FujiFilm FDR ES DR-ID1270 User manual

897N120821E
This Operation Manual describes details on how to operate the DR-ID1270 and
cautions to be observed when operating it.
After reading this manual, store it nearby the DR-ID1270 so that you can see it
whenever necessary.
(DR-ID1270)
Operation Manual
6th Edition : July 2018
For Safe Operation
System
Conguration
(Product Overview)
Basic Operation
Daily Inspection and
Maintenance
Appendix
Maintenance and
Inspection

ii DR-ID1270 Operation Manual 897N120821E

iii
DR-ID1270 Operation Manual 897N120821E
Introduction
DR-ID1270 is an X-ray equipment which acquires a general radiograph from the indirect-conversion
at panel sensor.
Indications for use (for U.S.)
The Wired/Wireless FDR ES (DR-ID1270) at panel sensor system is intended to capture for display
radiographic images of human anatomy. It is intended for use in general projection radiographic
applications including pediatric and neonatal exams wherever conventional lm/screen or CR systems
may be used. It is not intended for mammography, uoroscopy, tomography, and angiography
applications.
Intended Use (for European Union and other countries.)
The Fujilm DR-ID1270 provides digital image capture for radiographic examinations. It is intended for
use in general projection radiographic applications wherever conventional screen-lm systems or CR
systems may be used. DR-ID1270 is a device that provides images, which diagnostic image process
is not implemented, to image collecting console. It is not designed for mammography, uoroscope,
tomography or angiography.
Note : The above statements were determined by applicable medical device regulations which vary
throughout the world. These statements are subject to revision when additional clearance or
approval is obtained.
DR-ID1270 consists of at panel sensors (DR-ID1271SE/DR-ID1272SE/DR-ID1273SE/DR-ID1274SE/
DR-ID1275SE), software for the control cabinet.
DR-ID1271SE, DR-ID1272E, DR-ID1273SE, DR-ID1274SE and DR-ID1275SE :
Wireless communication mode or wired communication mode is available. When used in wireless
communication mode, an access point and battery pack (optional) are required.
Each at panel sensor complies with IEC 62220-1 (MEDICAL ELECTRICAL EQUIPMENT -
CHARACTERISTICS OF DIGITAL X-RAY IMAGING DEVICES - ) as a general X-ray radiography
equipment.
The detector of at panel sensors features 150 micron pixel pitch, a wide 16-bit dynamic range and
exposure times up to 3.8 seconds.
This Operation Manual includes descriptions of matters necessary when using the DR-ID1270
such as the equipment overview, operation procedures and precautions to observe, as well as daily
inspections and maintenance.
Accompanying documents were originally drafted in the English language.
Installation may only be conducted by authorized service personnel.

iv DR-ID1270 Operation Manual 897N120821E
CAUTIONS
1. No part or all of this manual may be reproduced in any form without prior permission.
2. The information contained in this manual may be subject to change without prior notice.
3. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
installation, relocation, remodeling, maintenance, and repair performed by other than dealers
specied by FUJIFILM Corporation.
4. FUJIFILM Corporation shall not be liable for malfunctions and damages of FUJIFILM
Corporation products due to products of other manufacturers not supplied by FUJIFILM
Corporation.
5. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
remodeling, maintenance, and repair using repair parts other than those specied by
FUJIFILM Corporation.
6. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
negligence of precautions and operating methods contained in this manual.
7. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from use
under environment conditions outside the range of using conditions for this product such as
power supply, installation environment, etc. contained in this manual.
8. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
natural disasters such as res, earthquakes, oods, lightning, etc.
This system is classied as a medical device under EC Directive 93/42/EEC.
Process waste correctly, as stipulated by local law or any regulations that apply.
Caution : Rx Only in the United States (Federal law restricts this device to sale by or on the order
of a physician.)
Open-Source Software Contained in This Product
This product contains third party’s software that is made available as open source software or free
software.
This software is provided “as is” with no warranty of any kind as to its merchantability or tness for any
particular purpose.
For the information on open source software contained in this product, please see the attached DVD.
Source codes for certain type of open source software used in this product are available at delivery cost.
If you would like to receive such source codes, please contact FUJIFILM dealer or the service
representatives at the agency from which you purchased this product. (Please be noted that any
inquiries concerning the contents of source codes should be directed to original licensors of open source
software.)
Note : FUJIFILM has successfully performed verication and validation testing on all third party
software and has conrmed its suitability to be used in this system.
Trademarks
All company names and product names described in this manual are the trademarks or registered
trademarks of FUJIFILM Corporation or their respective holders.
Windows is the registered trademark of US Microsoft Corporation in the U.S.A. and other countries.
Copyright © 2015-2018 FUJIFILM Corporation. All rights reserved.

