Fujitsu F2MC-8FX Series Installation and operating instructions

Fujitsu Microelectronics (Shanghai) Co., Ltd.
Application Note
MCU-AN-500068-E-10
F²MC-8FX FAMILY
8-BIT MICROCONTROLLER
MB95310 SERIES
LQFP80 PGM ADAPTOR
APPLICATION NOTE

LQFP80 PGM ADAPTOR V1.0
Revision History
MCU-AN-500068-E-10– Page 2
Revision History
Date Author Change of Records
2009-12-17 Jane Li V1.0, First draft
This manual contains 21 pages.
© 2009 Fujitsu Microelectronics (Shanghai) Co., Ltd
1. The products described in this manual and the specifications thereof may be changed without prior notice.
To obtain up-to-date information and/or specifications, contact your Fujitsu sales representative or Fujitsu
authorized dealer.
2. Fujitsu will not be liable for infringement of copyright, industrial property right, or other rights of a third party
caused by the use of information or drawings described in this manual.
3. The contents of this manual may not be transferred or copied without the express permission of Fujitsu.
4. The products contained in this manual are not intended for use with equipments which require extremely
high reliability such as aerospace equipments, undersea repeaters, nuclear control systems or medical
equipments for life support.
5. Some of the products described in this manual may be strategic materials (or special technology) as defined
by the Foreign Exchange and Foreign Trade Control Law. In such cases, the products or portions thereof
must not be exported without permission as defined under the law.

LQFP80 PGM ADAPTOR V1.0
Revision History
MCU-AN-500068-E-10– Page 3
REVISION HISTORY............................................................................................................ 2 
1  INTRODUCTION.............................................................................................................. 4 
2  APPLICATION ENVIRONMENT...................................................................................... 5 
2.1  Mother Board .......................................................................................................... 5 
2.2  Debug Tool.............................................................................................................. 5 
2.3  SOFTUNE............................................................................................................... 6 
2.4  USB Programmer.................................................................................................... 6 
3  HARDWARE CONNECTION ........................................................................................... 7 
3.1  Independent Usage................................................................................................. 7 
3.2  Used with Mother Board.......................................................................................... 9 
4  PROGRAM FUNCTION ................................................................................................. 12 
4.1  Use MB95310 Series USB Programmer to Program ............................................. 12 
4.2  Use F
2
MC-8L/8FX SOFTUNE to Program............................................................. 12 
5  SCHEMATIC.................................................................................................................. 17 
5.1  LQFP80 PGM Adaptor .......................................................................................... 17 
6  PN DEFINITION RULE .................................................................................................. 18 
7  PN LIST OF APPLICABLE MCUS................................................................................. 19 
8  MORE INFORMATION .................................................................................................. 20 
9  APPENDIX..................................................................................................................... 21 

LQFP80 PGM ADAPTOR V1.0
Chapter 1 Introduction
MCU-AN-500068-E-10– Page 4
1 Introduction
The MB95310 LQFP80 PGM adapter is developed mainly as an independent on-board
programming and debugging tool for MB95310 series LQFP80 package MCU. Its original
function of programming and debugging after being installed on the MB95310 series EV
board still remains. The picture of MB95310 series LQFP80 PGM adaptor is shown in Figure
1.1.Four 20-pin connectors are used to connect with MB95310 EV board. The PN of the
MB95310 LQFP80 PGM is FMCDC-8FX-PGMA-07080050.
Figure 1.1: MB95310 LQFP80 PGM adaptor

LQFP80 PGM ADAPTOR V1.0
Chapter 2 Application Environment
MCU-AN-500068-E-10– Page 5
2 Application Environment
This chapter introduces application environment of MB95310 LQFP80 PGM adaptor.
2.1 Mother Board
The mother board of MB95310 LQFP32 PGM adaptor is MB95310 EV board V1.1, as below
picture. It can be gotten from MB95310 LCD EV Board (PN: MB2146-450-E).
Figure 2.1: MB95310 EV Board V1.1
2.2 Debug Tool
The debug tool is BGMA (BGM Adaptor), the type of it is MB2146-08-E, as below picture.
Figure 2.2: BGM Adaptor

LQFP80 PGM ADAPTOR V1.0
Chapter 2 Application Environment
MCU-AN-500068-E-10– Page 6
2.3 SOFTUNE
SOFTUNE is used to program and debug, as software development environment. The
version of it is F2MC-8L/8FX SOFTUNE Workbench V30L31, as below picture. It can be
downloaded from the following website.
Web: http: //www.fujitsu.com/cn/fmc/service/mcu/tools.
Figure 2.3: SOFTUNE Version
2.4 USB Programmer
The MB95310 series USB programmer is not support by far and will be updated later.

