Fujitsu fi-6110 User manual

Getting Started
Getting Started
fi-6110 Image Scanner
fi-6110 Image Scanner
1
Thank you for purchasing fi-6110 Color Image Scanner (hereinafter referred to as "the scanner").
This manual describes the preparation required for use of the scanner. Follow the preparation procedures
described in this manual.
Make sure to read the "Safety Precautions" document provided with the scanner before use.
Read the Operator’s Guide (PDF) included in the Setup DVD-ROM for information about the scanner’s
operation procedures, daily care, consumables replacement, and troubleshooting.
July 2013
<Trademarks and registered trademarks>
Microsoft, Windows, Windows Server, Windows Vista, Excel, and SharePoint are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Word is a product of Microsoft Corporation in the United States.
ISIS is a registered trademark or trademark of EMC Corporation in the United States.
ABBYY™ FineReader™ Engine © ABBYY. OCR by ABBYY
ABBYY and FineReader are trademarks of ABBYY.
ScanSnap, ScanSnap Manager, and PaperStream are registered trademarks of PFU LIMITED in Japan.
Other company names and product names are the registered trademarks or trademarks of the respective
companies.
© PFU LIMITED 2010-2013
P3PC-3002-04EN

2
Checking the Components
Make sure that all items shown below are included in the package. If any other packaging is provided, make
sure to store it as well. Make sure to handle the components with care.
The box and packaging materials are required for storage and transportation of the scanner. Do not throw
them away. If anything is missing or damaged, contact your FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
Safety Precautions
The provided "Safety Precautions" document
contains important information about the safe use
of the scanner. Before using the scanner, make
sure to read and understand the information
provided in the "Safety Precautions" document.
Symbols Used in This
Manual
The following symbols are used in this manual.
Removing the Protective
Packaging
The scanner comes in a variety of protective
packaging. Follow the procedure described below
to remove the packaging before using the
scanner.
1. Open the stacker, and peel off the tape to
remove the protective foam sheet from the
ADF.
Scanner (× 1) USB Cable (× 1)AC Cable (× 1)
ADF Paper Chute
(× 1)
Setup DVD-ROM (× 1)
AC Adapter (× 1)
Carrier Sheet (× 1)
Safety Precautions (× 1)
Note: The contents may vary depending on the country.
Symbol Description
This symbol alerts operators to an
operation that, if not strictly
observed, may result in severe
injury or death.
This symbol alerts operators to an
operation that, if not strictly
observed, may result in safety
hazards to personnel or damage
to equipment.
WARNING
CAUTION
This symbol alerts particularly
important information. Be sure to
read this information.
This symbol alerts operators to
helpful advice regarding
operation.
Protective
Foam Sheet
and Tape
ADF
Stacker

