FrSky XJT Lite User manual

Instruction Manual for FrSky XJT Lite Module
Specifications
● Dimension: 62.4mm × 30mm×14.5mm (L×W×H)
● Weight: 20g
● Channel: 16CH
● Operating Voltage Range: DC 6.5V~8.4V
● Operating Current: [email protected] Typ
● Upgrade Interface: Smart Port
Introduction
FrSky XJT Lite module is a 2.4GHz frequency system which is especially designed for FrSky Taranis series
transmitter like X Lite S/Pro and X9 Lite. In addition, it gets low latency and high precision thanks to the upgraded
digital interface and high-speed data transmission. This being the “Lite” version works perfectly with all FrSky
receivers in the ACCST D16(Non-LBT), D8, LR12.
Features
● High-speed digital module interface
● Telemetry data transmission supported
Binding Procedure
Binding is the process of uniquely associating a particular receiver to a transmitter module. A transmitter module can
be bound to multiple receivers (not to be used simultaneously). A receiver can only be bound to one transmitter
module. Follow the steps below to finish the binding procedure.
1.
For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2, choose
External RF-Mode XJT Lite D16 or D8/LR12. then select [Bnd].
2.
Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED on the receiver
will flash, indicating the binding process is completed (please refer to the corresponding receiver
’ s instruction
manual for details).
3.
Turn off both the transmitter the receiver.
4.
Turn on the transmitter and connect the battery to the receiver. The GREEN LED on the receiver indicates the
receiver is receiving commands from the transmitter. The receiver/transmitter module binding will not have to be
repeated, unless on of the two is replaced.
Mode of XJT Lite
D8
D16 (Non-LBT)
LR12
Compatible Receiver
V8-II series receivers (V8FR-II,V8R7-II,V84R-II,VD5M,etc.)
D series receiver (D8R-II plus,D8R-XP,D6FR,D4R-II,etc.)
X series non-LBT rceiver(X8R,X4R,etc.)
L series receiver (L9R,etc.)
Green LED
Flashing
Flashing
ON
RED LED
ON
OFF
Flashing
Status
Normal
Range Check
Binding
Overview
30
62.4
14.5
41.9
9.8
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]

Instruction Manual for FrSky XJT Lite Module
FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals.
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Note: After binding procedure is completed, recycle the power and check if the receiver is really
under control by linked transmitter.
Note: XJT Lite complys with FCC certification requirements, only FCC (Non-LBT)version, please
comply with local laws and regulations when using.
Range Check
A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete
buildings or trees can cause loss of signal during range check and flight. Under Range Check mode, RF power will
decrease and Range distance will reduce to 1/30-1/10 that of Normal model.
1. Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench). The
receiver antenna should be in vertical position.
2. Turn on the transmitter and the receiver, go to MODEL SETUP—External RF—Mode XJT Lite—Range.