FROST N1978 Installation guide

SOAP & DISINFECTANT
TOUCH FREE DISPENSER
. . .
PRODUCT DETAILS, TECHNICAL DETAILS
AND MOUNTING INSTRUCTIONS
The FROST Soap & Disinfectant Touch Free Dispenser consists of a touch free dispenser
and additional table and floor dispenser stands. The refillable container holds 500 ml (17 oz) liquid soap or
hand disinfection gel, equivalent to approx. 600 doses. The dosage is released once when
your hand is held 5-15 cm (2-6 in) below the dosage nozzle.
By choice, the dispenser is either wall mounted or easily fixed to the table
or floor dispenser stands.
The FROST Soap & Disinfectant Touch Free Dispenser combines hygiene with aesthetics
and offers an elegant minimalistic design solution for the modern interior space.
The design compliments all FROST products.
The dispenser is available in all nine FROST finishes.
The stands are available in Matt Black or Matt White.
The FROST Soap & Disinfectant Touch Free Dispenser is part of
the NOVA2 series designed by Bønnelycke mdd.
www.frost.dk

2WWW.FROST.DK
SOAP & DISINFECTANT
DISPENSER
touch free, with lock, 500 ml
f/ wall or dispenser stands
Stainless Steel
Height: 217 mm
Diameter: Ø89 mm
Projection: 112 mm
CC: 114 mm
Brushed
Stainless
N1978
Brushed
Copper
N1978-BOC
Brushed
Gold
N1978-BMG
Brushed
Black
N1978-BCB
Polished
Stainless
O1978
Polished
Copper
N1978-C
Polished
Gold
N1978-GO
Matt
Black
N1978-B
Matt
White
N1978-W
TABLE DISPENSER STAND
for Soap & Disinfectant Dispenser
Stainless Steel
Height: 500 mm
Diameter: Ø32 / Ø180 mm
Projection: 180 mm
Matt Black
N1978-1-B
Matt White
N1978-1-W
Brushed Stainless
N1978-1
FLOOR DISPENSER STAND
for Soap & Disinfectant Dispenser
Stainless Steel
Height: 1200 mm
Diameter: Ø32 / Ø250 mm
Projection: 250 mm
Matt Black
N1978-2-B
Matt White
N1978-2-W
Brushed Stainless
N1978-2

CC 114 mm
217 mm
500 mm
1200 mm
Ø89 mm
Ø180 mm
Ø250 mm
112 mm
3WWW.FROST.DK
DIMENSIONS AND DETAILS
Applicable power supply: DC9V (AA x 6)
Refill container capacity: Approx. 500 ml (17 oz) (approx. 600 doses)
Metered dose: 0.8 ml-6.5 ml (adjustable)
Ambient temperature: 0.1-45 °C
Sensing distance: 5-15 cm (2-6 in)
The dispenser is made from stainless steel AISI 304.
The dispenser stands are made from stainless steel AISI 304.
NOTE: The dispenser stands are sold separately.

Solid stainless steel base
M10 countersunk stainless steel hex key bolt
Stainless steel tube
Plastic connectors
4WWW.FROST.DK
MOUNTING INSTRUCTIONS
By choice, the dispenser is either wall mounted or fixed to the additional dispenser stands.
The stands are easily assembled with the included mounting accessories and the dispenser
is as easily fixed to the stands.
Before mounting, please read instructions on the following pages.
NOTE: Do not mount the dispenser in the shower.

