Furniture of America CM3558T User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-31
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3558T
2 PERSONS RECOMMENDED

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Table Top
#2 x 1 pc
Leaf
#3 x 2 pcs
Leg
#A x 16 pcs
Bolt 5/16”x1-3/4”
#B x 16 pcs
Flat Washer
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 16 pcs
Lock Washer
MD
#D x 1 pc
Allen Wrench
#4 x 1 pc
Rail
Page 3 of 5
#E x 4 pcs
Wood Dowel
#5 x 2 pcs
Leg Brace
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product
and to avoid any potential injury and/or damage.

I. Insert a wood dowel (#E) into
the leg (#3). Align the leg brace
(#5) with the wood dowel (#E)
and the pre-drilled hole of the
leg (#3).
II. Prepare a bolt assembly by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assembly through
the hole of the leg brace (#5)
and secure that bolt using the
Allen wrench (#D) to lock it in
with the leg (#3).
IV. Repeat the above process to
assemble the other leg brace
(#5) onto the other leg (#3).
I. Insert one wood dowel (#E) into
each of the leg brace (#5). Align
the rail (#4) with the wood dowels
(#E) and the pre-drilled holes on
the legs (#3).
II. Prepare 6 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
III. Insert 4 bolt assemblies through
the holes on the ends of the rail
(#4) and secure those bolts using
the Allen wrench (#D) to lock them
in with the legs (#3).
IV. Insert 2 bolt assemblies through
the hole of the leg brace (#5) and
secure those bolts using the Allen
wrench (#D) to lock them in with
the rail (#4).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 4 of 5
#A x 1 pc x 2
#B x 1 pc x 2
#C x 1 pc x 2
#E x 1 pc x 2
X 2
#A x 6 pcs
#B x 6 pcs
#C x 6 pcs
#E x 2 pcs
#3
#3
#5
#5

Page 5 of 5
ASSEMBLY IS COMPLETED
Carefully turn the completed table upright. Make sure the table is
rested on a flat surface and it does not feel loose or wobbly. If it
does, double check that the bolts are secured and properly tighten.
I. Carefully place the table top (#1)
facing down on a protected
surface.
II. Align the legs with the pre-drilled
holes on the bottom of the table
top (#1).
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer
(#C) onto the bolt (#A) and then
the flat washer (#B) onto the
SAME bolt (#A), in that order.
IV. Insert the bolt assemblies
through the pre-drilled holes of
the legs (#3) and secure those
bolts using the Allen wrench (#D)
to lock them in with the table top
(#1).
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. To extend the table, slide outward
on both ends of the two-piece table
top until there is sufficient opening
for the table leaf (#2).
II. Carefully place the table leaf (#2)
onto the open space of the table
top (#1).
III. Slide inward on both ends of the
two-piece table top until they are
touching and sitting flush with the
table leaf (#2).
Adjust the leveler according to the ground
level. To lower or to raise the leg, you need
to turn the leveler clockwise or
counterclockwise, respectively.