LIABLE
FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
4/04
PListed by the Canadian Standards Association
;Conforms to relevant Australian standards
)Conforms to relevant European Union directives
Laser
safety
Complies with 21CFR.1040.10,11, and EN60825-1,
2:2007 (Class 1, Hazard Level 1)
Fluke Networks
PO Box 777
Everett, WA 98206-0777
USA