Fri-Jado TDR 5 M User manual

WWW.FRIJADO.COM Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
MODELS
TDR 5 M
TDR 8 M
TDW 5 M
TDW 8 M
TDR 5 P eco
TDR 8 P eco
TDW 5 P
TDW 8 P
INSTALLATION MANUAL
TDR - ROTISSERIE OVEN MODELS
TDW - WARMER MODELS
- NOTICE -
This manual is prepared for the use of trained Service Technicians and
should not be used by those not properly qualified. If you have atten-
ded a trianing for this product, you may be qualified to perform all the
procedures in this manual.
This manual is not intended to be all encompassing. If you have not
attended training for this product, you should read, in its entirety, the
repair procedure you wish to performto determine if you have the ne-
cessary tools, instruments and skills required to perform the procedure.
Procedures for which you do not have the necessary tools, instruments
and skills should be performed by a trained technician.
Reproduction or other use of this Manual, without the express written
consent of Fri-Jado, is prohibited.
Model TDR5 M Model TDR8 Peco

Page 2 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
EMPTY PAGE

TABLE OF CONTENTS
Page 3
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
Versions
Version Issue date
dd/mm/yy
Remarks
07/2010 01/07/2010 First release.
02/2014 01/02/2014 TDR P and TDRW added.

Page 4 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
Index .......................................................................................................................................................... 4
General technical data.............................................................................................................................. 5
Technical data ........................................................................................................................................ 5
Installation procedures............................................................................................................................. 6
Unpacking the unit................................................................................................................................ 6
Location.................................................................................................................................................. 7
Location.................................................................................................................................................. 8
Electrical supply ..................................................................................................................................... 8
Legs / Castors.......................................................................................................................................... 9
Tethering of the unit ............................................................................................................................. 9
Test run................................................................................................................................................. 10
Extraction of the rotisserie.................................................................................................................. 10
Instructions for operators.................................................................................................................... 10
Placing and connecting of the units...................................................................................................... 12
TDR 5 M................................................................................................................................................ 12
TDR 5 P ................................................................................................................................................. 13
TDR 8 M ............................................................................................................................................... 14
TDR 8 P ................................................................................................................................................. 15
TDR 5 + 5 M.......................................................................................................................................... 16
TDR 5 + 5 P ........................................................................................................................................... 17
TDR 8 + 8 M.......................................................................................................................................... 18
TDR 8 + 8 P ........................................................................................................................................... 19
TDRW 5 M and TDRW 5 P.................................................................................................................... 20
TDRW 8 M and TDRW 8 P.................................................................................................................... 21
TDR 5 M and TDR 5 P on base............................................................................................................. 22
TDR 8 M and TDR 8 P on base............................................................................................................. 23
TDW 5 M and TDW 5 P........................................................................................................................ 24
TDW 8 M and TDW 8 P........................................................................................................................ 25
INDEX

Page 5
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
GENERAL TECHNICAL DATA
GENERAL TECHNICAL DATA
TECHNICAL DATA
This manual covers the TDR series rotisserie ovens and the TDW series warmers. Ovens and
warming cabinets come in two sizes. Ovens and cabinets will alsobe delivered in stacked ver
sions.
• TDR 5 – Oven with five spits ( 15 to 20 chickens )
• TDR 8 – Oven with eight spits ( 32 to 40 chickens )
• TDW 5 - Warming cabinet for 25 to 30 chickens
• TDW 8 - Warming cabinet for 35 to 40 chickens
All of the information, illustrations and specifications contained in this manual are based on
the latest product information available at the time of printing.
Type TDR 5 TDRW 5 TDR 8 TDRW 8 TDW 5 TDW 8
Power (W) 6600 9400 10500 14000 2800 3500
Fuses needed with power connec-
tion 400 V, 3N ~50…60 Hz
( 3 phases with zero )
3x 16 A 3x 16 A 3x 16 A 3x 32 A - -
Fuses needed with power connec-
tion 200 or 230 V, 3 ~50…60 Hz
( 3 phases without zero )
3x 20A 3x 32 A 3x 32 A 3x 35 A - -
Fuses needed with power connec-
tion 230 V, 1N ~50…60 Hz
( 1 phase with zero )
- - - - 1x 16 A 1x 16 A
Standard plug from factory 5-pole
Acc IEC309 and CEE-form
16 A
3P+N+E
16 A
3P+N+E
16 A
3P+N+E
32 A
3P+N+E - -
Standard plug from factory single
pole
_ _ _ _ 2-pole
earthed
plug 16 A
2-pole
earthed
plug 16 A
Net weight (kg) 130 235 185 340 100 150
Gross weight (kg) 160 275 216 390 120 176
Height (mm) 910 1790 1065 2095 910 1065
Width (mm) 835 835 995 995 835 995
Depth (mm) 710 710 830 830 660 830
• Standard set of tools.
• Metric wrenches, sockets and hex socket key wrenches.
• Multi-meter and AC current clamp meter.
• Temperature tester.
• Insulation value tester (Megger).
• Field Service Grounding Kit.

Page 6 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
• Unpacking of the unit.
• Remove the pallet under the unit with the help of a fork lift.
• Put the unit on his location.
• Check if there is enough free space around the unit (see installation drawing).
• Check the electrical supply.
• Tethering of the unit.
• Make a test run on 250°C.
• Give instructions to the operator.
UNPACKING THE UNIT
Immediately after unpacking the oven, check for possible shipping damage. If the oven is
found to be damaged, save the packaging material and contact the carrier within 15 days of
delivery.

