FRIEDLAND Libra+ Push Quick start guide

1
Contents
Checking pack contents..................... Pg. 2
Safety.................................................
Quick start..........................................
Open push.......................................... Pg. 3
Fit battery .........................................
Mount push .......................................
Troubleshooting.................................. Pg. 4
Specifications..................................... Pg. 5
Disposal and recycling.......................
Guarantee..........................................
Declaration.........................................
Installation and Use
Libra + Push
ENGLISH

2
Libra+ Push
Thank you for choosing this Friedland product. Please use the following instructions to
ensure correct installation and use. Keep these notes in a safe place for future reference.
Unpack your push and identify the following parts:
●Bell push
●CR2032 battery for bell push
●2 x fixing screws for push
●Adhesive pad
You will need:
●A4mm cross-head screwdriver
● Asmall flat bladed screwdriver
Checking pack contents
Before proceeding with the installation,
please note the following safety warnings:
¬●Always follow the manufacturer’s advice
when using power tools and wear suitable
protective equipment (e.g. safety goggles)
when drilling holes etc.
¬●Before drilling holes in walls, check for
hidden electricity cables and water pipes,
the use of a cable/pipe locater maybe
advisable if in doubt.
Safety
You need to do the following to get started:
●Open the bell push
●Fit the push battery
Follow the programming procedure for your
Libra+ chime.
Quick start

3
Insert a flat bladed screwdriver
into the slot A at the base of the
push. Carefully lever the cover
and base apart (Fig. 1).
Open the bell push
A
Fig. 1
Insert the CR2032 coin cell. Ensure the face
marked ‘+’ is uppermost (Fig. 2).
To fit the push battery
Fig. 2 CR2023
+
Mount using either the double
sided adhesive pad, or the
screws provided (see Fig 3).
Test your push before fixing.
Avoid fixing to metal structures.
Mount the bell push
Fig. 3

4
A ‘beep’ sound is heard in learn mode…
¬●The push you are programming has already been learnt by the chime.
¬●If you want to change the icon associated with the push, use the un-learn procedure, then
programme the push again.
Two ‘beep’ sounds are heard after the normal chime sound…
¬●This indicates a low battery in the bell push that activated the chime. Fit a new battery, type CR2032.
When the bell push is operated, the amber confidence light does not turn on, or is only
on for a short time…
¬●In normal operation, the amber light will turn on for 1 second. When the battery is weak,
the light will only turn on for a short time. Fit a new battery, type CR2032.
The chime does not work…
●Check that the batteries are the correct type. Only use alkaline batteries.
●Check that the batteries are fitted correctly.
●The chime could be out of range of the bell push. Try the chime in a different location.
●The chime might not have learnt the identity of the bell push. Follow the programming procedure.
The chime does not sound…
●Check that the volume control is not at the minimum setting.
Range is reduced…
●Metal structures, including uPVC door frames can reduce the range of the product.
Avoid mounting the push or chime on or near metal structures.
●Other equipment can cause radio interference that affects your chime.
●Walls and ceilings will reduce the range.
●Weak batteries will reduce range. Replace every 12 –18 months. In cold conditions (below 5ºC),
batteries may need to be replaced more often.
Push does not work with my older Libra equipment …
●Libra + is not compatible with the earlier Libra system.
●Only use accessories marked Libra +.
Troubleshooting

5
Specifications
Specification Bell push
Operating Temperature -10 to 40ºC
RF Frequency – UK/Europe 868MHz
RF Power <10mW
Battery Type CR2032
Battery Life (5 activations/day) 18 months
IP Rating IP55
Friedland guarantees this product for 2 years
from the date of purchase. Proof of purchase
is required; this does not affect your statutory
rights. If you require further information about
your product, call the Friedland helpline on
01268 563066.
Guarantee
Batteries and waste electrical products should
not be disposed of with household waste.
Please recycle where these facilities exist.
Check with your local authority or retailer for
recycling advice.
Disposal & Recycling
Novar ED&S hereby declares that this product
is in compliance with the essential requirements
and other relevant provisions of the Radio and
Telecommunications Terminal Equipment
(R&TTE) directive, 1999/5/EC.
Declaration
Friedland, The Arnold Centre, Paycocke Road, Basildon, Essex, SS14 3EA
www.friedland.co.uk