Furniture of America CM-BK633TF User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 10
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Rev: 18-06-27
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
CM-BK633TF
For more information contact our team: [email protected]

Page 2 of 10
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

Parts List
#3 x 1pc
#4 x 1pc
#2 x 1pc
#9 x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#1 x 1pc
#5 x 1pc
#6 x 1pc
#8 x 1pc
Page 3 of 10
Lower Front Side Rail
Lower Back Side Rail
Back Guardrail
#11 x 1Set
Twin Slat Kit (13pcs)
Upper Front Side Rail
#10 x 2pcs
Front Guardrail
#12 x 3pcs
Guardrail Support
#16 x 1pc
Guardrail Support
#14 x 1pc
#13 x 1pc
#15 x 4pcs
Ladder Rung
Ladder Rail ( Left )
Ladder Rail ( Right )
#7 x 1pc
Upper Back Side Rail
Upper End Guardrail
Upper End Guardrail
Lower End Guardrail
Lower End Guardrail

Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 4 of 10
#17 x 1Set
Full Slat Kit (13pcs)
Hardware List
#A x 16pcs
Bolt ɸ5/16" x 4"
#G x 11pcs
Screw ɸ1/4"x2"
#B x 16pcs
Barrel Nut ɸ5/16"
#C x 9pcs
Bolt ɸ1/4"x1-1/4"
#F x 7pcs
Bolt ɸ1/4"x1-5/8"
#D x 56pcs
Screw #4x30mm
#H x 6pcs
Screw Ø1/4"x3-1/8"
#J x 12pcs
Wood Dowel ɸ10x40mm
#E x 4pcs
Metal Dowel ɸ10x3-1/2"
#I x 1pc
Allen Wrench 4mm
Parts List
#18 x 1pc
Center Support Rail
#19 x 3pcs
Support Leg 300x30x30mm

Page 5 of 10
#A x 8pcs
#B x 8pcs
#B
#A
#I
#3
#4
#16
#6
#5
#10
#8
#12 #2
#7
#9
#12
#11
#1
#17
#14
#13
#15
#3
#4
#5
#6
#12
#18
#19
Exploded View
Insert barrel nuts (#B) to the side holes of the lower side rails (#5,6). Align lower side
rails (#5,6) to the holes of the lower end guardrails (#3,4), then secure by tightening
bolts (#A) onto barrel nuts (#B).

Page 6 of 10
#A x 8pcs
#B x 8pcs
#H x 6pcs
#J x 12pcs
#C x 9pcs
#F x 3pcs
#1
#2
#8
#7
#10
#9 #B
#12
#16
#12
#J
#H
#A
#I
#I
#12
#C
#I
#F
#I
#9
#7
#10
#8
1) Insert dowels (#J) to guardrails
(#9,10), then insert barrel nuts (#B) to
upper side rails (#7,8).
2) Align guardrails (#9,10) and upper
side rails (#7,8) to the upper end
guardrails (#1,2), then secure with
screws (#H) and bolts (#A).
Align guardrail supports (#12) to the guardrails,
then secure by using bolts (#C).
Align guardrail support (#16)
to the guardrails, then
secure by using bolts (#F).

Page 7 of 10
#E x 4pcs
#E #E
#E
#I
#G
#G
#G x 8pcs
#14
#13
#15
#I
#2
#4
#3
#1
Insert metal dowels (#E) to top holes of the lower
guardrails (#3,4), then carefully place upper bunk bed on
top of lower bunk bed.
Align ladder rungs (#15) to the ladder rails
(#13,14), then secure by using screws (#G).

#18
#I
#G
#G x 3pcs
Page 8 of 10
#F x 4pcs #F
#I
#F
#I
#19
#14
#13
#5
#8
Align ladder to the bunk bed, then secure by
using bolts (#F).
Align support legs (#19) to center support rail (#18), then secure by using
screws (#G). Adjust levelers of the support legs (#19) according to ground
level.

#D x 56pcs
#D
#D
ASSEMBLY IS COMPLETED
#17
#11
#5
#6
#7
#8
Page 9 of 10
Align slats (#11,17) to the bunk bed, then
secure by using screws (#D).

Page 10 of 10