Flycam Equator ST-EQTR-01 User manual

1
Equator 3-Axis Handheld Gimbal Stabilizer
(ST-EQTR-01)
Assembly Manual
2 x Roll Axis Handle
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
What’s In The Box
1 x Dovetail Base
Mount with 2 x Rod
2 x L-Type Allen Keys
(Size:3/16”,5mm)
1 x 5/8" Baby
Pin Adaptor
4 x Height Adjustment Side Rod
2 x Side Handle Bar
2 x Height Adjustment Bracket
1 x Dovetail Plate
1 x Pan and Tilt Head
1 x Docking Bracket

2
Equator 3-Axis Handheld Setup
• Loosen both the knobs of the Pan Tilt Head
and mount it on a C-stand (Not Included).
• Aer aligning the Side Rod, ghten & secure
both the bolts back into the Pan Tilt Head
using an Allen key.
• Then properly ghten & secure both the
knobs of the Pan Tilt Head, as shown in the
image.
• Loosen both the bolts at the side of the Pan
Tilt Head with the help of an Allen key.
• Insert the Height Adjustment Side Rod into
the Pan Tilt Head and align the boom
posion using your nger.
• Similarly, aach the other Height Adjustment
Side Rod with the Pan Tilt Head, following the
same process.
Height Adjustment Side Rod Assembly

3
• Loosen both the knobs of the Height
Adjustment Bracket.
• Loosen the knob of the Roll Axis Handle, then
insert it in the Adjustment Bracket by aligning
them together.
• Insert the Adjustment Bracket into the rods of
the Dovetail Base by aligning the holes, as
shown in the image.
• Aer posioning the Adjustment Bracket and
the Dovetail Base parallel to each other,
ghten & secure them via both the knobs.
• Similarly, follow the same process to aach
the other Adjustment Bracket with dovetail
base.
• Tighten the knob aer inserng the handle
into the Adjustment Bracket.
NOTE: You can adjust the posion of the handle
according to you requirements.
Height Adjustment Bracket Assembly
Roll Axis Handle Assembly

4
• Similarly, follow the same process to aach
another Roll Axis Handle with Adjustment
Bracket.
NOTE: The handheld mode is more exible,
direct, fast and precise than Steadicam to
control the camera.
• Mount the Dovetail Base with the Roll Axis
Handle on the Side Adjustment Rod and
parallelly align the posion of the rods.
• Then secure the Roll Axis Handle by
ghtening both the knobs.
• Then pull the knob of the Pan Tilt Head &
unlock it to give it lng movement.
Features of Both Handle
Tension adjustment
knob
Rods equal align
Telescopic Rods
with Index Marking

5
• The three-axis Flycam Equator has a lng
range of ±25°.
NOTE: Flycam Equator is a three-axis
zero-gravity gimbal, with a lng range of ±25°
from center. Each with their own independent
locking knobs, the stabilizer provides ample
operaonal exibility.
• Loosen the back knob of the Pan Tilt Head to
facilitate panning movement.
• Loosen the tension adjustment knob to
facilitate rolling movement for the setup and
then ghten the knob back to lock the
posion.
NOTE: A tension adjustment knob helps you
balance the setup opmally.
• Align the Dovetail Plate to the Camera
(Not Included) then properly ghten and
secure it with the help of a screwdriver.
Dovetail Plate with Camera Assembly
Flycam Equator 3– axis Features
NOTE: Flycam Equator, with a panning range of
360° & an independent locking knob for it,
oers ample exibility in operaons.

6
• To secure & lock the Camera (Not Included)
to the plate, use the provided locking lever.
NOTE: To adjust the height of the Adjustment
Bracket, use the provided knob symbols
(H- High & L- Low).
• Loosen and remove the knob of the Side
Handle Bar.
• Insert the Side Handle Bar into the side hole
of the Docking Bracket and properly ghten it
with the help of the knob.
• Similarly, follow the same process to aach
the other Side Handle Bar with Docking
Bracket.
• Aer aaching the Docking Bracket and the
Side Handle Bars together, align & mount it
on a 5/8” Baby Pin (Not Included) via the
receiver at the base of the bracket.
H- High
L- low

7
YOUR FLYCAM EQUATOR 3-AXIS HANDHELD GIMBAL STABILIZER
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
• Aer aaching the Camera (Not Included) to
the plate, place it on top of the Dovetail Base.
• Then with the help of the provided knob of
the Docking Bracket, properly ghten and
secure the assembly.
NOTE: Mount the stabilizer on any C-Stand or
Light Stand via the 5/8” Baby Pin receiver at the
base of the docking bracket.
• It easily adapts to large cameras and has an
O’Connor Standard Quick Release Dovetail
Base Mount & Plate, ensuring quick camera
setup. A docking bracket designed to hold the
stabilizer in place lets you switch from
handheld-mobile shoong to xed-camera
shoong in no me.

8
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.