v
DR-ID1270 Operation Manual 897N120821E
Contents
Introduction...........................................................................................................................iii
Chapter 1 For Safe Operation
1.1 Safety ...................................................................................................................... 1-1
1.2 Electromagnetic Compatibility (EMC).................................................................... 1-11
1.2.1 DR-ID1270............................................................................................................. 1-11
1.3 Precautions in Using the DR-ID1270 ................................................................... 1-16
1.3.1 Handling.................................................................................................................1-16
1.3.2 Before Exposure....................................................................................................1-18
1.3.3 During Exposure....................................................................................................1-18
1.3.4 During Cleaning.....................................................................................................1-19
1.3.5 Storage ..................................................................................................................1-19
1.3.6 Precautions Related to the Load Applied to the Flat Panel Sensor.......................1-20
1.3.7 Radio Waves .........................................................................................................1-21
Chapter 2 System Conguration (Product Overview)
2.1 DR-ID1270 .............................................................................................................. 2-1
2.1.1 System Conguration ..............................................................................................2-1
2.1.2 Features of the DR-ID1270......................................................................................2-2
2.2 Unit Names and the Functions................................................................................ 2-3
2.3 Locations of Labels and Signs ................................................................................ 2-5
2.3.1 Locations of Labels..................................................................................................2-5
2.3.2 Safety and Other Symbols.......................................................................................2-8
2.3.3 Symboles de sécurité et autres ...............................................................................2-9
2.4 Installation Conditions ........................................................................................... 2-10
2.4.1 Denition of Patient Environment ..........................................................................2-10
2.4.2 Installation Precautions.......................................................................................... 2-11
2.4.3 Precautions for Installing the Access Point (Optional)........................................... 2-11
2.5 Wireless Specications ......................................................................................... 2-12
Chapter 3 Basic Operation
3.1 Preparing the Flat Panel Sensor ............................................................................. 3-1
3.1.1 Type of Flat Panel Sensor .......................................................................................3-1
3.1.2 Number of the Connectable Flat Panel Sensors .....................................................3-1
3.1.3 Connecting/Disconnecting the Flat Panel Sensor Connector..................................3-1
3.1.4 Inserting/Removing the Flat Panel Sensor into/
from the Radiographic Examination Stand ..............................................................3-2
3.1.5 Changing the Direction of the Flat Panel Sensor Connector...................................3-4
3.1.6 Charging the Battery Pack for the Flat Panel Sensor..............................................3-5
3.1.7 Installing/Removing the Battery Pack for the Flat Panel Sensor .............................3-6
3.2 Starting Up and Shutting Down the System................................................................3-8
3.2.1 Starting Up the System............................................................................................3-8
3.2.2 Shutting Down the System ......................................................................................3-9
3.3 Sleep mode ........................................................................................................... 3-11
Chapter 4 Daily Inspection and Maintenance
4.1 Daily User Inspection and Maintenance......................................................................4-1
4.1.1 Periodical Inspection................................................................................................4-1