LQFP80 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500068-E-10– Page 7
3 Hardware Connection
This chapter introduces hardware connection when it is used independently or with mother
board.
MB95310 LQFP32 PGM adaptor can be used to program and debug independently or after
being installed to the mother board. Hardware preparations for each case are described in
Section 3.1and Section 3.2 respectively.
3.1 Independent Usage
When using MB95310 LQFP80 PGM adaptor independently for programming, we should fix
MCU on the socket first. Then following steps should be implemented.
Figure 3.1: Independent Usage Preparation

LQFP80 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500068-E-10– Page 8
(1) Connect BGMA to PC
(2) Connect PGM adaptor board to BGMA
(3) Power on the PGM adaptor board, the typical input voltage is 3.3V
Figure 3.2: Hardware Connection for Independent Usage
(2)
(1)
(3)

LQFP80 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500068-E-10– Page 9
3.2 Used with Mother Board
(1) MB95310 series EV board V1.1 is the mother board of LQFP80 PGM adaptor board.
First remove the MB95310 chip mounted on the mother board.
Figure 3.3: Remove MCU from Mother Board
Remove MCU

LQFP80 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500068-E-10– Page 10
(2) Install the MB95F310 chip onto the adaptor socket.
.
Figure 3.4: Place MCU on Adaptor Board
(3) Fix the adaptor board to the mother board.
Figure 3.5: Fix Adaptor Board on the Mother Board

LQFP80 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500068-E-10– Page 11
(4) Connect BGMA to PC.
(5) Connect PGM adaptor board to BGMA.
(6) Power on the EV-board.
Figure 3.6: Process (4)-(6)
(6)
(5)

LQFP80 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500068-E-10– Page 12
4 Program Function
This chapter introduces programming steps using either MB95310 series USB programmer
or F
2
MC-8L/8FX SOFTUNE Workbench V30L31.
MB95310 series MCU can be programmed through MB95310 series USB programmer or
F
2
MC-8L/8FX SOFTUNE Workbench V30L31. Section 4.1 and section 4.2 introduce
programming steps with MB95310 series USB programmer and F
2
MC-8L/8FX SOFTUNE
Workbench V30L31 respectively.
4.1 Use MB95310 Series USB Programmer to Program
This function is not support by far and will be updated later.
4.2 Use F
2
MC-8L/8FX SOFTUNE to Program
(1) Open a project (E.g. MB95F310 LCD EV-Board project) using SOFTUNE.
Figure 4.3: Open Demo Project

LQFP80 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500068-E-10– Page 13
(2) Please select the MCU type to MB95F310 in “Project/Setup Project…/MCU”.
Figure 4.4: Set MCU Type
(3) In “Project/Setup Project…/Linker”, set “Disposition/Connection” in Category, then select
_INROM01 and click “Set Section…” After that, a dialog window will pop up as shown in
Figure 4.6 below. Set Const (named @INIT) and Dirconst (named @DIRINIT) as shown
in Figure 4.7 and Figure 4.8.
Select MCU

LQFP80 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500068-E-10– Page 14
Figure 4.5: Disposition Display Window
Figure 4.6: Section Setting Window
(3.1) Select
(3.2) Select
(3.3) Click

LQFP80 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500068-E-10– Page 15
Figure 4.7: Set Const Section
Figure 4.8: Set Dirconst Section
(3.5) set section name
(3.4) Select
(3.6) Click
(3.8) set section name
(3.7) Select
(3.9) Click

LQFP80 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500068-E-10– Page 16
(4) Compile project.
(5) Start debugging.
Figure 4.9: Start Debugging
(6) Run (code update).
(7) End debugging.
Notes:
SOFTUNE environment can also be used to debug, however if users only need to do
programming, DO NOT set any breakpoint before step 6, or error code will be programmed.

LQFP80 PGM ADAPTOR V1.0
Chapter 5 Schematic
MCU-AN-500068-E-10– Page 17
5 Schematic
This chapter demonstrates schematic of MB95310 PGM adaptor.
5.1 LQFP80 PGM Adaptor
Figure 5.1: LQFP80 PGM Adaptor Schematic

LQFP80 PGM ADAPTOR V1.0
Chapter 6 PN Definition Rule
MCU-AN-500068-E-10– Page 18
6 PN Definition Rule
The part number of PGM adaptor is FMCDC-8FX-PGMA-07080050.
07LQFP,
080Pin count (e.g. 080 means 80 pin MCU),
050Lead pitch (e.g. 0.50mm means lead pitch 050).

LQFP80 PGM ADAPTOR V1.0
Chapter 7 PN List of Applicable MCUs
MCU-AN-500068-E-10– Page 19
7 PN List of Applicable MCUs
MCU
Series
Part Numbe
r
Footprint
MB95310 series MB95F314E
MB95F314L
MB95F316E
MB95F316L
MB95F318E
MB95F318L
LQFP80

LQFP80 PGM ADAPTOR V1.0
Chapter 8 More Information
MCU-AN-500068-E-10– Page 20
8 More Information
For more information on FUJITSU MB95310 products, please visit the following website:
Simplified Chinese Version http://www.fujitsu.com/cn/fmc
English Version http://www.fujitsu.com/cn/fmc/en