3
2. Pull the ADF release tab to open the ADF,
and pull the tape to remove the protective
card.
Installing the Software
The following software are bundled with the
scanner:
zPaperStream IP (TWAIN) Driver
Conforms to the TWAIN standard. Used when
you operate the scanner using TWAIN-
compliant applications.
zPaperStream IP (ISIS) Driver
Conforms to the ISIS standard. Used when you
operate the scanner using ISIS-compliant
applications.
zSoftware Operation Panel
Configure various settings such as the
operation of the scanner and managing the
consumables. Installed together with the
PaperStream IP (TWAIN) driver and
PaperStream IP (ISIS) driver.
zError Recovery Guide
Shows the error status and countermeasures
when an error occurs. Installed together with
the PaperStream IP (TWAIN) driver and
PaperStream IP (ISIS) driver.
zPaperStream Capture
An image scanning application that supports
the PaperStream IP (TWAIN) driver and
PaperStream IP (ISIS) driver. By defining scan
settings as document profiles, you can
customize the settings according to your
preference.
zScanSnap Manager for fi Series
An application that scans images with the driver
settings that are used exclusively for ScanSnap
Manager for fi Series. PaperStream IP (TWAIN)
driver is required to use this application.
Enables easy scanning with a single button.
zScan to Microsoft SharePoint
An application that allows you to upload your
files easily from ScanSnap Manager for fi
Series to a SharePoint site. Can be used to
scan from ScanSnap Manager for fi Series.
zABBYY FineReader for ScanSnap™
Bundled for use with ScanSnap Manager for fi
Series, this application converts scanned
images into Microsoft® Office (Word/Excel®/
PowerPoint®) files. Can be used to scan from
ScanSnap Manager for fi Series.
zManual
Includes Safety Precautions, Getting Started
and Operator's Guide.
zOther Software (Legacy)
Software that were bundled with older versions
of scanners are also included.
zTWAIN Driver
Conforms to the TWAIN standard. Used when you
operate the scanner using TWAIN-compliant
applications.
zISIS Driver
Conforms to the ISIS standard. Used when you
operate the scanner using ISIS-compliant
applications.
zImage Processing Software Option (trial)
A software option featuring advanced binarization
of scanned images.
zScandAll PRO
A TWAIN/ISIS-compliant image scanning
application. You can define scanning settings as
batch profiles to suit your various operation
requirements. By defining scanning settings as
batch profiles, you can easily perform scans in
accordance with various operation requirements.
zScandAll PRO ScanSnap mode Add-in
(hereinafter referred to as "ScanSnap mode")
An add-in application which provides a different set
of driver settings as an alternative to using
ScandAll PRO. TWAIN driver is required to use this
application. Enables easy scanning with a single
button. ScandAll PRO must be installed in order to
install this software.
zScan to Microsoft SharePoint
An application that allows you to upload your files
easily from ScandAll PRO to a SharePoint site.
Can be installed together with ScandAll PRO.
zABBYY FineReader for ScanSnap™
Bundled for use with ScanSnap mode, this
application converts scanned images into
Microsoft®Office (Word/Excel®/PowerPoint®)
files. Can be installed together with ScanSnap
mode.
Bundled Software
ADF Release
Tab
ADF
Protective
Card and
Tape

4
System requirements are as follows.
*1: ScandAll PRO, ScandAll PRO ScanSnap
mode Add-in, Scan to Microsoft SharePoint,
and ABBYY FineReader for ScanSnap™ are
not supported.
*2: The software operates as a desktop
application.
*3: Disk space corresponding to the resulting
scanned file size is required when scanning
documents.
*4: PaperStream IP, PaperStream Capture and
ScanSnap Manager for fi Series are not
supported.
System Requirements
Operating
system
zWindows®XP Home Edition
(Service Pack 3 or later)
zWindows®XP Professional
(Service Pack 3 or later)
zWindows®XP Professional x64
Edition (Service Pack 2 or later)
zWindows Server®2003, Standard
Edition (*1) (*4)
zWindows Server®2003, Standard
x64 Edition (*1) (*4)
zWindows Server®2003 R2,
Standard Edition
(Service Pack 2 or later) (*4)
zWindows Server®2003 R2,
Standard x64 Edition
(Service Pack 2 or later) (*4)
zWindows Vista®Home Basic (32-
bit/64-bit) (Service Pack 1 or later)
zWindows Vista®Home Premium
(32-bit/64-bit)
(Service Pack 1 or later)
zWindows Vista®Business (32-bit/
64-bit) (Service Pack 1 or later)
zWindows Vista®Enterprise (32-bit/
64-bit) (Service Pack 1 or later)
zWindows Vista®Ultimate (32-bit/
64-bit) (Service Pack 1 or later)
zWindows Server®2008 Standard
(32-bit/64-bit)
zWindows Server®2008 R2,
Standard (64-bit)
zWindows®7 Home Premium (32-
bit/64-bit)
zWindows®7 Professional (32-bit/
64-bit)
zWindows®7 Enterprise (32-bit/64-
bit)
zWindows®7 Ultimate (32-bit/64-bit)
Operating
system
zWindows Server®2012 Standard
(64-bit) (*2)
zWindows®8 (32-bit/64-bit) (*2)
zWindows®8 Pro (32-bit/64-bit) (*2)
zWindows®8 Enterprise (32-bit/64-
bit) (*2)
CPU Intel®Core™ 2 Duo 2.2 GHz or
higher recommended
Memory 1 GB or more recommended
Display
resolution
1024 x 768 or higher, 65536 colors
or more
Hard disk
space
1.3 GB or more of free hard disk
space is required (*3)
DVD drive Essential for installing the software
Interface USB2.0 (High-Speed)
Windows Vista®screen examples are
used to explain the operations. The
screens and operations may differ slightly
depending on the operating system you
are using.
Where there is no distinction between the
different versions of the operating system
shown in the table of system
requirements, the general term Windows®
is used.

