Forging Mount HY9389-B User manual

M6
M4 M8
STEP 1-1
Select TV Screw Diameter
STEP 1-2 Select TV Screw Length
FLAT BACK ROUND BACK CABLESINSET HOLES
AB
Too Short
Too Long
Correct
99 lbs.
(45 kg)
Does your TV (including accessories)
weigth more than 99 lbs. ( 45 kg )?
— Perfect!
Y
— This mount is NOT compatible.
If your TV has a flat back, AND you want your TV closer
to the wall, use the shorter screws (A).
Use the spacers and longer s crews
(B) to accommodate:
·Round/irregular back TVs
·TVs with inset mounting holes
·Extra space needed for cables CAUTION Verify
adequate thread
engagement with the screw/
washer/spacer combination
AND TV bracket .
- Too sho will not hold the TV.
- Too long will damage the TV.
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
you can see online:
www.forgingmount.com
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use.
WARNING Exceeding the weight
capacity can result in serious personal
injury or damage to equipment! It is the
installer's responsibility to make sure the
weight of the TV (with accessories) does
not exceed 99 lbs ( 45 kg ).
Drywall with
woo studs?
Perfect!
What is your wall made of?
Please read through these instructions completely to be sure you’re comfortable with
this easy install process. Also check your TV owner’s manual to see if there are any
special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, please contact US via: [email protected]
CAUTION:
Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud/concrete walls DO NOT install into
drywall
●The wall must be capable of supporting ve times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly speci ed by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Solid concrete or
conc et block?
Tools Needed
Hardware Included
WARNING: This product
contains small items that could
bea choking hazard if swallowed.
Before starting assembly,
verify all parts are included
and undamaged. If any parts
are missing or damaged, do
not return the damaged item to
your dealer; contact Customer
Service.
Never use damaged parts!
NOTE: Not all parts and
hardware included will be used.
Concrete Install
Hammer Drill Bit
3/8 in.
(10 mm)
Concrete
Wood Stud Install
AwlStud Finder
7/32 in.
( 5 mm)
Wood
Drill Bit
Pencil Screwdriver
Tape
Measure Electric
Drill
1/2 in.
(13 mm)
Socket
Wrench
Lag Bolts
5/16x2.75”
Ax5
concrete anchor
Cx5
Lag Bolt
Washers
Bx5
TV Screws
M4X15
Dx4
M6X15
Fx4
M8X15
Hx4
M4X30
Ex4
M6X30
Gx4
M8X45
Ix4
Spacers
L5MM
Lx8
L10MM
Mx8
TV Washers
Jx4
Wall plate cover
Arm and Wall Plate TV Bracket
01 x1
HDMI Cable
07 x105 x1
wallplate template Level
04 x1
Cable Cover
06 x5
02 x2
03 x2
fi
fi
No
es
Getting Started
:
d
er
rt
:
LONG ARM
TV WALL MOUNT
Model HY9389-B
Nx1
Wrench
take out the wallplate covers from the wall plate
STEP 1-3 Attach the TV plate to the arm assembly
M
4
/
M
5
M
6
/
M
8
Kx4
Specification Sheet 30”-2.36”
11.2” 16.93”
23.6”-5.9”

05
16 in.
(406 mm)
2-1 2-2 2-3 2-4
STEP 4 Attach TV Brackets to TV back STEP 5 Attach TV to the arm assembly
Made in China.
Position the template at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the holes.
Drill pilot holes using a 7/32 in (5.5mm) diameter drill bit.
of 3 in.(75 mm).Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth
CAUTION: property damage!
●Minimum solid concrete thickness: 8 in. (203 mm).
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 16 in
(406 mm).
●Mount wall plate directly onto the concrete surface.
Position template 04 at your
desired height. Level, then
mark the five hole locations.
Drill five pilot holes using a 3/8 in.
(10 mm) masonry drill bit.
Min.
8 in.
(203 mm)
Min. 8 in.
(203 mm)
Min. 16 in.
(406 mm)
CAUTION: Be sure the anchors are
seated flush with the concrete surface.
Install wall plate
DO NOT over-tighten the screws.
and screws
holding power of screws
with five washers
01
IMPORTANT : Ensure TV bracket is securely fastened before moving on to the next step.
CAUTION:Avoid potential personal injuries and property damage!
DO NOT use a power screwdriver for this step
STEP 2 Wall Plate Install( Wood Stud )
STEP 3 Wall Plate Install( Solid Concrete or Concrete Block )
½ x 3½ in. (38 x 89 mm)
A MUST BE
CAUTION: Avoid potential personal injuries
and property damage!
●Drywall covering the wall must not exceed
5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1
CAUTION: A
01 .
void potential personal injury
or property damage! All lag bolts
firmly tightened to prevent unwanted
movement of the wall plate
CAUTION: Ensure the wall plate is securely
fastened to the wall before continuing on to the
next step. the studs by finding the stud edges using an awl,
a thin nail, or an edge-to-edge stud finder.
Locate your studs. Verify and mark the center of 04
Install wall plate
washers
they are pulled firmly a gainst the wall plate
.Tighten the lag bolts only until
using lag bolt and
01
01
01
A
B
B
22
B
A
3 in. (75mm)
7/32 in.
(5.5 mm)
Avoid potential personal injuries and
UP
3-1 3-2 3-3
04
Min. 16 in.
(406 mm)
drilled to a depth of 3 in ( 75 mm ).
Never drill into the mortar between blocks.
IMPORTANT:Pilot holes must be
04
C
Insert five concrete anchors
( 10x60mm ) to the wall
CAUTION: Improper use could reduce the
A
aFlat Back
JD F H
bRound Back/Extra Space
JK
M
E G I
CAUTION: Avoid potential personal injury or property damage!
Make sure your locking screws are tightened BEHIND the mounting bar 05 ,
so the TV is securely fastened in place.
STEP 6 installation wallplate cover
and cable management Loosen the nut with a wrench to adjust the appropriate tilt
Angle and tighten the nut
STEP 7 Tilt and level adjustment
N
Tilt adjusting Leveling
Attach TV to the mounting bar
A
B
3-3
01 A
B
L
K
Cable management
Use screwdriver to adjust the 2 screws for TV level