Fujitsu FUTRO S720 User manual

Thin Client
Operating Manual
FUTRO S720
FUTRO S920
ESPRIMO A525-L

Thank you for buying an innovative product from Fujitsu.
Latest information about our products, useful tips, updates etc. is available
on our website: "http://www.fujitsu.com/fts/"
You can find driver updates at: "http://support.ts.fujitsu.com/download"
Should you have any technical questions, please contact:
• our Hotline/Service Desk (see Service Desk list or from the Internet at:
"http://support.ts.fujitsu.com/contact/servicedesk")
• Your sales partner
• Your sales office
We hope you enjoy using your new Fujitsu system!

Published by / Contact address in the EU
Fujitsu Technology Solutions GmbH
Mies-van-der-Rohe-Straße 8
80807 Munich, Germany
"http://www.fujitsu.com/fts/"
Copyright
©Fujits
u Technology Solutions GmbH 2014. All rights reserved.
Publication Date
03/2014
Order No.: A26361-K1050-Z321-1-7619, edition 1

FUTRO S720
FUTRO S920
ESPRIMO A525-L
Operating Manual
ValidityoftheReferenceManual 5
Notational conventions 6
Ports and operating elements 7
Important notes 9
Getting started 15
Operation 25
System expansions 28
Technical data 60
Index 62

Remarks
Information on the product description meets the design specifications of Fujitsu and
is provided for comparison purposes. Several factors may cause the actual results to
differ. Technical data is subject to change without prior notification. Fujitsu rejects any
responsibility with regard to technical or editorial mistakes or omissions.
Trademarks
Fujitsu, the Fujitsu logo, ESPRIMO and FUTRO are registered trademarks of Fujitsu Limited
or its subsidiaries in the United States of America and other countries.
Kensington and Microsaver are registered trademarks of ACCO Brands.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft
Corporation in the United States and/or other countries.
Teradici and PCoIP are trademarks of the Teradici Corporation in the United
States of America and/or other countries.
All other trademarks specified here are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated without
the prior written consent of Fujitsu.
No part of this publication may be saved or transferred by any electronic means
without the written approval of Fujitsu.

Contents
Contents
ValidityoftheReference Manual ....................................................... 5
Notationalconventions ................................................................ 6
Portsand operatingelements ......................................................... 7
Frontview .............................................................................. 7
Rearview .............................................................................. 8
Importantnotes ........................................................................ 9
Safetynotes ............................................................................ 9
Important notes on preparing your FUTRO S720/S920 or ESPRIMO A525-L for use via the
Power over Ethernet module ............................................................. 10
Important notes on preparing your FUTRO S920 for use with an external graphics card . ...... 10
Transporting the device .................................................................. 11
Cleaning the device ..................................................................... 11
Energy saving, disposalandrecycling .................................................... 12
FCC Compliance Statement ............................................................. 13
FCC Class B ComplianceStatement .................................................. 13
CEmarking ............................................................................ 14
Gettingstarted ......................................................................... 15
Settingupthedevice .................................................................... 15
Vertical operating position . ........................................................... 15
Horizontal operating position . . ....................................................... 18
Connecting external devices . . ........................................................... 20
Connecting the cables . .............................................................. 20
Disconnecting the cables . . . . . ....................................................... 20
Portsonthedevice .................................................................. 21
Connecting a monitor . . . . . ........................................................... 21
Connecting the mouse . . . . ........................................................... 22
Connecting the keyboard . ........................................................... 22
Connecting external devices to the serial interface . .................................... 23
Connecting external devices to the USB ports . ........................................ 23
Connecting microphone, headphones, line-out and line-in devices . . ..................... 24
Connecting the mains adapter . ....................................................... 24
Connecting the device to the network (LAN) . . . ............................................ 24
Operation .............................................................................. 25
Switch thedeviceon .................................................................... 25
Switchingoffthedevice ................................................................. 25
Activatingpower-savingmode ........................................................ 25
Open BIOSSetup ....................................................................... 25
PXE system boot . ...................................................................... 25
Calling the PXE system boot configurationmenu ....................................... 26
Systemexpansions .................................................................... 28
Overview of optional system components . . . . . ............................................ 28
PossiblecombinationsfortheFUJITSUThinClientFUTROS920 ....................... 29
Information about boards . . . . . ........................................................... 30
Openingthecasing ..................................................................... 31
Addingmemory ......................................................................... 32
Removingmemorymodules .......................................................... 32
Fujitsu 3