5
Install the bundled software from the Setup DVD-
ROM in the following procedure.
Note that there are two ways to install the bundled
software: select [Installation (Recommended)] to
install all the software required to operate the
scanner, or [Installation (Custom)] to select and
install the software as needed.
■Installation (Recommended)
The following software are installed:
zPaperStream IP (TWAIN) Driver
zSoftware Operation Panel
zError Recovery Guide
zPaperStream Capture
zScanSnap Manager for fi Series
zABBYY FineReader for ScanSnap™
zManual
1. Turn on the computer and log onto
Windows®as a user with Administrator
privileges.
2. Insert the Setup DVD-ROM into the DVD
drive.
DThe [fi Series Setup] screen appears.
3. Click the [Installation (Recommended]
button.
4. Follow the instructions on the screen to
proceed with the installation.
■Installation (Custom)
1. Perform steps 1. to 2. in "Installation
(Recommended)" (page 5).
2. Click the [Installation (Custom)] button.
3. Select the check box for the software to
install and click the [Next] button.
4. Follow the instructions on the screen to
proceed with the installation.
Installing the Bundled Software
If an old version of the software is
installed already, uninstall it first. For
details about the uninstallation
procedures, refer to "A.4 Uninstalling the
Software" in the Operator's Guide.
If the [fi Series Setup] screen does not
appear, double-click "Setup.exe" in
the Setup DVD-ROM via Windows
Explorer or [Computer].

6
Installing the Scanner
The following describes how to install the scanner.
1. Place the scanner at its installation site.
2. Attach the ADF paper chute.
Insert the tabs on the ADF paper chute into
the slots on the back of the scanner, and
push in to lock it firmly.
Connecting the Cables
The following describes how to connect the cables
between the scanner and your computer.
1. Make sure that the computer is turned off.
2. Connect the USB cable with the USB
connector of the scanner and the USB port
of the computer.
Carry the scanner by supporting it
from the bottom.
143
(5.63)
292
130
380
850
493.5
(14.96)
(33.46)
(19.43) (11.50)
(5.12)
Scanner's Dimensions
Unit: mm (in.)
Installation Space
Tab
ADF Paper Chute
Side Guide
CAUTION
Do not use AC adapters other than the one
supplied with this scanner. Doing so may
cause damage to the scanner.
Manufacturer: Sanken Electric Co., Ltd.
Model number: SED80N2-24.0
zBe sure to use the USB cable which
comes as an accessory with this
scanner.
zWhen connecting to an USB hub,
use the first stage USB hub that is
closest to the computer. If you use
the second or later hub stages, the
scanner may not operate correctly.
zIf you connect the scanner with USB
2.0, it is required that the USB port
and the hub be compliant with USB
2.0. The scanning speed slows down
when you connect the scanner with
USB 1.1.
zConnect the USB cable with the side
showing the USB mark facing up.
1
3
2
2
44
USB Connector
AC Cable
USB Cable
Power Connector
AC Adapter
USB mark should
face up

