Fujitsu MB95350L Series Installation and operating instructions

Fujitsu Microelectronics (Shanghai) Co., Ltd.
Application Note
MCU-AN-500076-E-10
F²MC-8FX FAMILY
8-BIT MICROCONTROLLER
MB95350L SERIES
SOP28 PGM ADAPTOR
APPLICATION NOTE

SOP28 PGM ADAPTOR V1.0
Revision History
MCU-AN-500076-E-10– Page 2
Revision History
Date Author Change of Records
2010-03-10 Logan.chen V1.0, First draft
This manual contains 23 pages.
© 2010 Fujitsu Microelectronics (Shanghai) Co., Ltd
1. The products described in this manual and the specifications thereof may be changed without prior notice.
To obtain up-to-date information and/or specifications, contact your Fujitsu sales representative or Fujitsu
authorized dealer.
2. Fujitsu will not be liable for infringement of copyright, industrial property right, or other rights of a third party
caused by the use of information or drawings described in this manual.
3. The contents of this manual may not be transferred or copied without the express permission of Fujitsu.
4. The products contained in this manual are not intended for use with equipments which require extremely
high reliability such as aerospace equipments, undersea repeaters, nuclear control systems or medical
equipments for life support.
5. Some of the products described in this manual may be strategic materials (or special technology) as defined
by the Foreign Exchange and Foreign Trade Control Law. In such cases, the products or portions thereof
must not be exported without permission as defined under the law.

SOP28 PGM ADAPTOR V1.0
Contents
MCU-AN-500076-E-10– Page 3
Contents
REVISION HISTORY............................................................................................................ 2
1INTRODUCTION.............................................................................................................. 4
2APPLICATION ENVIRONMENT ...................................................................................... 5
2.1Mother Board .......................................................................................................... 5
2.2Debug Tool.............................................................................................................. 5
2.3SOFTUNE............................................................................................................... 6
2.4USB Programmer.................................................................................................... 6
3HARDWARE CONNECTION ........................................................................................... 7
3.1Independent Usage................................................................................................. 7
3.2Used with Mother Board.......................................................................................... 9
4PROGRAM FUNCTION ................................................................................................. 12
4.1Use MB95F350 Series USB Programmer to Program........................................... 12
4.2Use F
2
MC-8L/8FX SOFTUNE to Program............................................................. 14
5SCHEMATIC .................................................................................................................. 19
5.1SOP28 PGM Adaptor ............................................................................................ 19
6PN DEFINITION RULE .................................................................................................. 20
7PN LIST OF APPLICABLE MCUS................................................................................. 21
8MORE INFORMATION .................................................................................................. 22
9APPENDIX..................................................................................................................... 23

SOP28 PGM ADAPTOR V1.0
Chapter 1 Introduction
MCU-AN-500076-E-10– Page 4
1 Introduction
The MB95F350 SOP28 PGM adapter is developed mainly as an independent on-board
programming and debugging tool for MB95F350 series SOP24 package MCU. Its original
function of programming and debugging after being installed on the MB95F350 series EV
board still remains. The picture of MB95F350 series SOP28 PGM adaptor is shown in Figure
1.1.Two 12-pin connectors are used to connect with MB95F350 EV board. The PN of the
MB95F350 SOP28 PGM is FMCDC-8FX-PGMA-01028127.
Figure 1.1: MB95F350 SOP28 PGM adaptor

SOP28 PGM ADAPTOR V1.0
Chapter 2 Application Environment
MCU-AN-500076-E-10– Page 5
2 Application Environment
This chapter introduces application environment of MB95F350 SOP28 PGM adaptor.
2.1 Mother Board
The mother board of MB95F350 SOP28 PGM adaptor is MB95F350 EV board V1.0, as
below picture. (PN: MB2146-460-E).
Figure 2.1: MB95F350 EV Board V1.0
2.2 Debug Tool
The debug tool is BGMA (BGM Adaptor), the type of it is MB2146-08-E, as below picture.
Figure 2.2: BGM Adaptor

SOP28 PGM ADAPTOR V1.0
Chapter 2 Application Environment
MCU-AN-500076-E-10– Page 6
2.3 SOFTUNE
SOFTUNE is used to program and debug, as software development environment. The
version of it is F2MC-8L/8FX SOFTUNE Workbench V30L31, as below picture. It can be
downloaded from the following website.
Web: http: //www.fujitsu.com/cn/fmc/service/mcu/tools.
Figure 2.3: SOFTUNE Version
2.4 USB Programmer
.
Figure 2.4: USB Programmer Version

