FujiFilm FCR CAPSULA X User manual

All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by means,
electronic, mechanical, photocopying, recording or otherwise, with-
out the prior written permission of Fuji Photo Film Co., Ltd. Miyano-
dai Technology Development Center.
FCR ® is a registered trademark of Fuji Photo Film Co., Ltd.
<No part of this manual may be reproduced or transmitted.>
Copyright © 2005 by Fuji Photo Film Co., Ltd.
The relationship between mR (milliroentgen), which is the
unit of radiation, and μC/kg (micro-coulomb/kilogram),
which is the SI derived unit of radiation, is as follows.
1 mR = 0.258μC/kg
FUJI COMPUTED RADIOGRAPHY
Fuji Photo Film Co., Ltd.
Printed in Japan
Service Manual
FCR CAPSULA X/FCR CARBON X
CR-IR 357
Capsula-E(CR-IR 357)
E-Only
Document No. 014-204-01A
1st Edition - Aug. 15, 2005
Revised Edition - Nov. 10, 2005

BLANK PAGE

CR-IR 357 Service Manual
0.1
0.1
Capsula-E(CR-IR 357)
E-Only
014-204-01E
11.10.2005 FM4750
1.3 About Notation in the Manual
 Notation of cautions, warnings, etc.
The notation formats of "warning", "caution", "Instruction", "note", and "reference" are shown
below.
WARNING
Used when death or serious injury may occur if the instruction is not observed.
CAUTION
Used when minor or medium levels of physical injury may be incurred if the instruction
is not observed.
Also used when the machine may suffer serious trouble (such as unrecoverable or
difficult-to-recover trouble).
 INSTRUCTION 
Used when the machine may suffer damage, or any failure or malfunction may occur, if the
instruction is not observed.
 NOTE 
Used to indicate the matters that need attention during steps of the procedure.
REFERENCE
Used to indicate terminology or supplemental explanations.
 Indication of Refer To
The " " mark is used to indicate the chapter or section you should refer to.
Its format is as indicated below.
{MC:5.1_Cassette Set Unit}
 Notation in the Manual
In this Service Manual, the CR-IR 357 is sometimes denoted simply as the RU (Reader Unit),
and the CR-IR346/348CL as the CR Console.
1. Handling of This Manual
1.1 About This Manual
 Scope
This Service Manual is applicable to Fuji Computed Radiography CR-IR 357. The machine is
categorized as Class 1 according to IEC classification.
 Notation of Unit Symbols
For notation of unit symbols, metric units set forth in the International Systems of Units (SI) are
used, as a rule. However, metric units that are allowed in the Measurement Law, not in the SI,
are used in some cases.
1.2 Precautions for Handling of This Manual
1. Fuji Photo Film Co., Ltd reserves all rights related to this manual.
2. This manual should be accessible only to technical service personnel
authorized by Fuji Photo Film Co., Ltd.
3. Since this manual contains confidential information of Fuji Photo Film Co.,
Ltd, such as the internal structure of the product, appropriate measures
should be taken to prevent illegal or inappropriate disclosure and/or use of
this manual.
4. The following conducts are prohibited without prior written approval of Fuji
Photo Film Co., Ltd.:
- Copy or transcribe a whole or part of the contents of this manual
- Disclose, furnish, lend, and/or transfer a whole or part of the contents of
this manual to persons other than the afore-described technical service
personnel.
- Use a whole or part of the contents of this manual for purposes other than
technical servicing of the product.
5. Portions of the descriptions in this manual may be revised due to
improvements on the product.

CR-IR 357 Service Manual
0.2
0.2
Capsula-E(CR-IR 357)
E-Only
014-204-01E
11.10.2005 FM4750
 Notation of Symbols
- Check/Adjustment indicator: Indicates that it is necessary to check or adjust the
installation location when the part or component
removed is to be reinstalled.
This indicator is placed in the illustration that depicts
the procedures for removing the parts and components.
When you see this indicator, refer to its relevant
" Check/Adjustment Procedures."
- Half-punch indicator: Indicates that it is necessary to align the half-punches
when installing the parts or components.
However, it is not indicated for the half-punches for
improving ease of assembly or preventing erroneous
assembly procedures.
 Servicing Instruments and Tools That Require Inspection/Calibration
The machine should be installed and serviced by use of servicing instruments and tools that
have been inspected and calibrated as appropriate.
If the machine were serviced using servicing instruments and tools that have not been inspected
and calibrated, proper performance of the machine could not be guaranteed.
Servicing instruments and tools that require inspection/calibration are as listed below.
Inspection/calibration procedures should be performed in accordance with the inspection/
calibration manuals described in the ECN Information.
 Instruments and tools that require inspection/calibration
Name Inspection Calibration Servicing instrument inspection/
calibration manual No.
Dosimeter - FF-001
Steel rule (150mm) -FF-005
Steel rule (300mm) -FF-006
Digital tester   FF-012
Calipers  (✽)-FF-015
✽: A block gauge for use in inspection requires calibration.
CHECK1