FSR FLH20-0-BX User manual

FSR 244 Bergen Boulevard, West Paterson, NJ 07424, Phone: [phone] - Fax: [phone]
43134 LIT1235
C-1059
FLH20-0-BX/FLH20-0S-C Installation Guide
BOX INSTALLATION - STEP 1
REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.
LOCATE AND POSITION BOX IN ACCORDANCE WITH
FLOOR PLANS. TOP EDGE OF BOX MUST BE FLUSH WITH
CONCRETE POUR. LEVEL AND ANCHOR BOX AS REQUIRED.
USE SCREWS, NAILS, OR WIRE TO PREVENT BOX FROM
FLOATING DURING POUR. ROUTE CONDUITS TO BOX AS
REQUIRED. PLACE THIS INSTALLATION GUIDE BACK INTO
BOX, ALONG WITH ALL SUPPLIED ITEMS, AND REINSTALL
TEMPORARY COVER.
TEMPORARY COVER
(4) #8-32 FLAT HEAD SCREW
TOP EDGE TO
BE FLUSH WITH
CONCRETE
BOX INSTALLATION - STEP 2
SCREED TO TOP OF BOX SURFACE. HAND TROWELING
RECOMMENDED NEAR BOX EDGES. BOX HAS NO
HEIGHT ADJUSTMENT AFTER CONCRETE POUR.
GANG MOUNTING BRACKET
REMOVABLE LARGE CENTER DIVIDER
REMOVABLE SMALL
CENTER DIVIDER
(10) #8-32 PAN HEAD SCREW
CENTER DIVIDER CONFIGURATION
SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.
REMOVABLE SMALL
CENTER DIVIDER
GANG MOUNTING BRACKET
REMOVABLE LARGE CENTER DIVIDER
INSTALL BOX-ATTACHED CHAIN TO COVER, AND REPLACE COVER
BACK INTO NEWLY-INSTALLED RIM, LATCHING THE SMALL DOORS
IN PLACE (REVERSE ACTIONS OF DETAILS 1 THRU 3 PREVIOUSLY
DONE). CHAIN FROM BOX CAN BE REMOVED AND INSTALLED TO
ALTERNATE LOCATION, IF DESIRED.
COVER INSTALLATION
STUD FOR ALTERNATE
LOCATION OF CHAIN
BRACKET FOR STORING
SMALL DOOR WHEN
REMOVED FROM COVER
COVER
CONCRETE SURFACE
FSR Inc.
244 Bergen Boulevard, West Paterson, NJ 07424
Phone: [phone] - Fax: [phone]
Web: www.fsrinc.com - E-mail: [email protected]om
CONCRETE SURFACE
#8-32 PAN HEAD SCREW
CHAIN FROM BOX

1-GANG/2-GANG CONFIGURATION
(2-GANG/1-GANG ALSO POSSIBLE) 2-GANG/2-GANG CONFIGURATION
3-GANG/1-GANG CONFIGURATION
(1-GANG/3-GANG ALSO POSSIBLE) 4-GANG CONFIGURATION
IF INSTALLING "JUNCTION BOX/ABANDONMENT" COVER, USE
THAT COVER'S INSTALLATION GUIDE, AND IGNORE THE REMAINDER
OF THESE INSTALLATION INSTRUCTIONS.
NOTE
GANG MOUNTING BRACKET
(2) DIVIDER HOLDER
OPTIONAL
DIVIDER
COVER
PLATE GANG MOUNTING
BRACKET
DIVIDER
HOLDER
OPTIONAL
DIVIDER
GANG MOUNTING
BRACKET
DIVIDER
HOLDER
OPTIONAL
DIVIDER GANG MOUNTING
BRACKET
(2) DIVIDER HOLDER
(NO DIVIDERS USED!)
GANG DIVIDER ASSEMBLY
87.5
cu. in. 94
cu. in. 87.5
cu. in. 94
cu. in.
117.5
cu. in. 64
cu. in. 183.3
cu. in.
CUTAWAY FOR
CLARITY ONLY
DIVIDER HOLDER:
INSTALL WITH #8-32
FLAT HEAD SCREW
TO GANG MOUNTING
BRACKET
OPTIONAL
DIVIDER
COVER PLATE:
INSTALL WITH #6-32
PAN HEAD SCREW TO
GANG MOUNTING
BRACKET
INSTALLED
ELECTRONIC
COMPONENT
GANG
MOUNTING
BRACKET
INSTALLING ELECTRONIC COMPONENTS
PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
PLACE THIS INSTALLATION GUIDE BACK IN BOX AND REINSTALL
TEMPORARY COVER IF FINISHED COVER IS TO BE INSTALLED AT
A LATER DATE.
COVER RIM INSTALLATION
REMOVE AND DISCARD TEMPORARY COVER AND SCREWS.
REMOVE COVER ASSEMBLY FROM RIM (SEE DETAILS 1 THRU 3),
SET REMOVED COVER (WITHSMALL DOORS) ASIDE. APPLY A
CONTINUOUS 1/4" BEAD OF RTV SILICONE TO THE INSIDE CORNER
OF ALL 4 SIDES OF THE CONCRETE-STOP FLANGE ON THE BOX
(SEE RTV SILICONE PLACEMENT DETAIL). QUICKLY INSTALL RIM
ONTO BOX WITH PROVIDED (8) #8-32 x 1/4" FLAT HEAD PHILLIPS
SCREWS AND (2) #8-32x 5/16" FILLISTERHEAD SCREWS. RIM
COVER ASSEMBLY
DETAIL 1
LIFT LATCH HANDLE 90° DETAIL 2
ROTATING LATCH HANDLE 45° CLOCKWISE
ALLOWS COVER TO BE REMOVED FROM RIM
DETAIL 3
ROTATING LATCH HANDLE 90° CLOCKWISE
ALLOWS SMALL DOOR TO BE REMOVED
FROM COVER
APPLY A CONTINUOUS 1/4" BEAD
OF RTV SILICONE TO ALL 4 SIDES
(8) #8-32 FLAT HEAD SCREW
RIM
CONTINUOUS
1/4" BEAD OF
RTV SILICONE
PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND
REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).
GANG MOUNTING BRACKET CONFIGURATION
LATCH OPERATION
CONCRETE FLOOR
RTV SILICONE PLACEMENT DETAIL
(2) #8-32 PAN HEAD
SCREW
#8-32 FILLISTER
HEAD SCREW
#8-32 FILLISTER
HEAD SCREW