SOP28 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500076-E-10– Page 7
3 Hardware Connection
This chapter introduces hardware connection when it is used independently or with mother
board.
MB95F350 SOP28 PGM adaptor can be used to program and debug independently or after
being installed to the mother board. Hardware preparations for each case are described in
Section 3.1and Section 3.2 respectively.
3.1 Independent Usage
When using MB95F350 SOP28 PGM adaptor independently for programming, we should fix
MCU on the socket first. Then following steps should be implemented.
Figure 3.1: Independent Usage Preparation

SOP28 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500076-E-10– Page 8
(1) Connect BGMA to PC
(2) Connect PGM adaptor board to BGMA
(3) Power on the PGM adaptor board, the typical input voltage is 3.3V
Figure 3.2: Hardware Connection for Independent Usage
(2
)
(1)
(3
)

SOP28 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500076-E-10– Page 9
3.2 Used with Mother Board
(1) MB95F350 series EV board V1.0 is the mother board of MB95F350 SOP28 PGM
adaptor board. First remove the MB95F350 chip mounted on the mother board.
Figure 3.3: Remove MCU from Mother Board
Remove
MCU

SOP28 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500076-E-10– Page 10
(2) Install the chip onto the adaptor socket.
.
Figure 3.4: Make sure MCU on Adaptor Board
(3) Fix the adaptor board to the mother board.
Figure 3.5: Fix Adaptor Board on the Mother Board

SOP28 PGM ADAPTOR V1.0
Chapter 3 Hardware Connection
MCU-AN-500076-E-10– Page 11
(4) Connect BGMA to PC.
(5) Connect PGM adaptor board to BGMA.
(6) Power on the EV-board.
Figure 3.6: Process (4)-(6)
(6)
(5)

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 12
4 Program Function
This chapter introduces programming steps using either MB95F350 series USB programmer
or F2MC-8L/8FX SOFTUNE Workbench V30L31.
MB95F350 series MCU can be programmed through MB95F350 series USB programmer or
F
2
MC-8L/8FX SOFTUNE Workbench V30L31. Section 4.1 and section 4.2 introduce
programming steps with MB95F350 series USB programmer and F
2
MC-8L/8FX SOFTUNE
Workbench V30L31 respectively.
4.1 Use MB95F350 Series USB Programmer to Program
Figure 4.1: Open USB Programmer window
Figure 4.2: Open mhx file in ABS folder

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 13
Figure 4.3: click full operation
Figure 4.4: star earsing and programming

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 14
Figure 4.5: star earsing and programming finished
4.2 Use F
2
MC-8L/8FX SOFTUNE to Program
(1) Open a project (E.g.: IIC_EV) using SOFTUNE.
Figure 4.6: Open Demo Project

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 15
(2) Please select the MCU type to in “Project/Setup Project…/MCU”.
Figure 4.7: Set MCU Type
(3) In “Project/Setup Project…/Linker”, set “Disposition/Connection” in Category, then select
_INROM01 and click “Set Section…” After that, a dialog window will pop up as shown in
Figure 4.6 below. Set Const (named @INIT) and Dirconst (named @DIRINIT) as shown
in Figure 4.7 and Figure 4.8.
Select MCU

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 16
Figure 4.8: Disposition Display Window
Figure 4.9: Section Setting Window
(3.1) Select
(3.2) Select
(3.3) Click

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 17
Figure 4.10: Set Const Section
Figure 4.11: Set Dirconst Section
(3.5) set section name
(3.4) Select
(3.6) Click
(3.8) set section name
(3.7) Select
(3.9) Click

SOP28 PGM ADAPTOR V1.0
Chapter 4 Program Function
MCU-AN-500076-E-10– Page 18
(4) Compile project.
(5) Start debugging.
Figure 4.12: Start Debugging
(6) Run (code update).
(7) End debugging.
Notes:
SOFTUNE environment can also be used to debug, however if users only need to do
programming, DO NOT set any breakpoint before step 6, or error code will be programmed.

SOP28 PGM ADAPTOR V1.0
Chapter 5 Schematic
MCU-AN-500076-E-10– Page 19
5 Schematic
This chapter demonstrates schematic of MB95F350 PGM adaptor.
5.1 SOP28 PGM Adaptor
Figure 5.1: SOP28 PGM Adaptor Schematic

SOP28 PGM ADAPTOR V1.0
Chapter 6 PN Definition Rule
MCU-AN-500076-E-10– Page 20
6 PN Definition Rule
The part number of PGM adaptor is FMCDC-8FX-PGMA-01028127.
01 SOP,
028Pin count (e.g. 028 means 28 pin MCU),
127Lead pitch (e.g. 127 means lead pitch 1.27mm).