Forging Mount HY 9001 User manual

FULL-MOTION
TV WALL MOUNT
For 26 - 55”(66-140cm) TVs
Model HY 9001
M6
M4 M8
STEP 1-1
Select TV Screw Diameter
STEP 1-2 Select TV Screw Length
FLAT BACK ROUND BACK CABLESINSET HOLES
AB
Too Short
Too Long
Correct
88 lbs.
(40 kg)
Does your TV (including accessories)
weigth more than 88 lbs. ( 40 kg )?
— Perfect!
Y
— This mount is NOT compatible.
STEP 1-3 Measure Your TV Hole Pattern
If your TV has a flat back, AND you want your TV closer
to the wall, use the shorter screws (A).
Use the spacers and longer s crews
(B) to accommodate:
·Round/irregular back TVs
·TVs with inset mounting holes
·Extra space needed for cables CAUTION Verify
adequate thread
engagement with the screw/
washer/spacer combination
AND TV bracket .
- Too sho will not hold the TV.
- Too long will damage the TV.
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
you can see online:
www.forgingmount.com
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use.
WARNING Exceeding the weight
capacity can result in serious personal
injury or damage to equipment! It is the
installer's responsibility to make sure the
weight of the TV (with accessories) does
not exceed 88 lbs ( 40 kg ).
Drywall with
woo studs?
Perfect!
What is your wall made of?
Please read through these instructions completely to be sure you’re comfortable with
this easy install process. Also check your TV owner’s manual to see if there are any
special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, please contact US via email: [email protected]
CAUTION:
Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud/concrete walls DO NOT install into
drywall
●The wall must be capable of supporting ve times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly speci ed by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Solid concrete or
conc et block?
inch dimensions are approximate
100 mm = 10 cm≈ 4 in.
200 mm = 20 cm≈7 7/8 in.
300 mm = 30 cm≈11 3/4 in.
400 mm= 40 cm≈15 3/4 in.
x Height
Width mm m
STEP 1-4 Assemble Your TV Bracket
Based on your TV hole pattern measurements
from STEP 1-3 todetermine your
TV bracket configuration: A, B, C, D, E
W
H
75 mm= 7.5cm≈ 3 in.
Tools Needed
Hardware Included
WARNING: This product
contains small items that could
bea choking hazard if swallowed.
Before starting assembly,
verify all parts are included
and undamaged. If any parts
are missing or damaged, do
not return the damaged item to
your dealer; contact Customer
Service.
Never use damaged parts!
NOTE: Not all parts and
hardware included will be used.
Concrete Install
Hammer Drill Bit
3/8 in.
(10 mm)
Concrete
Wood Stud Install
AwlStud Finder
7/32 in.
( 5 mm)
Wood
Drill Bit
Pencil Screwdriver
Tape
Measure Electric
Drill
1/2 in.
(13 mm)
Socket
Wrench
Lag Bolts
5/16x2.5”
Ax3
concrete anchor
Cx3
Lag Bolt
Washers
Bx3
TV Screws
M4X12
Dx4
M6X15
Fx4
M8X15
Hx4
M4X30
Ex4
M6X30
Gx4
M8X45
Ix4
Spacers
L5MM
Kx4
L10MM
Lx4
TV Washers
3 holes
Jx4
M4 M6 M8
TV BracketArm and Wall Plate TV Bracket Extensions
01 x1
Level VELCRO TIE HDMI Cable
07 x105 x1 06 x5
02 x2 03 x2 04 x1
M6X8
Mx8
Ø6
Nx8
TV Extension Screws
Ø6
Px1 Qx1
Hex key
M6X10
Ox1
Securement screw
fi
fi
m
No
es
Getting Started
:
d
er
rt
:

2-1 2-2 2-3 2-4
Attach TV Bracket and extensions to TV
3 in. (75 mm)
7/32 in.
(5.0 mm)
S
STEP 2
Wall Plate Install ( Wood Stud)
CAUTION: Avoid potential personal injuries
and property damage!
●Drywall covering the wall must not exceed
5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION: Avoid potential personal injury
or property damage! All lag bolts 12 MUST BE
firmly tightened to prevent unwanted movement
of the wall plate
01 .
CAUTION: Ensure the wall plate is securely
fastened to the wall before continuing on to the
next step. In tall wall plate e
01 using lag bolt s
A and
washers B. Tighten the lag bolts
only until
they are pulled firmly a gainst the wall plate
01
Drill pilot holes using a 7/32 inch(5 mm ) diameter drill bit .
IMPORTANT:
Pilot holes must be drilled to a depth of 3
in. (75 mm) .
Be sure to drill into the center of the stud.
CAUTION: Avoid potential personal injuries and
property damage!
●Minimum solid concrete thickness: 8 in. (203 mm).
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 16 in
(406 mm).
●Mount wall plate 10 directly onto the concrete surface.
STEP 3
Wall Plate Install ( Solid Concrete or Concrete Block )
Position wall plate 01 at your
desired height. use Level to
level the wall plate , then
mark the two hole locations.
Drill three pilot holes using a 3/8 in.
(10 mm) masonry drill bit.
IMPORTANT: Pilot holes must be
drilled to a depth of 3 in (75 mm) .
Never drill into the mortar between blocks.
Min.
8 in.
(203 mm)
Min. 8 in.
(203 mm)
Min. 16 in.
(406 mm)
( 10x50mm) to the wall
CAUTION: Be sure the anchors are
seated flush with the concrete surface.
Install wall plate 01 with two washers A and
screws B
CAUTION:
Improper use could reduce the holding
power of screws B
. DO NOT over-tighten the screws.
Insertthree concrete anchors
s
01
3-1 3-2 3-3 3-4
Attach TV to the arm assembly
Hang the TV onto the arm assembly
by first hooking the hang tab
then resting the TV into place.
Avoid potential personal injury or property damage!
must be installed to secure the T
Loosen the nut with a wrench adjust the appropriate tilt Angle
and tighten the nut
V to the arm assembly
CAUT TILT ADJUSTMENTION:
s
01
s
H
a Flat Back
b Round Back / Extra Space
K J
D F H
L
E G I
s
04
s
H
s
04
s
02
s
03
s
04
: Ensure TV bracket is securely fastened before moving on to the next step.
IMPORTANT
CAUTION: Avoid potential personal injuries and property damage!
DO NOT use a power screwdriver for this step.
Made in China.
If you have any questions please feel free to contact us at
email: [email protected]
Position wall plate 01 at your
desired height. Level, then
mark the h h oleee locations.
s
05
Note Orientation
11 12
t r
C
J
05 05
05
05
CAB
Locate your stud. Verify and mark the center of s