FROST 06.1050 User manual

FC Frost Limited
Bankside Works Benfield Way
Braintree Essex CM7 3YS
United Kingdom
T: [phone]
F: [phone]
E: [email protected]
W: www.fcfrost.com
Automatic Soap Dispenser
06.1050
FC Frost Ltd reserves the right to amend the design or dimensions without formal notice. © FC Frost Ltd 2016
Specification
Wall/Bulkhead mounted automatic liquid soap dispenser with touchless operation. Model number 06.1050
with cylindrical body in polished chrome and 1.5 litre poly bottle. Infra-red sensor operated with range
between 0-80mm. AC 230V, 50Hz or 4x1.5V DC
Material
Body: Polished chrome plated brass
Stem: Brass
Bottle: White plastic
Trunking PVC-U
Operation
Place hand under spout to dispense liquid soap into palm of hand. Each activation delivers approximately
2ml of liquid soap (On maximum setting 4. See Diagram 3). Recommended for high traffic use areas.
Liquid Soap
Soap viscosity 100-3500cp
FC Frost Ltd recommends using Frost ‘Pearlised’ liquid soap (Product code 06.8305). We do not
recommend using high viscosity liquid soaps or gels, which may impair function. Warning: Liquid soap with
high sodium chloride content can cause corrosion and may invalidate the product warranty.
Installation Positioning Guidelines
Access requirements: Pumps and transformers must be accessible at all times for servicing
Do not install on reflective surfaces or opposite mirrors
Do not install opposite other sensor taps or soap dispensers
To avoid interference from other power demands, install on its own power circuit
Bottle Refilling
Hold bottle firmly
Press button located on right hand side of grey housing above bottle
Bottle will detach automatically
Refit bottle by sliding bottle over dip tube and pushing neck into the underside of the housing. A
“Click” is heard upon secure engagement of bottle

FC Frost Limited
Bankside Works Benfield Way
Braintree Essex CM7 3YS
United Kingdom
T: [phone]
F: [phone]
E: [email protected]
W: www.fcfrost.com
Automatic Soap Dispenser
06.1050
FC Frost Ltd reserves the right to amend the design or dimensions without formal notice. © FC Frost Ltd 2016
Mounting: See Diagram 1 opposite
Prepare a Ø26mm mounting hole through wall
Loosen Grub Screw (4) from Body (1) and
remove Stem (3) and Bracket (5) over Cables (6)
Ensure Escutcheon (2) is fitted over Body
Pass cables (6) through front of hole in wall
Re-fit Stem (3) and Bracket (5) over cables
Insert Stem (3) into hole in wall, from rear
Fix Stem (3) in position by screwing Bracket (5)
to back of wall using suitable fixings.
Push Body (1) over Stem (3) until soap
dispenser is firmly clamping the wall
The Body (1) and Escutcheon (2) should now be
clamping the wall with shoulder of Stem (3) and
Bracket (5) on the opposite side
Ensure the Body (1) is aligned with spout facing
downwards and tighten Grub Screw (4)
The soap dispenser should now be fixed
securely to the wall.
Diagram 1
Trunking Installation: See Diagram 2 below.
Trunking supplied
Diagram 2
Soap dispensing quantity settings: Diagram 3
Gears located under black rubber cap:
Gear 1 is the lowest setting with the switches set to
the right hand side.
Gear 2 top switch to the left hand side, bottom switch
to the right hand side
Gear 3 top switch to the right hand side, bottom
switch to the left hand side
Gear 4 is the highest setting with the switches set to
the left hand side
Fill the soap bottle before operating the soap
dispenser for the first time
Press and hold down the purge button (next
to settings) until soap is dispensed from the
spout of the dispenser
Place hand under spout to activate sensor

FC Frost Limited
Bankside Works Benfield Way
Braintree Essex CM7 3YS
United Kingdom
T: [phone]
F: [phone]
E: [email protected]
W: www.fcfrost.com
Automatic Soap Dispenser
06.1050
FC Frost Ltd reserves the right to amend the design or dimensions without formal notice. © FC Frost Ltd 2016
Mains Installation AC Operation
Installation and repairs must be carried out by a
qualified electrician in accordance to local
electrical regulations.
Assemble soap dispenser as shown in illustration
Battery pack also acts as back up to mains supply
and may be installed to power adaptor male
connector if desired.
Battery Installation DC Operation
Open battery compartment top cover using crosshead screwdriver.
Install 4 Alkaline Type AA 1.5V batteries ensuring that they are
installed correctly (Match the +/+ indications between battery
and connections) Arrows must align on battery pack lid and
container. Failure to do so may damage the unit.
Replace batteries when red light in sensor window blinks
Approx life. 50,000 operations using high quality battery.

FC Frost Limited
Bankside Works Benfield Way
Braintree Essex CM7 3YS
United Kingdom
T: [phone]
F: [phone]
E: [email protected]
W: www.fcfrost.com
Automatic Soap Dispenser
06.1050
FC Frost Ltd reserves the right to amend the design or dimensions without formal notice. © FC Frost Ltd 2016
Spares
Contact FC Frost for spares requirements: [e-mail]
Care and Maintenance
Water marks and soap residue on polished chrome surfaces are best cleaned using a damp soft cloth a mild
detergent. Never use an abrasive cloth to remove stubborn stains. Dry with a soft clean cloth.
Periodically flush soap dispenser through with warm water to prevent soap from clogging.
Prevent dust build up on bottle, by dusting regularly. Any dust inside the container may result in tube
blockages. Ensure soap inside the bottle is uncontaminated at all times.
Low level amounts of soap may solidify, Top up bottle with soap regularly.
Do not place soap dispenser into water, as this is likely to damage the circuit board.
Clean battery box with a dry towel only.
Warranty
This product is covered by a 12-month warranty from the date of purchase to be free from defects if installed
and maintained in accordance with these instructions. FC Frost will replace or repair (as appropriate) free of
charge any product with a proven manufacturing defect if reported within the warranty period.
Product has been tested to 200,000 operations.
This product falls within the scope of the Waste Electrical & Electronic Equipment Regulations Directive (WEEE)
This product should not be disposed of with household waste. Please recycle where facilities exist or contact FC Frost Ltd for
further assistance. Check with your local authority for further recycling advice.
Batteries should be disposed in accordance with Waste Batteries and Accumulators Regulations or local authority regulations