Fujitsu PRIMERGY TX1320 M5 User manual

FUJITSU Server PRIMERGY TX1320 M5
Upgrade and Maintenance Manual
Upgrade and Maintenance Manual - English
12/2021

Comments… Suggestions… Corrections…
The User Documentation Department would like to know your opinion of this manual. Your
feedback helps us optimize our documentation to suit your individual needs.
Feel free to send us your comments by e-mail to [email protected].
Documentation creation according to DIN EN ISO 9001:2015
To ensure a consistently high quality standard and user-friendliness, this documentation was
created to meet the regulations of a quality management system which complies with the
requirements of the standard DIN EN ISO 9001:2015.
cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de/en/
Copyright and Trademarks
Copyright 2021 FUJITSU LIMITED
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
–The contents of this manual may be revised without prior notice.
–Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
–No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper-V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.

Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure that
these safety notes are understood before using the product. Keep this manual
and the "Safety Notes and Regulations" manual in a safe place for easy
reference while using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures.
VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the printed circuit board
assemblies of the product and in the mouse and keyboard are limited-life
components. Use of these components beyond their operating life may result
in electrolyte leakage or depletion, potentially causing emission of foul odor or
smoke.
As a guideline, in a normal office environment (25 °C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
TX1320 M5 Upgrade and Maintenance Manual

The product is not suitable for use at visual display workplaces according to §2
of the Workplace Regulations (applies to all server systems except TX server
systems).
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, the use of an
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Upgrade and Maintenance Manual TX1320 M5

Only for Japan: About SATA HDDs
The SATA version of this server supports HDDs with SATA/BC-SATA storage
interfaces. Please note that the usage and operation conditions differ
depending on the type of HDD used.
For more information on the usage and operation conditions of each available
type of HDD, see the following internet address:
https://jp.fujitsu.com/platform/server/primergy/harddisk/
Only for Japan:
Shielded LAN cables should be used in this product.
UK Importer information
Fujitsu Services Limited
22 Baker Street, London, W1U 3BW, United Kingdom
TX1320 M5 Upgrade and Maintenance Manual

Version history
Issue
number
Issue date Description
V 1.0 12/2021 Initial release
Upgrade and Maintenance Manual TX1320 M5

Content
1 Introduction 17
1.1 Concept and target groups of this manual 17
1.2 Notational conventions 17
2 Before you start 19
2.1 Basic information 19
2.1.1 Proceeding 19
2.1.2 Advanced Thermal Design (ATD) 19
2.1.3 Installing optional components 20
2.1.4 Replacing a defective component 20
2.2 Classification of procedures 21
2.2.1 Assignment of unit categories 21
2.2.2 Customer Replaceable Units (CRU) 21
2.2.3 Upgrade and Repair Units (URU) 22
2.2.4 Field Replaceable Units (FRU) 23
2.3 Average task duration 24
2.4 Tools you need at hand 25
2.5 Documentation overview 26
2.5.1 Downloading manuals 26
2.5.2 List of documents 26
3 Important information 29
3.1 Introduction 29
3.2 Safety instructions 29
3.2.1 Basic safety instructions 29
3.2.2 Before starting up 30
TX1320 M5 Upgrade and Maintenance Manual

3.2.3 Installation and operation 30
3.2.4 Batteries 33
3.2.5 Working with optical disk drives (ODDs) and media 33
3.2.6 Laser information 35
3.2.7 Modules with Electrostatic-Sensitive Devices (ESD modules) 35
3.2.8 Transporting the server 37
3.2.9 Installing the server in the rack 38
3.2.10 Other important information 38
3.3 ENERGY STAR 39
3.4 CE conformity 39
3.5 FCC Class A Compliance Statement 40
3.6 Environmental protection 41
4 Basic hardware procedures 43
4.1 Using diagnostic information 43
4.1.1 Proceeding 43
4.2 Locating the defective server 43
4.3 Determining the error class 44
4.4 Locating the defective component 44
4.5 Shutting down the server 45
4.6 Disconnecting the power cord 46
4.7 Getting access to the component 48
4.7.1 Safety notes 48
4.7.2 Unlocking the server 49
4.7.3 Removing the server cover 50
4.7.4 Removing the accessible drive bay cover 52
4.7.5 Removing the HDD bay cover 53
Content
Upgrade and Maintenance Manual TX1320 M5

