Furniture of America CM-DK6162 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Rev:18-07-11
For more information contact our team: [email protected]
CM-DK6162

Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

#I x 1pc
Glue
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 8
Parts List
#1 x 1pc
Cabinet body
#2 x 4pcs
#3 x 2pcs
Bottom plate
#4 x 4pcs
Riser
#5 x 1pc
Backplane
#6 x 1pc
panel
#7 x 2pcs
#8 x 1pc
#9 x 2pcs
Drawer Top
In the mirror
side mirror
#10 x 2pcs
Mirror connecting rod
Leg
Hardware List
#A x 5pcs
Bolt Ø1/4" x 2"
#B x 5pcs
Barrel Nut Ø1/4"
#C x 8pcs
Bolt Ø1/4"x1-3/8"
#E x 8pcs
Flat Washer Ø5/16"
#F x 1pc
Allen Key 4mm
#D x 8pcs
Lock Washer Ø1/4"
Connect Iron
#G x 2pcs
#H x 4pcs
Wood Screw 3x1/2"

#I
Page 4 of 8
#1
#2
#1
#2
#1
#3
#3
#4
#4
#3
#I x 1pc
Attach legs (#2) to the bottom holes of the cabinet body (#1).
Align and attach the risers (#4) to the holes of the bottom plate (#3).
Pour glue (#I) into the hold (#3)
before installing the wood dowel

#I
#6
Page 5 of 8
#3
#4
#A x 2pcs
#B x 2pcs
#5
#6
#A x 3pcs
#B x 3pcs
#I x 1pc
#F
#A
#B
#1
#A
#B
#F
Insert barrel nuts (#B) to the holes of the bottom plate (#3). Make sure the barrel nut (#B) holes are facing
the same direction as the hole on the back side of bottom plate (#3). Align backplane (#5) to the holes of
the bottom plate (#3), then secure by attaching bolts (#A) to barrel nuts (#B).
Align the panel (#6) to the holes and wood dowels of
the rest of the cabinet. Insert barrel nuts (#B) to the
holes of the backplane (#5) and make sure the barrel
nut hole is facing upwards. Secure by attaching bolts
(#A) to the barrel nuts (#B).
Use a dab of glue (#I) onto the dowel hole of panel (#6)
before installing the wood dowel.

Page 6 of 8
#5
#6
#C x 4pcs
#D x 4pcs
#E x 4pcs
#C x 4pcs
#D x 4pcs
#E x 4pcs
#E #C
#D
#F
#E #C
#D
#F
#10
#10
#G x2pcs
#Hx 4pcs
#G#H
Prepare 4 bolts assembly by inserting lock washer (#D), then flat washer (#E)
onto bolts (#C). Align mirror connecting rods (#10) to the holes located in the
back side of the cabinet body (#1). Secure with bolts (#C).
Prepare 4 bolts assembly by inserting lock washer (#D), then flat washer (#E) onto bolts (#C).
Align mirror (#8) to the holes of the mirror connecting rod (#10), then secure with bolts (#C).
Align iron plate (#G) to the back of the desk.
Secure with screws (#H).

Slide the side mirrors (#9) down to the metal pole of the middle mirror (#8).
Unscrew the knob, then reattach the knob to the outside of the drawer.

Prepare 8 bolts assembly by inserting lock washer (#B), then flat washer (#C) onto bolts (#A).
Align legs (#2) to the holes of the cushion (#1), then secure with bolts (#A).