Contents
Installingamemorymodule .......................................................... 32
InstallingandremovingtheSmartCardreader(FUJITSUThinClientFUTROS920only) ...... 33
Installing the SmartCard reader . . . . . . ................................................. 33
Removing the SmartCard reader . . . . ................................................. 36
Information about installing and removing a speaker (optional) .............................. 37
Installing and removing a speaker: FUJITSU Thin Client FUTRO S720 / FUJITSU Thin Client
FUTROS920 ........................................................................... 37
Installingtheloudspeaker ............................................................ 37
Removingtheloudspeaker ........................................................... 40
Installing and removing a speaker: FUJITSU Desktop ESPRIMO A525-L . ................... 41
Installingaspeaker .................................................................. 41
Removingaspeaker ................................................................ 47
Installing and removing a Power over Ethernet module (optional) . .......................... 51
Installing the Power over Ethernet module ............................................. 52
Removing the Power over Ethernet module . . . ......................................... 54
Installing and removing a board . . ........................................................ 55
Installing the board . . ................................................................ 55
Removing the board . ................................................................ 57
Replacingthelithiumbattery ............................................................. 58
Closingthecasing ...................................................................... 59
Technicaldata ........................................................................ 60
FUTRO/ESPRIMO . . . . . . ................................................................ 60
ACadapter ............................................................................. 61
Index .................................................................................. 62
4Fujitsu

Validity of the Reference Manual
Validity of the Reference Manual
This Reference Manual is valid for the following systems:
• FUJITSU Thin Client FUTRO S720
• FUJITSU Thin Client FUTRO S920
• FUJITSU Desktop ESPRIMO A525-L
Fujitsu 5

Notational conventions
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
these warnings could pose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.
Indicates important information for the proper use of the device.
►Indicates an activity that must be performed
Indicates a result
This font indicates data entered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)
This font indicates information that is displayed on the screen by a program, e.g.:
Installation is complete.
This font indicates
• terms and texts used in a software interface, e.g.: Click on Save
• names of programsorfiles, e.g. Windows or setup.exe.
"This font" indicates
• cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For more
information, go to "http://www.fujitsu.com/fts"
• Names of CDs, DVDs and titles or designations for other materials,
e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual
Key indicates a key on the keyboard, e.g: F10
This font indicates terms and texts that are emphasised or highlighted, e.g.: Do
not switch off the device
6Fujitsu

Ports and operating elements
Ports and operating elements
Ports
This chapter presents the individual hardware components of your device. This will provide
you with an overview of the ports and operating elements on the device. Please familiarise
yourself with these components before starting to work with your device.
Front view
OnswitchOffswitchPower-onindicatorSmartCardr eaderFlashmemoryaccessHeadphone portAudiooutputMicrophone portUSB
$
#
"
!
%

1 = SmartCard reader (FUJITSU Thin Client
FUTRO S920 only, optional)
2 = Indicator for SmartCard reader
3 = Flash memory or hard disk access
4 = ON/OFF switch
5 = Microphone jack
6 = USB ports (Universal Serial Bus)
7 = Headphones port, audio output (Line Out)
Fujitsu 7

Ports and operating elements
Rear view
LANsocke tPS/2mous eportInstallationopeningPS/2keyboa rdportMonitorportSerialportUSBportsAudiooutputDCinputconnecto rAudioinp utPCIslotPCIeslotSecurityLock
2
3
8
5
7
1
4
6
10
13
12
9
11
14
15
1 = Socket for Power over Ethernet
module (optional)
2 = Audio output (Line Out)
3 = PS/2 keyboard port
4 = USB ports
5 = USB ports
6 = DisplayPort
7 = DVI-I monitor port
8 = DC input jack (DC IN)
9 = Security Lock device
10 = Serial port
11 = Serial port (only for FUJITSU Thin
Client FUTRO S920)
12 = RJ45 socket (Local Area Network)
13 = PS/2 mouse port
14 = Audio input (Line In)
15 = PCI/PCIe port (FUJITSU Thin Client
FUTRO S920 only, optional)
8Fujitsu