4.8 Reassembling 54
4.8.1 Safety notes 54
4.8.2 Installing the server cover 54
4.8.3 Installing the HDD bay cover 55
4.8.4 Installing the accessible drive bay cover 55
4.9 Connecting the power cord 57
4.9.1 Connecting the power cord (standard PSU, with cable tie) 57
4.9.2 Connecting the power cord (hot-plug PSU) 58
4.10 Switching on the server 60
4.11 Handling the 2.5-inch HDD cage 60
4.11.1 Removing the 2.5-inch HDD cage 60
4.11.2 Installing the 2.5-inch HDD cage 62
4.12 Handling the HDD fan modules 64
4.12.1 Removing the HDD fan module (3.5-inch HDD variant) 64
4.12.2 Installing the HDD fan module (3.5-inch HDD variant) 65
4.12.3 Removing the HDD fan module (2.5-inch HDD variant) 67
4.12.4 Installing the HDD fan module (2.5-inch HDD variant) 68
5 Basic software procedures 71
5.1 Validation 71
5.2 Starting the maintenance task 71
5.2.1 Suspending BitLocker functionality 71
5.2.2 Disabling the boot watchdog 72
5.2.3 Removing backup and optical disk media 74
5.2.4 Verifying and configuring the backup software solution 74
5.2.5 Switching on the ID indicator 74
5.3 Completing the maintenance task 75
5.3.1 Updating or recovering the BIOS and iRMC S6 75
5.3.2 Verifying system information backup or restore 78
5.3.3 Updating expansion card firmware 79
5.3.4 Reconfiguring the backup software solution 80
5.3.5 Resetting the boot retry counter 81
Content
TX1320 M5 Upgrade and Maintenance Manual

5.3.6 Resetting the error status after replacing memory modules or
CPU 82
5.3.6.1 Resetting the error status after replacing memory modules 82
5.3.6.2 Resetting the error status after replacing CPUs 84
5.3.7 Enabling the boot watchdog 86
5.3.8 Enabling replaced components in the BIOS 87
5.3.9 Verifying the system time settings 87
5.3.10 Viewing and clearing the System Event Log (SEL) 88
5.3.11 Updating the NIC configuration file in a Linux and VMware
environment 90
5.3.12 Resuming BitLocker functionality 91
5.3.13 Performing a RAID array rebuild 92
5.3.14 Looking for MAC/WWN/GUID and SAS addresses 93
5.3.14.1 Basic information 93
5.3.14.2 Looking for the MAC address of a LAN controller 93
5.3.14.3 Looking for the WWN address of a fibre channel controller 94
5.3.14.4 Looking for the GUID address of an infiniband or Omni-Path
controller 95
5.3.14.5 Looking for SAS addresses of SAS controllers for external
devices 95
5.3.15 Using the Chassis ID Prom Tool 96
5.3.16 Configuring LAN teaming 98
5.3.17 Switching off the ID indicator 99
5.3.18 Performing a fan test 100
6 Power supply unit (PSU) 101
6.1 Safety notes 101
6.2 Basic information 101
6.3 Standard power supply 103
6.3.1 Replacing the standard PSU 103
6.3.2 Converting a standard power supply to a redundant power
supply 109
6.4 Redundant power supply 116
6.4.1 Installing a hot-plug PSU 116
6.4.2 Removing a hot-plug PSU 120
Content
Upgrade and Maintenance Manual TX1320 M5

6.4.3 Replacing a hot-plug PSU 122
6.4.4 Replacing the power distribution board 124
7 Hard disk drive (HDD) / solid state drive (SSD) 133
7.1 Safety notes 133
7.2 Basic information 134
7.3 Handling HDDs or SSDs without installation frame 135
7.3.1 2.5-inch HDD/SSD and 2.5-inch installation frame 135
7.4 3.5-inch HDD configurations 137
7.4.1 Configuration with up to two 3.5-inch HDDs 137
7.4.2 Installing 3.5-inch non hot-plug HDDs 137
7.4.3 Removing 3.5-inch non hot-plug HDDs 143
7.4.4 Replacing a 3.5-inch non hot-plug HDD 148
7.5 2.5-inch HDD/SSD configurations 150
7.5.1 Configuration with up to four HDD/SSD modules 150
7.5.2 Configuration with up to eight HDD/SSD modules 150
7.5.3 Configuration with up to four PCIe SSD modules 151
7.5.4 Installing 2.5-inch HDD/SSD modules 152
7.5.5 Removing 2.5-inch HDD/SSD modules 154
7.5.6 Replacing a 2.5-inch HDD/SSD module 157
7.5.7 Replacing a 2.5-inch backplane 159
7.5.8 Upgrading configuration from up to four to up to eight 2.5-inch
HDDs/SSDs 166
7.5.9 Upgrading to 4x PCIe 2.5-inch SSD configuration 168
8 Fans 171
8.1 Safety notes 171
8.2 Basic information 171
8.3 Replacing the HDD fan (3.5-inch HDD variant) 173
8.4 Replacing the HDD fan (2.5-inch HDD variant) 176
Content
TX1320 M5 Upgrade and Maintenance Manual