vi DR-ID1270 Operation Manual 897N120821E
Appendix A Specications
A.1 Specications ..........................................................................................................A-1
A.1.1 Reduced Equivalent (DR-ID1270) .......................................................................... A-1
A.1.2 Power Supply Conditions........................................................................................ A-1
A.1.3 Environmental Conditions....................................................................................... A-1
A.1.4 Image Performance ................................................................................................ A-2
A.1.5 Load Restriction...................................................................................................... A-2
A.1.6 Radio Waves .......................................................................................................... A-2
A.2 External View and Weight .......................................................................................A-3
A.2.1 DR-ID1270.............................................................................................................. A-3
A.3 Characteristics.........................................................................................................A-6
Appendix Z Precautions for Exposure
Z.1 Precautions for the Automatic X-ray Detection Function.............................................Z-1
Z.1.1 Precautions for Making an Exposure.......................................................................Z-1
Z.1.2 Precautions Related to the X-ray Exposure Time....................................................Z-2
Z.2 Other Precautions ...................................................................................................Z-3
Z.2.1 Precautions for Exposure of a Subject in Relatively Large Contrast .......................Z-3
Z.2.2 Precautions for Flat Panel Sensor...........................................................................Z-3
Z.2.3 Precautions for Assuring the Radiation Field...........................................................Z-3
Z.2.4 Images Output When the X-ray Shot Switch is Operated Incorrectly......................Z-3
Z.2.5 Precautions for Urgent Use .....................................................................................Z-4
Z.2.6 Precautions Related to Continuous Operation ........................................................Z-4
Z.2.7 Precautions Related to Grid.....................................................................................Z-4
Z.2.8 Precautions during Calibration.................................................................................Z-4
Z.2.9 Precautions for Exposing the Flat Panel Sensor to X-ray........................................Z-4
Z.2.10 Precautions for Extended Image Readout...............................................................Z-4
Z.2.11 Precautions for Using the Access Point ..................................................................Z-5
Appendix O Use of Optional Items
O.1 Optional Items ....................................................................................................... O-1
O.2 Using the SE Storage Case ................................................................................... O-2
O.3 Power Supply Unit.................................................................................................. O-3
O.4 Power Box.............................................................................................................. O-3
O.5 Access Point........................................................................................................... O-4
Maintenance and Inspection

1-1
For Safe Operation
1
DR-ID1270 Operation Manual 897N120821E
Chapter 1 For Safe Operation
1.1 Safety
Before using the DR-ID1270, read this section thoroughly to ensure that you use the product properly.
Electric Shock Warnings and Cautions
WARNING
This product is internal power supply equipment.
To avoid electric shocks, users should always take the following precautions:
● Do not open any covers when it is not necessary.
● Install the equipment in a location where it will not be exposed to water.
WARNING
Do not touch the patient’s body while touching the control cabinet and the image processing
unit. Otherwise, the patient may receive an electric shock.
WARNING
Do not use a multiple tap connector or extension cable for powering the devices constituting
the system. Otherwise, re or electric shock may occur due to the electrical load exceeding the
allowable limit.
WARNING
Observe the following precautions when using the cables.
● Do not touch the plug and connector with wet hands. Otherwise, electric shock may result,
causing death or severe injury.
● Hold the plug or connector when removing the cable.
Pulling the cable or carrying by holding it may damage the cable, causing re or electric shock.
● Do not damage or remodel the cable.
Do not place a heavy object on the cable or lay it under the at panel sensor. Do not step on,
pull, forcibly bend, or bundle the cable. Otherwise, re or electric shock may result.
● Do not use the at panel sensor for the radiographic examination stand if its cable becomes
overloaded. Otherwise, the cable may be damaged, causing re or electric shock.
WARNING
Do not turn on the system with dew condensation on the at panel sensor. Otherwise, re or
electric shock may result.
WARNING
Do not use the equipment in a location where metal particles could come into the equipment.
This may cause an electric shock.

1-2
For Safe Operation
1
DR-ID1270 Operation Manual 897N120821E
WARNING
Do not disassemble or remodel the equipment. Otherwise, re or electric shock may result.
Keep away from the parts inside the product, which may cause electric shock. If you touch
them accidentally, death or severe injury may result.
WARNING
Do not hit or drop the equipment or subject it to severe shock. Otherwise, the equipment may
be damaged. If the damaged equipment is used, re or electric shock may result.
In addition, do not apply strong pressure onto the at panel sensor.
If applied, the at panel sensor deforms and the waterproof function may be compromised.
WARNING/AVERTISSEMENT
Do not use the at panel sensor without the battery packs. If the battery packs are not
attached, an electric shock may result.
N’utilisez pas le détecteur à panneau plat sans les batteries. Si les batteries ne sont pas
connectées, un choc électrique risque de se produire.
WARNING
Make sure to use the optional parts recommended by us. Failure to use the optional parts
recommended by us may result in damage to the equipment and/or electric shock and injury.
CAUTIONS
As the cables of the equipment are long, be careful not to entangle the cables during use.
Also, be careful not to trip over the cables. Falls could result in injury.
CAUTIONS
Do not store magnetic media near the DR system and control cabinet. Otherwise, magnetism
generated by the equipment may cause the data to be lost.
CAUTIONS
Keep the equipment away from patient’s body uids, chemicals, water, etc.
Otherwise, it may become damaged, causing re or electric shock.
If necessary, protect the at panel sensor by covering it with a disposable bag.
Explosion Warnings
WARNING
Because this equipment is not explosion-proof, do not use combustible and explosive gases
near the equipment.
WARNING
Flammable gasses may stay in the room after disinfection. If you turn the system on just after
disinfection, ensure that the room is well ventilated before powering on the system.

