Furniture of America CM-AC804 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 7
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Rev:18-09-25
CM-AC804
For more information contact our team: [email protected]
Phillips Screwdriver
(Not Included)

Page 2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Page 3 of 7
Cam Lock
Cam Lock Fastener Assembly
Cam Pin
Cam Lock are fasteners used to join two boards
together, usually the edge of one board (A) to the flat
side of another board (B).
Flat side
Board A
Board B
edge to
join
To use Cam Lock
Fasteners:
Step 1 - Insert
cam Pin into the
flat side of a
board. Tighten
only until snug.
Do not
over-tighten
Step 2 - Fit the
hole in the
edge of the
joining board
over the Cam
Pin. The head
of the Cam Pin
will be visible
in the large
hole in the
side of the
joining board,
as in Step 3.
Step 3 - Notice the Cam Lock has a "C" -Shaped back.
An arrow on the front points the same direction as the
open section. Insert the Cam Lock into the large hole so
the opening of the "C" fits over the head of the Cam Pin.
arrow head of the Cam Pin
Open section of
back fits over the
head os the Cam
Pin
Step 4 - Use a flat screwdriver to turn the Cam Lock
clockwise on half a turn so it locks onto the head of the
Cam Pin. Turn only until it is snug - over-tightening could
cause the Cam to bend or break.
If is will not turn the full amount, turn the Cam Pin out
(counter- clockwese ) one full turn, and try the Cam Lock
again.

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 7
Parts List
Hardware List
#A x 4pcs
Allen Key 4mm
#B x 1pc
#4 x 1pc
#5 x 1pc
Lower shelf
Foot
#1 x 1pc
Left Frame
#2 x 1pc
Right Frame
#3 x 4pcs
Upper shelf
Bolt Ø1/4" x 1-3/8"
Cam Pin Ø7mm
#C x 16pcs
Cam Lock Ø14.5mm
#D x 16pcs
#1
#2
#3
#4
#5

#1
#C
#C x 10pcs
#2
#C
#C x 5pcs
Page 5 of 7
Attach cam pins (#C) to left frame (#1).
Attach cam pins (#C) to right frame.

Page 6 of 7
#C x 1pc
#D x 10pcs
#4
#1
#4
#3
#D
#B
Attach cam pin (#C) to lower shelf (#4).
Please refer to page 3 on how to secure cam locks
(#D) onto cam pins (#C).
Align shelves (#3) to the frame (#1), then
secure by using cam locks (#D).

Page 7 of 7
#2
#D x 6pcs
#1
#4
#3
#3
#3
#3
#B
#D
#1
#2 #A #B
#A x 4pcs
#5
#D
#B
Align frame (#2) to the shelves, then secure by using cam locks (#D).
Secure both frames together by using bolts (#A).