Important notes
Important notes
ImportantnotesNotes
In this chapter you will find information regarding safety which it is essential to
take note of when working with your device.
Safety notes
SafetynotesNote
Please follow the safety notes provided in the "Safety/Regulations" manual
as well as the safety notes given below.
When installing and operating the device, please observe the notes on ambient
conditions in "Technical data ", Page 60 and the instructions in "Getting started", Page 15.
Replace the lithium battery on the mainboard exactly in accordance with the
instructions in the "Replacing the lithium battery", Page 58 chapter.
Caution, components in the system can get very hot.
The activities described in these instructions must always be
performed with the greatest care.
Repairs to the device must only be carried out by qualified technicians. Incorrect
repairs could put the user at great risk (electric shock, hazardous energy emissions,
risk of fire)orcau
se serious damage to the equipment.
Operate the device only with the casing closed.
Power cable and mains adapter:
The supplied power cable conforms to the requirements of the country in
which you purchased your device. Make sure that the power cable is approved
for use in the country in which you intend to use it.
The mains adapter’s power cable should only be connected to a mains
socket if the device is connected.
Do not use the mains adapter for other devices.
Use only the mains adapter which is intended for use with the device,
see chapter "Technical data ", Page 60.
Make sure that the rated current of the mains adapter is not higher than that of
the power system to which you connect the mains adapter.
ON/OFF switches do not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the power socket.
Fujitsu 9

Important notes
Important notes on preparing your FUTRO S720/S920
or ESPRIMO A525-L for use via the Power
over Ethernet module
With the aid of the Power over Ethernet module, you can operate the FUTRO S720/S920
or the ESPRIMO A525-L over the LAN without any additional power connection.
You will need a suitable network infrastructure for this.
To operate the FUTRO S720/S920 or the ESPRIMO A525-L via the Power over Ethernet module,
midspan devices conforming to IEEE 802.3at and shielded CAT 5 network cable or higher quality
cable are required. Endspan devices will only be supported in conjunction with a hardware
classification. Fujitsu recommends the use of the following midspan devices:
• 1 port midspan from Microsemi PD-9501G: S26361-F1744-L10
• 12 port midspan from Microsemi PD-9512G: S26361-F1744-L20
Because of the limited power output, not all hardware configuration levels are possible for
operating the FUTRO S720/S920 or the ESPRIMO A525-L via the Power over Ethernet
module. The following hardware configurations are possible:
Internal memory expansion according to Configurator
mSATA module (FUTRO) / HDD (ESPRIMO) according to Configurator
SmartCard readerinternal SmartCard reader
Speaker internal speaker
WLAN internal WLAN module according to Configurator
PCI/PCIe cards or extra interfaces none
Depending on the system utilisation, occupancy of external interfaces (excluding the keyboard,
screen, microphone and headset) may cause overloading of the Power over Ethernet module.
In order to support the largest possible occupancy of interfaces, if an overload occurs the
performance of the system is lowered by a reduction in the CPU frequency. If the CPU frequency
is permanently reduced, the occupancy of the external interfaces must be checked and reduced
accordingly to prevent damage to the Power over Ethernet module or the midspan. Alternatively,
the system can also be connected via a suitable AC adapter (see note in this Operating
Manual). The system must be switched off before the AC adapter is connected.
If you are perhaps retrofitting a FUTRO/ESPRIMO with a Power over Ethernet module,
please pay attention to the maximum possible expansion. If PCI/PCIe expansion cards are
installed (FUTRO S920), these must be removed, otherwise the Power over Ethernet module
or the midspan may be overloaded and switched off automatically.
Important notes on preparing your FUTRO S920
for use with an external graphics card
The FUTRO S920 may in addition be fitted with a graphics card. Only specially approved
graphics cards are allowed to be used. If a graphics card is retrofittedintheFUTROS920,itis
important to note that a 65W AC adapter is needed for operation. The FUTRO S920 without a
graphics card is only supplied from the factory with a 40W AC adapter as standard.
10 Fujitsu

Important notes
Transporting the device
Device,Transpo rtati onRetransportation
Transport all parts separately in their original packaging or in a packaging which
protects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
If the device is brought from a cold environment into the room where it will be used,
condensation may occur. Before operating the device, wait until it is absolutely dry
and has reached approximately the same temperature as the installation site.
Cleaning the device
Device,Transpo rtati onRetransportationSystemu nit,see Device
Turn off all power and equipment switches and disconnect the power
plug from the mains outlet.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode
plastic (alcohol, thinner or acetone).
Never clean the device with water! Water entering into the device could
present a serious risk to users (e.g. electric shock).
Ensure that no liquid enters the system.
Thesurfacecanbecleaned with a dry cloth. If particularly dirty, use a cloth that has been
moistened in mild domestic detergent and then carefully wrung out.
Use disinfectant wipes to clean the keyboard and the mouse.
Fujitsu 11

