Fri-Jado TDR 5 M User manual

USA
WWW.FRIJADO.COM Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION MANUAL
- NOTICE -
This manual is prepared for the use of trained Service Technicians and
should not be used by those not properly qualified. If you have atten-
ded a training for this product, you may be qualified to perform all the
procedures in this manual.
This manual is not intended to be all encompassing. If you have not
attended training for this product, you should read, in its entirety, the
repair procedure you wish to perform to determine if you have the ne-
cessary tools, instruments and skills required to perform the procedure.
Procedures for which you do not have the necessary tools, instruments
and skills should be performed by a trained technician.
Reproduction or other use of this Manual, without the express written
consent of Fri-Jado, is prohibited.
TDR - ROTISSERIE OVEN MODELS
TDW - WARMER MODELS
MODELS
TDR 5 M
TDR 8 M
TDW 5 M
TDW 8 M
TDR 5 P eco
TDR 8 P eco
TDW 5 P
TDW 8 P
Model TDR 5 M Model TDR 8 Peco

Page 2 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014

TABLE OF CONTENTS
Page 3
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
Versions
Version Issue date
dd/mm/yy
Remarks
03/2012 01/03/2012 First release.
02/2014 01/02/2014 TDR P and TDRW added.

Page 4 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
Index .......................................................................................................................................................... 4
General technical data.............................................................................................................................. 5
Installation procedures............................................................................................................................. 6
Unpacking the unit................................................................................................................................ 6
Location.................................................................................................................................................. 7
Electrical supply ..................................................................................................................................... 8
Legs / Castors.......................................................................................................................................... 9
Tethering of the unit ............................................................................................................................. 9
Test run................................................................................................................................................. 10
Heat extraction of the rotisserie......................................................................................................... 10
Instructions for operators.................................................................................................................... 10
Placing and connecting of the models .................................................................................................. 12
TDR 5 M Pass Through ........................................................................................................................ 12
TDR 5 P Pass Through .......................................................................................................................... 13
TDR 8 M Pass Through......................................................................................................................... 14
TDR 8 P Pass Through .......................................................................................................................... 15
TDR 5 + 5 M Pass Through................................................................................................................... 16
TDR 5 + 5 P Pass Through .................................................................................................................... 17
TDR 8 + 8 M Pass Through................................................................................................................... 18
TDR 8 + 8 P Pass Through .................................................................................................................... 19
TDRW 5 M Pass Through ..................................................................................................................... 20
TDRW 5 P Pass Through....................................................................................................................... 21
TDRW 8 M Pass Through ..................................................................................................................... 22
TDRW 8 P Pass Through....................................................................................................................... 23
TDR 5 M and TDR 5 P Pass Through on base...................................................................................... 24
TDR 8 M and TDR 8 P Pass Through on base...................................................................................... 25
TDW 5 M Pass Through ....................................................................................................................... 26
TDW 5 P Pass Through......................................................................................................................... 27
TDW 8 M Pass Through ....................................................................................................................... 28
TDW 8 P Pass Through......................................................................................................................... 29
INDEX

Page 5Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
GENERAL TECHNICAL DATA
GENERAL TECHNICAL DATA
This manual covers the TDR series rotisserie ovens and the TDW series warmers. Ovens and
warming cabinets come in two sizes. Ovens and warmers will also be delivered in stacked
versions.
• TDR5–Ovenwith5spits(15to20chickens)or5baskets(15chickens).
• TDR8-Ovenwith8spits(28to35chickens)or7baskets(28chickens).
• TDW5-Warmingcabinet25to30chickens.
• TDW8-Warmingcabinet35to40chickens.
Alloftheinformation,illustrationsandspecicationscontainedinthismanualarebasedon
thelatestproductinformationavailableatthetimeofprinting.
Type TDR 5 TDW 5 TDR 7 TDW 7
Power(W) 6600 2800 10500 3500
Fusesneededwithpowerconnec-
tion208V,3~60Hz
(3phaseswithoutzero)
3x20A _3x40A 3x20A
Fusesneededwithpowerconnec-
tion208V,1N~60Hz
(1phasewithzero)
_1x15A _ _
Standardplugfromfactory NEMA15-30P NEMA6-15P NEMA15-50P NEMA15-20P
Stackedcabinets:eachcabinetcomeswithseparatepowercord!!
Netweight(lbs) 287 220 408 331
Grossweight(lbs) 335 265 476 388
Height(inch) 353/4” 353/4” 413/4” 413/4”
Width(inch) 33” 33” 391/4” 391/4”
Depth(inch) 303/8” 303/8” 35” 35”
• Standardsetoftools.
• Metricwrenches,socketsandhexsocketkeywrenches.
• Multi-meterandACcurrentclampmeter.
• Temperaturetester.
• Insulationvaluetester(Megger).
• FieldServiceGroundingKit.
X
Y
G
Z
G
X
Y
G
Z
XY
G
Z