9 Expansion cards and backup units 181
9.1 Safety notes 181
9.2 Basic information 182
9.3 Handling slot brackets 183
9.3.1 Installing slot brackets 183
9.3.2 Removing slot brackets 186
9.4 Handling SFP+ transceiver modules 186
9.4.1 Installing SFP+ transceiver modules 186
9.4.2 Removing SFP+ transceiver modules 192
9.5 Expansion cards 195
9.5.1 Installing expansion cards 195
9.5.2 Removing expansion cards 203
9.5.3 Replacing expansion cards 205
9.6 Flash backup unit (FBU) 207
9.6.1 Position of the FBU 207
9.6.2 Installing an FBU 208
9.6.3 Removing an FBU 215
9.6.4 Replacing an FBU 219
10 Main memory 221
10.1 Safety notes 221
10.2 Basic information 222
10.2.1 Slots and features 222
10.2.2 General memory population rules 222
10.2.3 Modes of operation 223
10.3 Installing memory modules 223
10.4 Removing memory modules 226
10.5 Replacing memory modules 227
Content
Upgrade and Maintenance Manual TX1320 M5

11 Processor (CPU) 229
11.1 Safety notes 229
11.2 Basic information 229
11.3 Upgrading or replacing the CPU 230
11.4 Replacing the heat sink 243
12 Accessible drives 245
12.1 Safety notes 245
12.2 Basic information 245
12.3 Optical disk drive (ODD) 246
12.3.1 Installing the ODD 246
12.3.2 Removing the ODD 252
12.3.3 Replacing the ODD 255
12.4 RDX drive 257
12.4.1 Installing the RDX drive 257
12.4.2 Removing the RDX drive 261
12.4.3 Replacing the RDX drive 264
13 Front panel 267
13.1 Safety notes 267
13.2 Replacing the front panel module 267
14 Front USB connector 273
14.1 Installing a front USB connector 273
14.2 Removing a front USB connector 276
14.3 Replacing a front USB connector 279
Content
TX1320 M5 Upgrade and Maintenance Manual

15 Serial interface 281
15.1 Safety notes 281
15.2 Installing the serial interface 281
15.3 Removing the serial interface 284
15.4 Replacing the serial interface 285
16 Dust cover 287
16.1 Safety notes 287
16.2 Basic information 288
16.3 Installing the dust covers 288
16.4 Removing the dust covers 293
16.5 Replacing the dust covers 297
17 System board and components 299
17.1 Safety notes 299
17.2 Basic information 299
17.3 CMOS battery 300
17.3.1 Replacing the CMOS battery 300
17.4 Trusted Platform Module (TPM) 302
17.4.1 Position of the TPM 302
17.4.2 TPM kit 303
17.4.3 Installing the TPM 303
17.4.4 Removing the TPM 306
17.4.5 Replacing the TPM 311
Content
Upgrade and Maintenance Manual TX1320 M5

17.5 iRMC microSD card 313
17.5.1 Note for embedded Lifecycle Management (eLCM) 313
17.5.2 Installing the iRMC microSD card 313
17.5.3 Removing the iRMC microSD card 315
17.5.4 Replacing the iRMC microSD card 316
17.6 M.2 SSD 317
17.6.1 Slots and bolts for M.2 SSDs 317
17.6.2 Installing an M.2 SSD 319
17.6.3 Removing an M.2 SSD 324
17.6.4 Replacing an M.2 SSD 327
17.7 Dual microSD 64GB Enterprise 329
17.7.1 Position of the Dual microSD 64GB Enterprise 329
17.7.2 Installing the Dual microSD 64GB Enterprise 329
17.7.3 Removing the Dual microSD 64GB Enterprise 332
17.7.4 Replacing the Dual microSD 64GB Enterprise 333
17.7.5 Replacing the microSD card 335
17.8 System board 337
17.8.1 Replacing the system board 337
18 Appendix A 347
18.1 Mechanical overview 347
18.1.1 Server front 347
18.1.2 Server rear 349
18.1.3 Server interior 351
18.2 Connectors and indicators 354
18.2.1 Connectors and indicators on the system board 354
18.2.1.1 Connectors and indicators on the system board 354
18.2.2 Server front 359
18.2.2.1 Connectors on the server front 359
18.2.2.2 Indicators on the front panel 360
18.2.2.3 Indicator on the ODD 363
18.2.2.4 Indicators on the RDX drive 363
18.2.2.5 Indicators on hot-plug HDD / SSD / PCIe SSD modules 364
Content
TX1320 M5 Upgrade and Maintenance Manual

