Fresh INTELLIVENT 2.0 User manual

EN
DE
FR
ES
NL
IT
Designed and manufactured
by Fresh in Sweden
MANUAL
INTELLIVENT
®
2.0

Thank you for choosing this product from Fresh.
Before installing and using the fan, read through this
manual / these instructions for use.
Then keep it safe so that you can use it for reference in
future.
Warning!
This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
are supervised or have been given instruction concerning
use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the product.
2

CONTENTS
4 Description of functions
5 Installation guide
1 Contents
2 Installation
3 Connection
4 Installation options
5 Connecting a pull cord switch
6 Factory setting
7 Setting functions
10 Advanced functions
• Setting humidity sensitivity mode
• Pause function with momentary switch
12 LED indicators
13 Maintenance
15 Warranty
15 Recycling
16 Accessories
17 Technical data
18 Troubleshooting guide
EN
3

DESCRIPTION OF FUNCTIONS
• Automatic moisture detection system
Fresh Intellivent is equipped with fully automatic humid-
ity control, which means the fan learns to run only when
it can make a dierence.
• Timer
Selectable delay time – 5, 15 or 30 minutes.
• Speed control
The integral speed control allows you to adjust the noise
level and capacity to meet your needs.
• Continuous operation
Leave the fan running continuously if you need basic
ventilation in the home.
This also eliminates the risk of draughts in case of wall
mounting.
• Airing function
If the fan has been inactive for 26 hours, an airing
programme will run for 60 minutes.
• Pause function
The fan can be paused for one hour using the power
cord.
• Multi-pole switch
The fan is tted with a multi-pole switch, which means
that an external switch is not required.
• LED indicators
A light-emitting diode with three dierent colours
indicates which mode the fan is in at any one time.
• 12-volt motor
The motor is a long-life motor, with a life span of approx.
60,000 hours. This type of motor also runs silently.
4

INSTALLATIONGUIDE
1 Contents
The packaging should contain the following:
• Fan
• 2 adapters, 1 x Ø98 mm and 1 x Ø118 mm
• Manual
• Accessory bag with 4 screws and plugs, a pull cord with
toggle, and insulation for the standard cable type (FK)
2 Installation
The fan can be installed on a wall or on a ceiling. See the
diagram below for installation dimensions. The fan must
not be installed in an environment where the temperature
exceeds 50°C. Attach an appropriate adapter to the fan's
chassis, Ø98 (1) for a Ø100 duct or Ø118 (2) for a Ø125 duct.
The fan can also be installed and
used without an adapter, so
that it is mounted completely
on the surface, e.g. in the case
of ducts less than Ø98.
When installing the fan, check that there is a seal between
the pipe/duct and wall/ceiling to prevent humid air from
penetrating the wall or ceiling. Use the accompanying
screw and plug, if necessary.
EN
Ø100 alt. Ø125
45
55
Min 120
Min 80
45
55
#124
Alt. x4
x4
1
2
5

Cable entries
A=surface
B=concealed
3 Wiring
• Installation work should be performed by a qualied
electrician.
• The fan is double insulated and must not be earthed.
• The fan is tted with a multi-pole switch and does not
require a pre-wired external switch.
1 Push the multi-pole switch up to position 0 – OFF.
2 The cable can be installed either along the surface using
entries A in the chassis or concealed using the B inlets
in the chassis. Both options are shown below. Use the
insulating sleeve supplied for the cable (FK).
3 If you use any of the B inlets, remove the concealed
round plastic cover by tapping inside the break-o
notch from the inside out to the back with a screwdriver,
for example.
A
A
A
A
B
B
B
B
ON
OFF
6

4 Installation options
The fan can be installed in any of three ways
depending on the desired function, as detailed below:
1 Humidity control only, see diagram 1
The fan is connected to constant phase (L) and
neutral (N) for automatic humidity control.
The timer can be activated manually by installing a pull
cord and pulling it (see page 8).
2 Humidity control + timer with light switch, see
diagram 2
The fan is connected to constant phase (L) and
neutral (N) for automatic humidity control.
Switched live (SL) is connected to activate the fan's
timer, i.e. when the bathroom light is switched on, cur-
rent is present at switched live. This option provides a
90-second start delay.
3 Humidity control + timer with retractive switch, see
diagram 3
The fan is connected to constant phase (L) and
neutral (N) for automatic humidity control.
Switched live (SL) is connected to activate the fan's timer
using a retractive switch.
This option gives direct start-up of the fan.
Wiring diagram
EN
1 2 3
SL N L SL N L SL N L
L
N
L
N
L
N
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
1 2 3
SL N L SL N L SL N L
L
N
L
N
L
N
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
7

5 Connecting the pull cord switch
A pull cord can be installed for activating the timer
manually or for pausing the fan. Remove the mounting
plate using a screwdriver, for example, and thread the
accompanying pull cord through the hole.
• Once installation is complete, push the safety switch
down to position I – ON, to make the fan active again.
When the fan is connected to the power supply, it performs a
self-test where electronics, LEDs and operation of the motor
are all tested. The fan is now ready for use.
NB!
Use an ordinary round le to
create a smooth cut-out at
a suitable place in the front
cover.
Do NOT use pliers or similar
tools, as these may cause the
cover to crack.
8

6 Factory setting
• timer – 5 minutes
• humidity speed – silent (70% of max.)
• timer speed – 70% of max.
• constant operation – o
Restore factory settings
Hold the S-button in for
a minimum of 5 seconds.
7 Setting functions
Possible adaptation to meet your needs:
1. Setting fan speed for timer operation.
Press the S-button until the timer light comes on.
Use the SPEED buttons to set the speed.
Restore the factory default timer speed by pressing both
the SPEED buttons simultaneously.
2. Delay time
Set the timer to 5, 15 or 30 minutes.
3. Humidity mode / humidity
Set to silent or max. capacity – small or large bathroom.
4. Continuous operation
Press the S-button until the "CONSTANT" light comes
on. Select the fan speed using the SPEED buttons.
To turn o continuous operation: press the S-button
until the "CONSTANT" light goes o.
EN
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
9

ADVANCED FUNCTIONS
Selecting humidity sensitivity mode
Bathroom climates may vary depending on a number of
factors: room size, the presence of any natural draught
ventilation, temperature, etc. These factors may have a
bearing on fan humidity response, causing it to start too
quickly or too slowly.
The factory setting is position 2: normal humidity
response, which works best in most cases.
There is also the option of
completely switching o the
humidity function.
1) Press the Speed + and
Humidity mode buttons
simultaneously (the blue and
yellow LEDs ash quickly).
Press the Humidity Mode but-
ton until the desired humidity
sensitivity mode is selected.
Position 1: the Silent LED comes
on – fast humidity response.
Position 2: the Max LED comes
on – normal humidity response.
Position 3: The Silent and Max
LEDs come on together – slow
humidity response.
Position 4: Both the Silent and
Max LEDs stay o – humidity
control is deactivated.
2) Press the Speed + and
Humidity Mode buttons at the
same time (The blue and yellow
LEDs stop ashing).
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
TIMER
HUMIDITY
TIMER
CONSTANT
5
15
30
SPEED
SILENT
MAX
S
MIN
10