Page 6 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
• Unpackingoftheunit.
• Removethepalletundertheunitwiththehelpofaforklift.
• Puttheunitonhislocation.
• Checkifthereisenoughfreespacearoundtheunit(seeinstallationdrawing).
• Checktheelectricalsupply.
• Tetheringoftheunit.
• TDR:Makeatestrunon482°F.
• TDW:Makeatestrunon210°F.
•  Giveinstructionstotheoperator.
UNPACKING THE UNIT
Immediatelyafterunpackingtheoven,checkforpossibleshippingdamage.Iftheovenisfound
tobedamaged,savethepackagingmaterialandcontactthecarrierwithin15daysofdelivery.

Page 7
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION PROCEDURES
LOCATION
Thestandardwaytoremovetherotisserieor
warmerfromapalletiswithaforklift.See
pictures.Opendoorandremovethedrawer.
Lifttheunitfrompalletandputtheunitin
itsplace.
Note: when lifting a stacked unit, always use
the drawer of the bottom unit.
Anotherpossibilityistodisassemblethepal-
let.ForthepalletoftheTDR8followthe
procedureonthephoto.
REMOVAL OF PALLET
Toavoidshort-circuiting,theunitsmaynotbe
usedoutdoors.Placingunderascreenisallo-
wed.

1 2 3
NL1
1 2 3
L2L1 L3
Page 8 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION PROCEDURES
Priortoinstallation,testtheelectricalservicetoassurethatitcorrespondswiththespecicati-
onsonthemachinedataplatelocatedontherightsidepanelnearthecontrols.Theconnecting
cablefortheunitmustbeequippedwithanapprovedplugconnection.Ifuseistobemadeofa
permanentconnection,theconnectingcablemustbeconnectedtoamanualon/offswitchthat
isinstalledneartheunitinaclearvisiblemanner.
ELECTRICAL SUPPLY
IMPORTANT: Makesureyoulea-
vesufcientspacearoundthe
rotisserieorwarmertoeasily
removeorinserttherotor.Ifthe
basehas(rotating)wheels,the
ooronwhichitrestsmustbe
level.
Theovenmustbeinstalledonalevelsurface.Theinstallationlocationmustallowadequate
clearancesforservicingandproperoperation.
Theconnectingcablefortheunitmustbeequippedwithanapprovedplugconnection.Ifuse
istobemadeofapermanentconnection,theconnectingcablemustbeconnectedtoamanual
on/offswitchthatisinstalledneartheunitinaclearvisiblemanner.
For a single-phase 208 V ~ circuit with neutral,
the unit must be connected according to the
figure below.
For a 3-phase 208 V ~ circuit without neutral,
the unit must be connected according to the
figure below.
208 V, 1N ~ 50...60 Hz208 V, 3 ~ 50...60 Hz

