Fluke TAP-1000BT-SX User manual

Unpacking
• (1) Quick Installation Guide
• (1) TAP-1000BT-SX Single Port Copper Tap
• (1) AC power cable
• (1) Power supply
Introduction
The TAP-1000BT-SX is a single-port full-duplex device
that provides an easy method to rapidly and effectively
deploy your analysis tools to monitor 1000BASE-T traffic
between your network devices. Typically the tap is
installed on a critical 1000BASE-T link in the network
where monitoring and analysis capabilities are important.
TAP-1000BT-SX features and benefits:
• 1000BASE-T compatible
• Full duplex monitoring
• Power fault tolerant
• Standard RJ45 and SX connectors
TAP-1000BT-SX Specifications
RRAACCKKIINNSSTTAALLLLAATTIIOONNMMEETTHHOODDSS
Prior to installation, you may want to contact your
Fluke Networks representative first to learn more
about using the included thumbscrew mounting
bracket for mounting in either a 1U 3-bay (TAP-RMK-3)
or 4U 14-bay (TAP-RMK-14) Rack Mount Kit.
Figure 1. TAP-1000BT-SX unit shown with included
thumbscrew bracket for standalone mounting
Figure 2. Three TAP-1000BT-SX devices shown mounted in
optional 3-bay (TAP-RMK-3) Rack Mounting Kit
FFUUNNCCTTIIOONNAALLOOPPEERRAATTIIOONN
Refer to Figure 3 below for a diagram showing
the functional operation of the TAP-1000BT-SX.
Figure 3. TAP-1000BT-SX functional diagram
6-panel Z-fold layout:
CUT AT 4.25in from
^^ right edge of this side ^^
FEATURE SPECIFICATION
CHANNEL One-directional
10/100/1000BASE-T Ethernet
CABLE TYPE CAT 5E and multi-mode fiber
PORT CONNECTIVITY
NETWORK A
NETWORK B
TAP A
TAP B
RJ45
RJ45
SX
SX
DISTANCE LIMIT 90m max. length between
network end-points. Tap typically 1m.
POWER REQUIREMENTS External power supply 5V DC, 1A
OPERATING TEMPERATURE 0° to 40°C (32° to 104°F)
STORAGE TEMPERATURE -30° to 65°C (-22° to 149° )
HUMIDITY RH 5% to 95% non-condensing
DIMENSIONS
(H) 28mm x (W) 146mm x (D) 146mm
(H) 1.10" x (W) 5.75" x (D) 5.75"
(includes rack mount bracket)
WEIGHT unit: 340.2g (12oz)
shipping: 907.2g (2lbs)
Quick
Installation
Guide
AC Power
Cables
AC Power
Supplies

6-panel Z-fold layout:
CUT AT 4.25in from
^^ left edge of this side ^^
CCOONNNNEECCTTIINNGGTTHHEETTAAPP--11000000BBTT--SSXX
TTOOAANNEETTWWOORRKK
To connect the TAP-1000BT-SX into a network,
refer to Figure 4 below and follow these steps:
IMPORTANT
Do not exceed the maximum length of 90 meters
between end-points.
Figure 4. TAP-1000BT-SX simple connectivity diagram
1. Connect the Power Supply barrel connector into
the POWER port of the TAP-1000BT-SX and then
plug the Power Supply into the external power
source wall receptacle. The POWER LED to the
right of the RJ connectors illuminates indicating
power is on.
2. Connect one of the network device cables to the
TAP-1000BT-SX RJ45 port NETWORK A connector.
The NET-A LINK LED will illuminate, indicating link
has been established between the NETWORK A
connector and NETWORK A device.
3. Connect the other network device cable to the
TAP-1000BT-SX RJ45 port NETWORK B connector.
The NET-B LINK LED will illuminatel indicating link
has been established between the NETWORK B
connector and NETWORK B device (the Rx-A,
Tx-A, Rx-B, and Tx-B LEDs illuminate as data is
passed back and forth between the NETWORK A
and NETWORK B device).
4. Connect one tap cable from the TAP-1000BT-SX
port TAP A connector into one port of the
Network Analysis Tool interface card.
5. Connect the other tap cable from the
TAP-1000BT-SX port TAP B connector into the
other port of the Network Analysis Tool interface
card.
Single Port Copper Tap
TTAAPP--11000000BBTT--SSXX
QQUUIICCKKIINNSSTTAALLLLAATTIIOONNGGUUIIDDEE
PN 2530025
August 2005
© 2005 Fluke Networks, Inc. All rights reserved. Printed in USA.
All product names are trademarks of their respective companies.
CCOONNTTAACCTTIINNGGFFLLUUKKEENNEETTWWOORRKKSS
Visit the Fluke Networks website
at www.flukenetworks.com.
Send email to: [email protected].
For operating assistance, sales, or service in the USA,
call 1-800-283-5853.
From other countries:
• Canada: 1-800-363-5853
• Europe: [phone]
• Beijing: [phone]
• Japan: [phone]
• Singapore: [phone]
• Anywhere in the world: [phone]
Visit our website for a complete list of phone numbers.
Limited Warranty & Limitation of Liability
Fluke Networks products will be free from defects in
material and workmanship for two years from the date
of purchase. Parts, accessories, product repairs and
services are warranted for 90 days. This warranty
does not cover disposable batteries, cable connector
tabs, cable insulation-displacement connectors, or
damage from accident, neglect, misuse, alteration,
contamination, or abnormal conditions of operation
or handling. Resellers are not authorized to extend
any other warranty on Fluke Networks’ behalf.
To obtain service during the warranty period, contact
your nearest Fluke Networks authorized service center
to obtain return authorization information, then send
your defective product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY.
NO OTHER WARRANTIES, SUCH AS FITNESS FOR
A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED.
FLUKE NETWORKS IS NOT LIABLE FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion
or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may
not apply to you.
FLUKE NETWORKS, INC. P.O. BOX 777 EVERETT, WA 98206-0777 USA
CCOOMMPPLLIIAANNCCEETTEESSTTIINNGG
CAUTION
Changes or modifications to this unit not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
CCEERRTTIIFFIICCAATTIIOONNSS
This equipment has been tested and found to
meet the radiated and conducted emission limits for
a Class B product of EN 55022 to the EMC Directive
89/336/EEC requirements.
This equipment has been tested and found to meet
the immunity levels for Class 1, tested to level 2
for EN 6100-4-2, tested to level 3 for EN 61000-4-3,
tested to level 2 for EN 61000-4-4, and tested to
level 3 for EN 61000-4-5 to the EN 50082-1
requirements and meets the Class A requirements
for EN 61000-3-2 and EN 61000-3-3.
This equipment has completed the Product Safety
Review and found to meet the Low Voltage Directive
72/23/EEC (1993) requirements.
Full Duplex
Network Cable
Full Duplex
Network Cable
Tap Cables
Distribution
Access Switch Network Analysis Tool