Page 7
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
The standard way to remove the rotisserie or
warmer from a pallet is with a fork lift. See
pictures. Open door and remove the drawer.
Lift the unit from pallet and put the unit in
its place.
Note: when lifting a stacked unit, always use
the drawer of the bottom unit.
Another possibility is to disassemble the pal-
let. For the pallet of the TDR 8 follow the
procedure on the drawing.
LOCATION
To avoid short-circuiting, the units may not be
used outdoors. Placing under a screen is allowed.
REMOVAL OF PALLET

Page 8 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
Prior to installation, test the electrical service to assure that it agrees with the specifications
on the machine data plate located on the right side panel near the controls. The connecting
cable for the unit must be equipped with an approved plug connection. If use is to be made
of a permanent connection, the connecting cable must be connected to a manual on/off
switch that is installed near the unit in a clear visible manner.
ELECTRICAL SUPPLY
IMPORTANT: Make sure you lea-
ve sufficient space around the
rotisserie or warmer to easily
remove or insert the rotor. If the
base has (rotating) wheels, the
floor on which it rests must be
level.
LOCATION
The oven must be installed on a level surface. The installation location must allow adequate
clearances for servicing and proper operation.
1 2 3 4 5 6
L2L1 L3 N
For a 3-phase 400 V ~ circuit with neutral, the
unit must be connected according to the figure
below.
400 V, 3N ~ 50...60 Hz
1 2 3 4 5 6
N
L1
For a single-phase 200 V or 230 V ~ circuit with
neutral, the unit must be connected according to
the figure below.
200 V or 230 V, 1N ~ 50...60 Hz
1 2 3 4 5 6
L2L1 L3
For a 3-phase 200 V or 230 V ~ circuit without
neutral, the unit must be connected according to
the figure below.
200 V or 230 V, 3 ~ 50...60 Hz

Page 9
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
Each oven and warmer is furnished on 50mm legs. Stacked models are furnished with 2 swi-
vel and 2 locking swivel castors. A castor-equipped stand with convenient storage drawer is
available; the oven is mounted on top of the stand.
LEGS / CASTORS
TETHERING OF THE UNIT
(For model TDR 5 and TDR 8 units when stacked or placed on base with castors)
Warning: Safety standards require that, when this appliance is properly connected to the
electrical power supply using flexible conduit, adequate means be provided to limit move-
ment of the appliance without depending on or transmitting stress to the electrical conduit.
This means that, as part of the installation, the base or bottom unit of stacked models must
be secured to the building structure (typically either wall or floor) to limit the movement of
the appliance and, thus, helping to prevent damage to the conduit during cleaning, main-
tenance and service operations.
A tether bracket, as shown on the drawing below, is provided with the base or stacking kit.
Based on the routing of the flexible conduit, the bracket must be installed along with the
caster to one corner of the base using the hardware provided. The remaining open hole in
the center of the tether bracket is to be used to secure one end of the tether (locally supplied
chain, cable, etc.). The other end of the tether is to be secured to an anchoring point in the
building structure.
Note: Length of tether must be shorter than the flexible conduit to make sure that during
appliance movement, no stress is transmitted to the conduit.
Warning: Following installation, check to confirm that, when the appliance is moved to the
limits of the tether in each direction, no stress is transmitted to the electrical conduit.

Page 10 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
After installation of the rotisserie or warmer, the operator of the unit has to be instructed.
The instruction has to cover the following subjects:
• Programming and options.
• Working of the unit.
• Free space of unit for cooling of drive motor and blowers.
• Run through the user manual.
• Periodical maintenance:
o Cleaning of fan plate every month.
• How to react for information or service calls.
INSTRUCTIONS FOR OPERATORS
The oven must be burned in to release any odours that might result from heating the new
oven surfaces. Operate the oven at maximum temperature setting of 250°C for 30 minutes
and the warmer on 100°C. Smoke with an unplaesant odour will normally be given off du-
ring this burn-in period.
TEST RUN
Although an extraction hood is not prescribed, it could be desired that a hood is placed over
the rotisserie. The TDR 8 produces about 10 m³ water vapour and the TDR 5 about 6 m³.
When placing the rotisserie under an extraction hood you have to consider the following
guide lines:
- The minimum capacity of the extraction hood has to be 800 m³/h.
- The extraction hood has to extend minimum by 20 cm on all sides of the rotisserie.
- The extraction hood has to have a free hight, above the rotisserie, of a minimum of 30 cm.
- The rotisserie has to be accessible for service purposes.
- The extraction hood has to be sloping on the inside for the condensation to run down.
Around the hood there has to be a gutter with a connection for the water to run down a
drain.
EXTRACTION OF THE ROTISSERIE

Page 11
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
INSTALLATION PROCEDURES
EMPTY PAGEEMPTY PAGE

Page 12 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
Description belonging to the lables on the drawings
Label Description
1 Power cable, length 2,2 meters *
2 Exhaust opening
3 Space between a rotisserie and a wall or ceiling
4 Location for socket
*) length is measured from the point where the cables coms out of the unit
TDR 5 M
PLACING AND CONNECTING OF THE UNITS

Page 13
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 5 P

Page 14 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 8 M

Page 15
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 8 P

Page 16 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 5 + 5 M

Page 17
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 5 + 5 P

Page 18 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 8 + 8 M

Page 19
Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDR 8 + 8 P

Page 20 Installation Manual TDR5/8 TDW 5/8 form 9123825 rev. 02/2014
PLACING AND CONNECTING
TDRW 5 M AND TDRW 5 P