18.2.3 Server rear 366
18.2.3.1 Connectors on the server rear 366
18.2.3.2 ID, CSS and Global Error indicators 367
18.2.3.3 LAN indicators 369
18.2.3.4 Indicator on hot-plug PSU 370
18.3 Acoustic indicators 371
18.4 Onboard settings 372
18.5 Minimum startup configuration 373
19 Appendix B 375
19.1 Supplied documents 375
Content
Upgrade and Maintenance Manual TX1320 M5

1 Introduction
1.1 Concept and target groups of this manual
This upgrade and maintenance manual provides instructions for the following
procedures:
–Upgrading the server configuration by adding optional hardware
components.
–Upgrading the server configuration by replacing existing hardware
components with superior ones.
–Replacing defective hardware components.
This manual focuses on on-site maintenance tasks. It is recommended to
prepare each service assignment following remote diagnostics procedures, as
described in the "ServerView Suite Local Service Concept (LSC)" manual, see
"Documentation overview" on page 26.
CAUTION
The document at hand comprises procedures of a wide range of
complexity.
▶Check the profile of qualification for technicians before assigning
tasks.
▶Before you start, carefully read "Classification of procedures" on
page 21.
1.2 Notational conventions
The following notational conventions are used in this manual:
Text in bold Indicates references to names of interface
elements.
Text in monospace Indicates commands and text to be entered by
the user.
TX1320 M5 Upgrade and Maintenance Manual 17

"Quotation marks" Indicate names of chapters and terms that are
being emphasized.
▶ Describes activities that must be performed in
the order shown.
[Abc] Indicates keys on the keyboard.
CAUTION
Pay particular attention to texts marked with this
symbol. Failure to observe this warning may
endanger your life, destroy the system or lead
to the loss of data.
Indicates additional information, notes and tips.
Indicates the procedure category in terms of
complexity and qualification requirements, see
"Classification of procedures" on page 21.
Indicates the average task duration, see
"Average task duration" on page 24.
Introduction
18 Upgrade and Maintenance Manual TX1320 M5

2 Before you start
2.1 Basic information
2.1.1 Proceeding
Before you start any upgrade or maintenance task, proceed as follows:
▶Carefully read the safety instructions, see "Important information" on
page 29.
▶Make sure that all necessary manuals are available, see "Documentation
overview" on page 26. Print the PDF files if required.
▶Make yourself familiar with the procedure categories, see "Classification of
procedures" on page 21.
▶Ensure that all required tools are available, see "Tools you need at hand" on
page 25.
2.1.2 Advanced Thermal Design (ATD)
The ATD option allows you to operate the system with a wider temperature
range either of 5 °C to 40 °C or 5 °C to 45 °C, depending on your system and
configuration.
This option can only be ordered from the
manufacturer and is indicated by the respective
logo on the identification rating plate.
CAUTION
▶In a system that is configured with ATD, only certain components
which support the respectively increased higher operating
temperature range may be installed and used. For applicable
restrictions, see the official configurator tool.
TX1320 M5 Upgrade and Maintenance Manual 19

2.1.3 Installing optional components
The operating manual of your server gives an introduction to server features
and provides an overview of available hardware options.
Use the Fujitsu ServerView Suite management software and the iRMC S6 web
interface to prepare hardware expansions. For more information about
ServerView Suite documentation, see "Documentation overview" on page 26.
Please see the following ServerView Suite topics:
–Operation
–Virtualization
–Maintenance
–Out-Of-Band Management
For the latest information on hardware options, see the hardware
configurator of your server, available online at the following address:
https://www.fujitsu.com/fts/products/computing/servers/primergy/
index.html
For Japan:
https://www.fujitsu.com/jp/products/computing/servers/primergy/
Please contact your local Fujitsu customer service partner for details on how to
order expansion kits or spare parts.
2.1.4 Replacing a defective component
The Global Error indicator on the front of the server reports defective hardware
components that need to be replaced. For more information on the controls
and indicators of your server, see the operating manual of your server and
"Connectors and indicators" on page 354.
If the system has been powered off in order to replace a non-hot plug unit, a
system of PRIMERGY diagnostic indicators guides you to the defective
component. The "Indicate CSS" button enables the indicator next to the
defective component even if the server has been switched off and
disconnected from the mains. For more information, see "Using diagnostic
information" on page 43 and "Indicators on the front panel" on page 360.
Before you start
20 Upgrade and Maintenance Manual TX1320 M5