7
3. Connect the AC cable with the AC adapter
(hereinafter referred to as "the power
cable").
4. Connect the power cable to the power
connector of your scanner and to the AC
outlet.
Test-Scanning Documents
Using ScandAll PRO, you can test-scan
documents to check if they are scanned correctly.
For details about scanning documents by using
PaperStream Capture and the PaperStream IP
driver, refer to the help of each software.
The following describes how to test-scan a
document:
1. Press the [Power] button on the operator
panel of the scanner.
DThe power is turned on, and the [Power]
button lights in green.
During initialization, the Function Number
Display of the operator panel changes as
follows: "8" J"P" J"0" J"1". The
scanner is ready when "1" is displayed.
2. Turn on your computer.
DThe scanner is automatically detected.
3. Load a sheet into the scanner.
1. Pull out the chute extension 1 and chute
extension 2 according to the length of the
sheet.
2. Load the document in the ADF paper chute.
Set the sheet with its front side (scanning
side) facing the ADF paper chute.
WARNING
Be sure to use the supplied power cable.
The following cases may cause electrical
shock or malfunction.
zUsing a power cable other than that
supplied
zUsing the supplied power cable for other
devices
When you plug the AC cable into an
outlet, the [Power] button of the
operator panel on the scanner will
flash once. Note that this is an initial
diagnosis and not a malfunction.
If "1" is not shown in the Function
Number Display, refer to "Chapter 8
Troubleshooting" in the Operator's
Guide.
When you press the [Power] button,
the Check LED will flash once. Note
that this is an initial diagnosis and not
a malfunction.
When the [Found New Hardware]
dialog box appears, select [Locate and
install driver software
(recommended)], and install the driver
by following the on-screen
instructions.
Check
Function
Send to
Scan
/Stop
Power
Function
Number
Display
[Power] Button
Check LED

8
3. Adjust the side guides to the width of the
sheet.
4. Lift up the stacker and stacker extension
according to the length of the sheet.
4. Launch ScandAll PRO.
Select the [Start] menu J[All Programs] J
[Fujitsu ScandAll PRO] J[ScandAll PRO].
5. Select the [Tool] menu J[Preferences].
DThe [Setup] dialog box appears.
6. On the [Scan] tab, select a driver to use,
and then click the [OK] button.
To use a TWAIN driver, click [TWAIN].
To use an ISIS driver, click [ISIS].
7. Select the [Scan] menu J[Select
Scanner].
DThe [Select Scanner] dialog box appears.
8. Select the scanner you want to use, and
then click the [Select] button.
Select the scanner model which is connected
to your computer.
The list of scanner models varies depending
on the scanner driver installed.
9. Click the [Scan] menu J[Scan Settings].
DThe [Scan Settings] dialog box appears.
10. Clear the [Save to file] check box.
11. Click the [Scanner Setting] button.
DThe scanner driver's setup dialog box
appears.
12. Configure scanner settings such as the
resolution and paper size.
zTWAIN/ISIS drivers
Configure scan settings, and then click the
[OK] button.
13. In the [Scan Settings] dialog box, click the
[Scan] button.
DThe scanned document images are
displayed in the ScandAll PRO window.
For information about other scanning features,
refer to "Chapter 5 Various Ways to Scan" in the
Operator's Guide.
Contact for Inquiries
Refer to the contact list on the last page of the
"Safety Precautions" document.
TWAIN Driver ISIS Driver
FUJITSU fi-6110dj Fujitsu fi-6110
You only check the operation now, so
you do not have to save to file.
Stacker
Chute
Extension 1
Chute
Extension 2
Stacker
Extension
Side Guides
The scanner driver setup dialog box
may be displayed again after the [OK]
button is clicked. If this occurs, click
the [Scan] button in the dialog box.
When an error occurs in the scanner,
the Function Number Display
alternates between either "J" or "U"
and an "error number" for temporary
errors, and either "E", "H" or "L" and
an "alarm number" for device errors.
If an error occurs, refer to "Chapter 8
Troubleshooting" in the Operator's
Guide.