Important notes
Energy saving, disposal and recycling
DisposalEnergysavingRecy clingDrivers&UtilitiesDVDUserDocumentatio nDVD
You can find information on these subjects in chapter "Activating power-saving mode", Page 25,on
the Recovery DVD or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/").
Information on "Ökodesign-Richtlinie":
Regulation 1275/2008, based on the EU Eco-design Directive (2009/125/EU),
defines requirements for the power consumption of electrical and electronic domestic
and office devices in stand-by and off mode.
In general, all FUTRO thin client products have been developed for energy-efficient
operation and low stand-by losses. Due to customer-specific and operating system-specific
requirements, which are the priority for optimal operation, some system settings are
necessary which deviate from the above-mentioned directive.
For administrative purposes, such as remote maintenance of systems, the "Wake-on-Lan" (WoL)
function is indispensable for our customers and is therefore a default setting. Activation of the WoL
function slightly increases the idle current and the max. permissible power draw in the Off mode can
thus be slightly exceeded. By deactivating the WoL function, it is possible to comply with the legal
requirements. Please see chapter "Activating power-saving mode", Page 25 for the procedure.
The energy saving mode (ACPI S4 Save-to-disk), which is familiar from many current mobile
and desktop systems, is not available in the embedded operating systems for technical reasons.
Therefore, it is not possible to switch devices with this operating system automatically into Off mode.
The operating system of a thin client is stored on a flash memory with optimised size and is provided
with write protection after configuration has been completed by the customer. This prevents data
security from being put at risk through frequent writing to a flash memory, such as when updating
the Swapfiles in the operating system or through other applications. Every flash memory permits
only a limited number of write cycles. Both the activated write protection and the available, limited
flash memory capacity rule out the possibility of activating energy saving mode (ACPI S4).
12 Fujitsu

Important notes
FCC Compliance Statement
If the device complies with the FCC regulations, the FCC sign can be found on the type rating plate.
FCCClassBComplianceState
ment
DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television:
This class B digital apparatus complies with Canadian ICES-003.
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital
device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian
Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in strict accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Fujitsu is not responsible for any radio or television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Fujitsu. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC and ICES rules.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or operated in conjunction
with any other antenna or transmitter.
To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject to licensing.
Users are not authorized to modify this product. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or changed in any way without signed
written permission from Fujitsu. Unauthorized modification will void the equipment
authorization from the FCC and Industry Canada and the warranty.
Fujitsu 13

Important notes
CE marking
This device complies with the requirements of EC directives 2004/108/EC "Electromagnetic
compatibility", 2006/95/EC "Low voltage directive" and 2009/125/EC "Ecodesign directive".
For this purpose, please also note the special information concerning the "Ecodesign directive"
for the FUTRO systems (see "Energy saving, disposal and recycling", Page 12).
14 Fujitsu

Getting started
Getting started
Gettingstarted
Please observe the safety information in the "Important notes", Page 9 chapter.
Settingupthedevice
In order to ensure that the casing is sufficiently ventilated and to prevent overheating,
the device must only be operated with the base foot attached.
If the device is to be built-in, adequate ventilation must be assured.
Fit the base feet for horizontal or vertical operation (see "Vertical operating
position", Page 15 and "Horizontal operating position", Page 18).
Vertical operating position
VerticaloperatingpositionOperatingpos ition,verticalBasefeetSide cover
If you wish to operate the device in the vertical operating position, use
the two feet supplied for vertical operation.
Proceed as follows to prepare the device for the vertical operating position:
►Disconnect the cables if required.
►Lay the device on its top (narrow side) as shown, on a stable, flat and clean surface.
Fujitsu 15

Getting started
1
1
1
2
2
►Hook the feet into each of the openings provided for this in the casing (1).
There are lock symbols on the foot, indicating the direction in which the
foot must be pushed during installation or removal:
• Secure and lock the foot = push to the left (closed lock)
• Unlock and release the foot = push to the right (open lock)
►Repeat for each foot: Push the outer elements of the foot evenly onto the casing
using both hands, keep the "Push" button pressed (see magnifier) and push the foot
in the direction of the arrow (2) until it is heard to engage.
16 Fujitsu