1-3
For Safe Operation
1
DR-ID1270 Operation Manual 897N120821E
Warnings for Abnormalities
WARNING
If any of the following occurs, immediately turn off the power of each unit, unplug the power
cable from the outlet, and then contact our ofcial dealer or FUJIFILM Representative.
● When smoke, strange odor, or abnormal sound is present.
● When a foreign object (such as a metal object) or liquid enters the product.
● When the equipment is dropped or hit and is damaged.
Avertissements relatifs aux anomalies
AVERTISSEMENT
Si l’une des conditions répertoriées ci-après se produit, mettez immédiatement chaque unité
hors tension, débranchez le cordon d’alimentation de la prise secteur, puis contactez notre
revendeur agréé ou notre représentant FUJIFILM.
● En cas de présence de fumée, d’une odeur étrange ou d’un bruit anormal.
● En cas de pénétration d’un corps étranger (comme un objet métallique) ou d’un liquide dans
le produit.
● En cas d’endommagement de l’équipement suite à une chute ou à un impact.
Installation Precautions
CAUTIONS
Do not install the equipment in a location with the following conditions.
● Where the temperature changes sharply.
● Close to heat sources such as a heater.
● Where the equipment may be exposed to water due to water leakage or ingress.
● Where corrosive gas may be generated.
● Where there is excessive dust.
● Where the equipment is subject to frequent or excessive vibration/shock.
● Where the equipment is exposed to direct sunlight.
● Where there is no ventilator.
CAUTIONS
When the power supply unit is installed, be sure to use the Retaining bracket for MP or xing
metal ttings to prevent its overturning.
CAUTIONS
Use the equipment on a at place. If the equipment falls, it may cause damage to the equipment
or personal injury.
CAUTIONS
When you move the equipment, place it in the cassette storage box of a mobile X-ray unit or hold
it by hand to prevent it from falling. If the cart is used to move the equipment, place it horizontally.
CAUTIONS
For veterinary or mobile applications, contact our ofcial dealer or FUJIFILM Representative.

1-4
For Safe Operation
1
DR-ID1270 Operation Manual 897N120821E
CAUTIONS
When the devices are used outdoors in wireless communication mode, contact our ofcial
dealer or FUJIFILM Representative.
CAUTIONS/ATTENTION
Do not place any object in a place where removal of the power cable is prevented.
Ne placez aucun objet à un emplacement gênant le débranchement du câble d’alimentation.
CAUTIONS
To ensure optimal image quality, it is recommended that you do not use the at panel sensor
near devices (motor, transformer, switching supply, etc.) that generate electromagnetic noise.
CAUTIONS
To ensure optimal image quality, it is recommended that you do not place the cables (power
cable, communication cable, etc.) of the equipment near devices (motor, transformer, switching
supply, etc.) that generate electromagnetic noise and their cables.
CAUTIONS
Do not install the power supply unit in a place where it may be contacted inadvertently. In
addition, take care not to make contact with the power supply unit except when operating the
main switch. If the fan inside the power supply unit malfunctions, the power supply unit may
become hot, causing injury.
Connection Instructions
WARNING
Make sure that the devices to be connected to the equipment are authorized for connection.
WARNING
Connect the panel unit DR-ID1270 only to the access point, image processing unit or the
control cabinet.
Precautions on External Network Connection
CAUTIONS
When a setting of the network to which the equipment is connected has been changed,
check that the change does not affect the system operation and take measures if necessary.
The setting change may include the following:
● Change of connection destination
● Addition of devices
● Removal of devices
● Update of devices
● Upgrade of devices