min. 25 cm
Lock Unlock
5WWW.FROST.DK
Choose the placement for the dispenser.
The bottom of the dispenser must be mounted at least 25 cm from the nearest reflector or
tabletop.
NOTE: Do not mount the dispenser in direct sunlight, be aware of reflective surfaces below
the sensor and do not mount the dispenser in the shower.
STEP 1: Mounting The Dispenser
Use the enclosed Hex Key to unlock the dispenser lid.
Whether you choose to mount the dispenser on a wall or fix it to the additional dispenser
stands, please see page 3 and 4 for the main measurements and mounting instructions.
NOTE: Please use the two enclosed plastic connectors to mount the dispenser on the
dispenser stands.
When the lid is removed simply fill the container with liquid soap or disinfection gel.
NOTE: Always use liquid with low viscosity, hence do not to use shampoo, conditioner
or shower gel etc. Feel free to use the enclosed soap and disinfection gel stickers on for
instance, the dispenser lid.
STEP 2: (re)Filling Liquid Container
1
1
2
2

LED
protective sticker
6WWW.FROST.DK
Press the Battery Release in and upwards to pull out the Battery Box.
STEP 3: Insert / Change Batteries
Slide the Battery Box back in and gently press down the Battery Release.
Place the dispenser lid back on and lock it with the enclosed Hex Key.
Insert (replace) the six AA batteries in the Battery Box.
NOTE: To ensure a long service life, always use high quality AA batteries, make sure all six
batteries are from the same brand and never mix used batteries with new ones.
On the bottom of the dispenser the LED will flash 5 times and enter Normal Operation Mode.
NOTE: The LED will automatically start flashing when the batteries needs to be replaced.
Remove the protective sticker from the Sensor and the dispenser is ready for use without
any further settings.
1
3
2
4
5

press and hold for 15 sec.
press and hold for 5 sec.
LED
sensor
sensor
5-15 cm (2-6 in)
LED
7WWW.FROST.DK
STEP 4: Proximity Sensor Setting
Place the palm of your hand below the Sensor within the required sensing distance from
the dispenser bottom and hold while the LED flashes.
NOTE: The sensing distance must be between 5-15 cm (2-6 in).
To enter the Proximity Sensor Mode press and hold the Settings Button for 5 seconds
and release when the LED starts flashing.
When the LED flashes stops, the Proximity Sensor Setting is complete.
When the protective sticker from the Sensor has been removed, press and hold
the Setttings Button for 15 seconds to enter the System Setting Mode.
1
3
2
4

press twice
press and hold for 15 sec.
sensor
8WWW.FROST.DK
Press the Settings Button twice to enter the Liquid Output Settings.
Take notice of where the Sensor is located.
STEP 5: Liquid Output Settings
When the LED flashes place the palm of your hand below the Sensor to activate it.
Remove your hand when you reach the metered dose of your request.
NOTE: The metered dose must be between 0,8 - 6,5 ml.
Press and hold the Settings Button for 15 seconds to enter the System Setting Mode.
1
3
2
When the LED flashes stops, the Liquid Output Setting is complete.
4
LED

press five times
press and hold for 2 sec.
LED
9WWW.FROST.DK
When the LED stops the dispenser has entered Sleep Mode.
STEP 6: Sleep Mode Settings (during cleaning / maintenance)
Press and hold the Settings Button for 2 seconds for the dispenser to return to Normal
Operation Mode.
For other languages, DE, NL, FR, SE and DK
please see our website www.frost.dk
Press the Settings Button five times to avoid accidental operation during cleaning
or maintenance.
1
3
2

10WWW.FROST.DK
Situation
LED light is not on
LED light is normal but no liquid output
Insufficient liquid output
Treatment
Please check the circuit or batteries
Adjust the proximity sensor settings
Replace the batteries
Clean the sensor
Remove possible obstacles from the sensor
Adjust the proximity sensor settings
Please inform the dealer
Adjust the liquid output settings
Please change into low viscosity liquid
Please use it several times continuously until
the liquid can be ejected normally
Reason
Abnormal power supply
Sensing distance is too short
Poor battery contact or out of battery
Sensor dirty
Sensor continuously sensing
Sensing distance is not as recommended
Machine stoppage
Induction time is too short
The liquid is too viscous
Liquid solidification or blockage
Simple Trouble Shooting