Page 9
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION PROCEDURES
Eachovenandwarmerisfurnishedon115/16”legs.Stackedmodelsarefurnishedwith2swivel
and2lockingswivelcastors.Acastor-equippedstandwithconvenientstoragedrawerisavaila-
ble;theovenismountedontopofthestand.
LEGS / CASTORS
TETHERING OF THE UNIT
(FormodelTDR5andTDR8unitswhenstackedorplacedonbasewithcastors)
Warning:Safetystandardsrequirethat,whenthisapplianceisproperlyconnectedtotheelec-
tricalpowersupplyusingexibleconduit,adequatemeansbeprovidedtolimitmovementof
theappliancewithoutdependingonortransmittingstresstotheelectricalconduit.Thismeans
that,aspartoftheinstallation,thebaseorbottomunitofstackedmodelsmustbesecuredto
thebuildingstructure(typicallyeitherwalloroor)tolimitthemovementoftheappliance
and,thus,helpingtopreventdamagetotheconduitduringcleaning,maintenanceandservice
operations.
Atetherbracket,asshownonthedrawingbelow,isprovidedwiththebaseorstackingkit.
Basedontheroutingoftheexibleconduit,thebracketmustbeinstalledalongwiththecaster
toonecornerofthebaseusingthehardwareprovided.Theremainingopenholeinthecenter
ofthetetherbracketistobeusedtosecureoneendofthetether(locallysuppliedchain,cable,
etc.).Theotherendofthetetheristobesecuredtoananchoringpointinthebuildingstruc-
ture.
Note: Length of tether must be shorter than the flexible conduit to make sure that during appli-
ance movement, no stress is transmitted to the conduit.
Warning:Followinginstallation,checktoconrmthat,whentheapplianceismovedtothe
limitsofthetetherineachdirection,nostressistransmittedtotheelectricalconduit.

Page 10 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
INSTALLATION PROCEDURES
Afterinstallationoftherotisserieorwarmer,theoperatoroftheunithastobeinstructed.
Theinstructionhastocoverthefollowingsubjects:
• Programmingandoptions.
• Workingoftheunit.
• Freespaceofunitforcoolingofdrivemotorandblowers.
• Reviewtheusermanual.
• Periodicalmaintenance:
 o Cleaningoffanplateeverymonth.
• Howtoreactforinformationorservicecalls.
INSTRUCTIONS FOR OPERATORS
Theovenmustbeburnedintoreleaseanyodorsthatmightresultfromheatingthenewoven
surfaces.Operatetheovenatmaximumtemperaturesettingof482°Ffor30minutesandthe
warmeron210°F.Smokewithanunplaesantodourwillnormallybegivenoffduringthisburn-
inperiod.
TEST RUN
Althoughanextractionhoodisnotprescribed,itcouldbedesiredthatahoodisplacedover
therotisserie.TheTDR8producesabout350cfwatervapourandtheTDR5about200cf.When
placingtherotisserieunderanextractionhoodyouhavetoconsiderthefollowingguidelines:
-Theminimumcapacityoftheextractionhoodhastobe25000cf/h.
-Theextractionhoodhastoextendminimumby8”onallsidesoftherotisserie.
-Theextractionhoodhastohaveafreehight,abovetherotisserie,ofaminimumof12”.
-Therotisseriehastobeaccessibleforservicepurposes.
-Theextractionhoodhastobeslopingontheinsideforthecondensationtorundown.Around
thehoodtherehastobeagutterwithaconnectionforthewatertorundownadrain.
HEAT EXTRACTION OF THE ROTISSERIE

Page 11
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING

Page 12 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
Description belonging to the lables on the drawings
Label Description
1 Power cable, length 70” *
2 Exhaust opening
3 Space between a rotisserie and a wall or ceiling
4 Location for socket
*) length is measured from the point where the cables coms out of the unit
TDR 5 M PASS THROUGH
PLACING AND CONNECTING OF THE MODELS

Page 13
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 5 P PASS THROUGH

Page 14 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 8 M PASS THROUGH

Page 15
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 8 P PASS THROUGH

Page 16 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 5 + 5 M PASS THROUGH

Page 17
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 5 + 5 P PASS THROUGH

Page 18 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 8 + 8 M PASS THROUGH

Page 19
Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDR 8 + 8 P PASS THROUGH

Page 20 Installation Manual TDR5/8 TDW 5/8 form 9123904 rev. 02/2014
PLACING AND CONNECTING
TDRW 5 M PASS THROUGH